Can you erase a fault code on a Mercedes Benz?

Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships.

What are the fault codes for Mercedes airbags?

Call us at 888-779-9029 M-F 9-5 EST Review the table below for information on Mercedes airbag fault codes: The cause is the cable routing under the passenger seat. The wire was dressed from the factory such that the cabling to the connector was under tension.

What are all the codes on a Mercedes Benz?

Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.

What does the Mercedes Fault code p0801 mean?

Mercedes Fault Code Fault Code Meaning; P0801: Reverse Inhibit Control Circuit Malfunction: P0803: 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction: P0804: 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction: P0805: Clutch Position Sensor Circuit Malfunction: P0806: Clutch Position Sensor Circuit Range/Performance: P0807

How many control units does a Mercedes Benz have?

There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners.

What’s the fault code for a 2001 Mercedes Benz?

Click to expand… For the ML class it does not apply to the 2001 models. Also the fault code in the bulletin is for DTC B9103 and DTC B9123. No others would be covered by the DTB. Post # 34 in this thread lists the DTB the parts, and all affected models.

What is fault code b1859 on Mercedes Benz?

There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.

Where are the transmission codes stored in a Mercedes?

Specific codes related to the transmission are stored in the TCU (Transmission Control Unit) and come generic codes such as P0705 are stored in ECU (Engine Control Unit). You don’t need to pay anyone to read the codes; you can retrieve them yourself in a couple of minutes with the right OBD II scanner.

Is there an OBD-2 scanner for Mercedes Benz?

You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners. Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2.

How to check Mercedes Benz air conditioner trouble codes?

Push the left “AUTO” button to scroll forward and right auto button to scroll back. Depress right AUTO switch repeatedly. Note trouble codes Purchase a larger refill can of 134a with a gauge on it so you can read the low side pressure – helps as a guide to filling the system to the correct level.

What causes a Mercedes Benz to not start?

In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems

What is the SBC error code on a Mercedes?

This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F. After so many operation cycles the SBC looses efficiency or can completely fail while driving. So that you don’t get a failure while driving they want you to replace the SBC Hydraulic Unit before it fails catastrophically.

What is the SBC brake defective stop code?

SBC Brake Failure Error CODE C249F Fault – MB Medic Brake defective Stop Vehicle! SBC Brake Failure Error CODE C249F Fault If you have a Mercedes Benz with Sensotronic Brakes also known as brake by wire you may have been greeted with the “Brakes Defective Stop Vehicle” error message in your instrument cluster.

What are the common problems with Mercedes diesels?

Here are some common problems that affect many Mercedes-Benz diesel models including E350, ML350, GL350, R350, Sprinter, R320 CDI and BlueTec models. Common problems Diesel Particulate Filter. As Mercedes DPF traps and holds soot, with time it reaches a point when it needs to be ‘emptied out’. This is done by regeneration.

How do I reset the Check Engine light on my Mercedes?

The first way to reset a check engine light on your Mercedes-Benz is with a scanner. If you have one, simply plug it in, read the related codes, and press “clear” or “reset.” So long as the code issue has been resolved, it should go off.

What is the diagnostic code for Mercedes Benz?

HFM-SFI Hot-Film Engine Management Sequential Multiport Fuel Injection/ignition LH-SFI LH Sequential Multiport Fuel Injection System Engines 104, 119 Engine 120 Right Bank ME-SFI Motor Electronics with Sequential Multiport Fuel Injection/ignition System Engine 119 Engine 120, Right Bank

How long does it take to read a Mercedes code?

Depress Start button for at least two seconds but no more than four seconds, read codes. Read codes until first code displayed appears again. Codes will appear in ascending order.

How do you get serial code for Mercedes Benz?

Call back your dealer and give them the serial code. The code you get from using the serial number should definitively work. If you can’t reach a dealer you can try sending Mercedes-Benz cusomer service an email using this contact form. Make sure to provide your name, contact info, and VIN number of your car.

Do you need a radio code for a Mercedes Benz?

If you had a dead battery or replaced the battery, you may need to enter the code in your radio. Follow these steps if you need the Radio Code for your Mercedes-Benz. First take a look at your owners manual booklet. The code may be written down on a small business card size letter.

What are the diagnostic codes for Mercedes Benz?

Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent

What does Mercedes Fault code p0400 mean?

P0400 Mercedes Fault Codes Meaning Mercedes Fault Code Fault Code Meaning P0466 Purge Flow Sensor Circuit Range/Performa P0467 Purge Flow Sensor Circuit Low Input P0468 Purge Flow Sensor Circuit High Input P0469 Purge Flow Sensor Circuit Intermittent

What do you need to know about Mercedes Benz air suspension?

“AIRMATIC VISIT WORKSHOP!” message on the instrument cluster. This is typically an electrical fault. You will need an OBD II scanner such as Star Diagnostic or iCarsoft MB II to read the fault codes. Once you scan the car you may get fault codes.

Are there replacement parts for Mercedes Benz W220?

Suncore Industries carries a full line of new and remanufactured replacement parts for the W220. Complete conversion kits are also available for those that no longer want air suspension and prefer standard struts & coil spring suspension.

What do you need to know about Mercedes Airmatic suspension?

It also can carry pneumatic test if you need to test the airmatic systems including air compressor or the pressure release valve. These test can be performed on most Mercedes-Benz equipped with airmatic suspension such as: There are six areas which can cause the air suspension to stop working properly.

How to troubleshoot Mercedes Airmatic suspension using icarsoft MB II?

The iCarsoft MB II can read the fault codes and erase it but can not perform any further airmatic tests or troubleshooting. In this tutorial, we use Autel MaxiDAS DS708. It can read and clear codes for all systems on Mercedes-Benz cars.

What does the fault code on a Mercedes mean?

Mercedes Fault Code: P261F71 1 Check Engine Light 2 Little to no acceleration 3 Coolant leak 4 Brake Pedal Pressure 5 Engine overheating More

What are the options on a Mercedes-Benz W211?

When performing repairs on your W211 it is important to be able to identify standard items and optional features. Mercedes-Benz W211 models were option heavy due to being a higher-level model. In this tech article I will do my best to list each available item by model year breaks.

What causes a Mercedes-Benz transmission to fail?

We see these transmission fail in rare cases when water enters the transmission via the oil cooling lines or the radiator on cars equipped with Valeo radiators. The top part of the radiator on your Mercedes-Benz contains the chamber for the engine coolant/antifreeze while the bottom part contains the chamber for the transmission oil cooling.

What happens when a Mercedes Benz goes into limp mode?

When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level. The transmission has a dipstick tube but with no dipstick in it.

Can you read the fault code on a Mercedes Benz?

Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS

Is the Mercedes a class A190 a good car?

Our database has the answer No car is perfect, but we’ve gathered everything relating to the Mercedes-Benz A190 reliability here to help you decide if it’s a smart buy. Ewan Kennedy road tests and reviews the used 1997 – 2013 Mercedes A-Class.

When did the Mercedes a class come out?

Ewan Kennedy road tests and reviews the used 1997 – 2013 Mercedes A-Class. At the beginning of the 1990s whenever conversations turned to cars the issue of their styling always seemed to come to the surface.

What is the problem code for the O2 sensor?

P0133 – O2 Sensor Circuit Slow Response (Bank 1 Sensor 1) P0156 – O2 Sensor Circuit Slow Response (Bank 2 Sensor 2) P0411 – Secondary Air Injection System Incorrect Flow Detected Thanks for …

What does trouble code p0133 on OBD-2 mean?

What does that mean? This is considered a generic powertrain DTC (code). That means it’s definition is the same for all makes and models of OBD-II vehicles, however specific repair steps may vary depending on the vehicle. This trouble code involves the front oxygen sensor on Bank 1.

What to do if your Mercedes SL Class R129 is not charging?

An alternator that is not charging will eventually leave you stuck with a dead battery. Check your charging system. If your engine is running rough and misfiring you may need to change your cap, rotors and wires. If your valve cover gaskets are leaking we will show you how to replace them. Engine running lean/rough. Maybe you have a vacuum leak.

How to fix a Mercedes Benz SL500 problem?

Click to expand… put a full charge on it yesterday. Car is running outside now for about 15 minutes, will go and try radio again. put a full charge on it yesterday. Car is running outside now for about 15 minutes, will go and try radio again. Click to expand… CalCiCi, solved my problem.

Are there any free PDFs for Mercedes Benz SL Class?

Mercedes-Benz SL-Class PDF Workshop and Repair manuals, Wiring Diagrams, Parts Catalogue, Fault codes free download! Mercedes-Benz SL – a series of light sports cars luxury-class German automotive brand Mercedes-Benz, produced since 1954.

Are there any problems with the Mercedes SL500?

Hey Guys, I have a 2000 sl500. Went out for a ride around on radio, but no sound. and could not put code in. Nothing will work, no CD, radio, tape, or phone.

What is the option code for Mercedes W123?

Some of the options became standard during the time a car series was built (e.g. code 422 Servolenkung SV/ power steering for W123 became standard since the beginning of modelyear 1983). Codes in the form of e.g. 42/2 power steering W114/115 denote the older code system.

What are the error codes for Crown forklifts?

CROWN Forklift Truck Error Codes DTC 1 (1) TurnOnMil 2 (2) DelayedEngine Shutdown 3 (3) CheckEngineLight More …

When do I need to use a decline code?

Decline codes are provided when a transaction cannot be completed, so it’s good to know the explanation for each of them. Let’s dive deeper into the most common declining codes merchants need to handle. Based on our internal analyses, one of the most common codes that merchants receive is code 05.

What kind of transmission does a Mercedes Benz W210 have?

The 722.6 transmission is now used in a number of Daimler-Chrysler (Now Daimler only.) vehicles. A five-speed manual is also available, although after the facelift in 1999, it was replaced by a six-speed manual.

When did the Mercedes Benz W211 come out?

E-Class is another Mercedes-Benz model that doesn’t mind the high mileage. The W211 model was a complete redesign from the previous generation E-Class. If you ask around some will say to avoid the early W211 model years such as: 2003, 2004 and 2005.

What is the fault code for Mercedes Bank 2 sensor?

P0153 O2 Sensor Circuit Slow Response (Bank 2 Sensor 1) P0154 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1) P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1) P0156 O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)

Which is the best OBD code reader for Mercedes Benz?

Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2. BlueDriver Scan Tool for iPhone and Android

How to correct trouble code p2138 Mercedes-Benz C class?

Wait a minimum of two minutes for the ECU to reset itself. During this time, the calibration mechanism of the TPS should reset, and send the correct throttle plate as well as pedal positions to the ECU. Test drive the car to make sure the issue has been resolved. If it has not, the TPS will most likely need to be replaced.

What are the model codes for Mercedes Benz?

Pages in category “Mercedes-Benz model codes” 1 Mercedes-Benz R107 and C107 2 Mercedes-Benz SL-Class (R129) 3 Mercedes-Benz SLK-Class (R170) 4 Mercedes-Benz SLK-Class (R171) 5 Mercedes-Benz SLK-Class (R172) 6 Mercedes-Benz SL-Class (R230) 7 Mercedes-Benz SL-Class (R231)

What is the fault code for a Mercedes heater?

P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1) P0136 O2 Sensor Circuit Malfunction (Bank 1 Sensor 2) P0137 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2)

What causes a Mercedes Benz steering angle sensor to lose memory?

B1628 Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. Body C1140 BAS light, play in steering column causes steering angle sensor to lose memory (?) Chassis C1504 BAS light, play in steering column causes steering angle sensor to lose memory (?) Chassis P0818 Driveline Disconn. Switch Input Circuit Malfunction

Where are misfire codes stored in a Mercedes?

Luckily for you, the misfire codes are stored in the ECU and are very easy (and inexpensive) to retrieve. To diagnose an engine misfire on a Mercedes all you need is a generic OBD II code reader that can be bought in some cases for under 20 at your local auto parts store or on Amazon’s Best Selling OBD II scanners list.

How to replace a camshaft on a 07 E350?

Lol………Thanks for your help………Also its a 07 E350 NON 4-matic. The one you need to replace is labeled as #2 in the picture. The camshaft solenoid/magnet is around $25 from the dealership. Just crack loose the bolts with that wrench and then loosen the all the bolts by hand.

What do I need to troubleshoot my Mercedes Benz?

Troubleshooting fuel related problems is not very difficult and you can check the fuel pressure yourself. Checking the fuel pressure is very simple. For this test, you will need a fuel pressure gauge. What you need is a fuel pressure gauge with Schrader valve adapter.

How do I Turn Off the ESP light on my Mercedes?

ESP light stay on constantly if the “ESP Off” button was pressed. To turn it off: Press the ESP button on the dash of your Mercedes-Benz and hold it for 5 seconds. This will reset the light.

What is the ESP warning light on a Mercedes E350?

2008 E350….Esp warning light came on stating inoperative… 2007 mercedes dash board indicates that: ESP inoperative- see user manual- with triangle indication on. Last week I went for services they said … read more Master Automotive Technic… MB E350 4 matic 2010. Lots of rain in Houston. Pre safe now MB E350 4 matic 2010.

When did I buy a 2007 Mercedes E350?

Well, we bought the extended warranty (36 months / 100,000 miles) on our CPO 2007 E350 in February 2011 when we purchased the car. We were coming home from work in January 2014 when our transmission locked in 1st gear and could not be shifted manually or automatically.

Are there any problems with the Mercedes E class?

The only problem has been with the transmission which was fixed under warranty by a dealer in Hyannis MA. It required an overnight at the dealer while the part was shipped in. Since then I have driven the car cross country to Arizona and had no problems. The sound system and my Sirius radio are wonderful. I also got over 31 MPG on the trip.

What kind of compressor does a 2002 Mercedes E320 have?

2002 Mercedes E320 compressor had 12 volts but won’t engage . read more Lou Palomino associates in automotive technology 11,061 satisfied customers EC light will not turn off not getting air conditioning

Who is the Mercedes mechanic for the E320?

Answered in 1 minute by: 3/29/2012 Mercedes Mechanic: Marty, Mercedes Technician replied 9 years ago Marty, Mercedes Technician Category: Mercedes Satisfied Customers:57,141 Experience: Bosch Certified Master Tech. Over 35 years experience. Verified eurotec :

How to clear air con codes on A203?

My car is the w210 chasis so not sure if it will work on a203.Read the first post and pull faults codes on the AC module (where you control your temp in the car) and then clear the faults – this will enable your AC – otherwise you need to plug in and have das/star clear codes for $$$$. Air con recharge but EC still on. codes access?

Where can I find the Mercedes Fault code?

Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes. The codes above are retrieved by plugging a diagnostic scanner into the OBD-II port located under the dash, and scanning for fault codes. Location of OBD II port used to retrieve Mercedes-Benz fault codes.

Where can I find Mercedes E220 W210 diagnostic code?

Mercedes e220 w210 There is an app called DTC Search . You can select model of car then enter the code and it gives a detailed description for the code and possible reasons etc . Found it really helpful and easy to use. Aug 18, 2013 1,934 East Riding/Germany/Denmark CL 63 Biturbo 2014 – S63L 2010 – CLS Weistec MSL Monster (RIP)

Is there a diagnostic scanner for Mercedes Benz?

Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships. Yes, it can do anything including programming of sensors and features. Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes.

Why is my Mercedes Benz W210 not working?

Old, worn out oxygen sensors can cause poor mileage, low power and a variety of fuel injection problems. Learn to replace them today with our article. The mass air flow sensor on the W210 is notorious for failing. Replacement is just a 15 minute job with this handy technical article. Over time, fuel injectors can get clogged and stop working.

Is there a service bulletin for a Mercedes Benz?

We located a Mercedes Benz Service Bulletin (S-B-14.00/17) that may be helpful. Also, one customer with a 2002 Mercedes was unable to complete the secondary air injection monitor until one evening he allowed his vehicle to idle for 5-20 minutes in his driveway.

When did the Mercedes Benz W123 come out?

W123 is the internal chassis-designation Mercedes-Benz used for their executive line of cars, manufactured between 1976 and 1985. Within the W123 chassis, as it typical for Mercedes of the era, cars were named after their engine size, fuel type, and chassis sub-type.

Where are the fuses on a Mercedes Benz E class?

Cigar lighter (power outlet) fuses in the Mercedes-Benz E-Class are the fuses #54a, 54b (cigar lighters) in the Engine Compartment Fuse Box, and fuse #13 (Interior socket) in the Luggage Compartment Fuse Box. The fuse box is located on the driver’s side of the instrument panel, behind the cover.

What are the warning lights on a Mercedes Benz?

The following are warning lights and indicators found in vehicles built by Mercedes Benz. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 40 of them so be patient!

What are the K lines on a Mercedes?

6 K-line diagnostics passive safety systems – airbags, belt pretensioners (SRS, AB). Output for resetting the service interval (?) 7 K-line diagnostics of the control system of the air conditioner and heater (Tempmatic, Automatic), control systems of safety arcs (RB – to R129)

How to reset wrench on 1998 Mercedes ML320?

Video Reset Wrench Service Due Message on 1998-2005 Mercedes ML320: Close all doors, hood, and trunk lid and turn the ignition to position II (ON) Within 4 seconds of turning key on, press the “0” button (located on instrument cluster) twice quickly Within 10 seconds, turn the key to position 0 (OFF)

How to reset the computer code on a Mercedes C class?

Turn the ignition switch to “ON.” Press the power button on the scan tool, if it does not come on automatically. Wait for the tool to complete the scanning process. Press the “Reset” or “Erase” button on the scan tool to reset the computer codes. “Mercedes-Benz C-Class Operator’s Manual”; Mercedes-Benz USA, LLC; 2010

What is the repair manual for a Mercedes Benz?

Mercedes-Benz Series 107, 123, 124, 126, 129, 140, 201 CAR SERVICE & REPAIR MANUAL (1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993) – DOWNLOAD! Download Now

How to reset service wrench on Mercedes ML?

Press and hold the “0” button and turn the ignition back to position II (ON) Continue to hold the button for 10 seconds or when you hear a signal sound and see the new service interval Release the button and switch the ignition to position 0 (OFF) We hope you find these reset procedures helpful.

When is the p0410 Mercedes-Benz code detected?

Most auto repairs shops charge between $75 and $150 per hour. When is the P0410 MERCEDES-BENZ code detected? The secondary air injection system does not detect the presence of air in the exhaust when introduced by the secondary air injection system. An air pump is used on the vehicle to lower tail pipe emissions on start-up.

Are there any misfires on my 2001 e320?

My 2001 E320 had misfires on cylinder 4 and occaisionaly a rough idel. I left the coils and swapped the wires with cylinder 1 and the problem moved. replaced the wires and runs prefectly now. After moving the coil pack for cylinder 1 & 6 the problem moved.

What’s the fault code for an e320 wagon?

1994 E320 Wagon,1999 E320 Wagon,2000 E 320 Wagon, MGB Track/Rally, ,1988 300E ,more…. are 2 years past due to be changed.Start the attack there and then proceed. Bad gas is the thing of the past, at least in CA where for several years all stations have double wall tanks.

What’s the name of the Mercedes Benz parking light?

Parking light. P21/5W. Front turn signal. P21/5W. Rear turn signal. P21W. Tail light. 5007 or 12821 or R5W. Tail light.

Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2. BlueDriver Scan Tool for iPhone and Android

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More

What’s the fault code on a Mercedes 190E?

It’s W201 190E, with M111 engine (2.2Lt.) from E220, W124. There is no major symptom, just very little rough idle. I made the DIY code reader and check it, then found those codes. What I confused is…which “set”of codes I should refer to…

What’s the fault code for a Mercedes 300?

# Flashes PROBABLE CAUSE for Mercedes vehicles 300 series (2.8L and 3.2L) 1991 and later. Going by his listing you may have been looking at the 3.2 litre fault codes ? I haven’t had time to check, but how does the info compare to this source? I haven’t had time to check, but how does the info compare to this source? Click to expand…

What do the codes mean on a Mercedes?

P – is for powertrain codes – the code is related to the operation of the engine and / or automatic transmission B – is for body codes – the code is associated with the work of “body systems” (airbags, central locking, power windows) C – is for chassis codes – the code refers to the chassis system (chassis)

Navigation