How much does it cost to replace ignition coil on Saturn Ion?

The ignition module or an ignition coil may fail causing an engine misfire, the Check Engine Light may or may not illuminate. Diagnoses will be required to determine the cause and needed repair. The average cost for a Saturn Ion Ignition Coil Replacement is between $312 -$326.

What’s the problem with my 2004 Saturn Ion?

I’m frustrated say the least with my 2004 Saturn ion. I recently had both recalls taken care of and changed the oil, fixed brakes and EVERYTHING and now my car is driving horribly. It shutters everytime i drive it and when i come to a complete stop or put the car in reverse the engine shuts off which is very dangerous.

Why does my car’s ignition coil keep failing?

Ignition coils tend to fail because of bad spark plugs or plug wires. If your vehicle’s fuel-to-oxygen mixture is either rich or lean, therefore, your ignition coils may fail prematurely. Additionally, engine heat and vibrations can cause damage to ignition coils.

Where was coil on plug ignition presented at?

Presented at 2011 Fall ICAIA conference, Ranken Technical College, St. Louis This Article is brought to you for free and open access by the Department of Automotive Technology at OpenSIUC. It has been accepted for inclusion

What should I put in my Saturn Ion 2?

Put in injector cleaner, chaned boots, plugs, and coil. Also chaned out fuel filter. Next step is ignition coil. Only code coming up is a random misfire code. Still in the process of repairs. I have a 2006 Saturn ion 2 with 71350 miles.

What causes a misfire in a Toyota Prius?

Started by stalling and idling. Got coil pack and spark plugs changed. Ran great for a couple miles then engine light started blinking and the exhaust sounded loud while accelerating. Misfire in cylinder 4. Brought back and said it needed a new coil pack which I just did. Ran great for a couple miles and misfires again.

What’s the engine code on a 2004 Saturn Ion?

2004 Saturn ION with Ecotec 2.2: Engine misfire with code P0300, ICM problem? Car came in with a misfire complaint and check engine light on with code p0300. Looking at misfire history confirms high misfire counts on cylinders 1 and 4 along with lower counts on cylinders 2 & 3. Fuel trims OK LTFT < 10. Plugs are fouled.

What’s the misfire count on a Toyota Prius?

Car came in with a misfire complaint and check engine light on with code p0300. Looking at misfire history confirms high misfire counts on cylinders 1 and 4 along with lower counts on cylinders 2 & 3. Fuel trims OK LTFT < 10. Plugs are fouled. Compression tests ~200psi on each cylinder.

What can cause an ignition system to misfire?

A typical modern ignition system contains a variety of components, including the control module, crankshaft position sensor, coil packs, wiring and, of course, the spark plugs. Issues with any of these parts can result in an engine misfire. 2. Air and fuel delivery problems

How to test cylinder misfires and ignition coils?

Please try again later. MotorWeek’s Pat Goss (RockAuto.com is a MotorWeek Sponsor) shows what to check first when a cylinder misfire code shows up on an OBD scan tool. This includes how to test modern coil on plug ignition coils with a spark tester (available under “Extras” at RockAuto.com). Loading…

What is the diagnostic code for an engine misfire?

When the check engine light illuminates, your car’s primary computer, which is often referred to as the powertrain control module (PCM), will store a diagnostic trouble code (DTC) in its memory. Codes P0300 to P0312 are the primary DTCs associated with an engine misfire.

Why does my No.3 Cy misfire smell of gas?

No.3 Cy misfire, and the engine light is on, i’ve changed the filter and cleaned the oil pipe, but it doesn’t work. Sometimes, when the engine light is on, there is a light smell of gas. Same problem, many trips to dealer and unsuccessful repair.

How to troubleshoot the ignition system in a Saturn Ion?

It primarily involves checking for sparks on the spark plugs and ignition coils. Remove a park plug wire from the plug and connect it to a spark tester. Ground the tester to the engine, crank the engine and look for a strong spark. Repeat for all the Ion’s wires.

What is the Check Engine Light code for Saturn?

P1272Accelerator Pedal Position Sensor 2 P1273Accelerator Pedal Position Sensor 1 P1274Injectors Wired Incorrectly P1275Accelerator Pedal Position (APP) Sensor 1 Circuit – Read Our Article on Automotive Circuit TestingFor Help With This Saturn Check Engine Light Code P1276Accelerator Pedal Position (APP) Sensor 1 Performance

What should crankshaft resistance be on Saturn Ion?

Measure the resistance between the crankshaft position sensor’s terminals A and B. (Disengage the DIS module’s five-pin connector first). The resistance should be 700 to 900 ohms. Remove the crankshaft sensor from the engine if the resistance was off.

Navigation