Where are the belt lights on a prairie 360?
These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them.
Where are the plugs on a Kawasaki Prairie 360?
Then, find the black and grey plugs up under the gas tank cover. These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were.
What to do if prairie 360 4wheel drive goes into error?
If the belt is good you just need to adjust it if needed and reset the belt switch. The 2×4 4×4 goes into error and flashes if you turn on the ign switch with the connections on the actuators unplugged. So when you correct the belt prob you should be ready to ride.
What’s the speed of a Kawasaki Prairie 360?
Starts just fine and idles fine. Just no speed does about 15-20 mph. I am assuming due to belt and being in limp mode. Also noticed it takes a second or two to get going once i place i gear. Would like to get it running right and start using it more.
What causes a Kawasaki Prairie 360 to stall?
Would that be the cause of the engine stalling when i put it in gear i put it in 4×4 on jack stands and its engaging. So four wheel drive is working. My cell is XXXXXXXXXX if thats quicker to contact me. did you measure the resistance between the red to black, yellow to blue and orange to blue on the engine braking controller?
Why do my 4×4 lights keep flashing?
I have an 2006 Kawasaki Prarie 360 and the 4×4 lights keep..atv..bike… their is a failure in the actuator controller system and that is why the 4X4 light is flashing. how many seconds apart are the flashes? I looked it up in the manual and it seems like its only the engine brake. Its like one long second or two seconds.
Then, find the black and grey plugs up under the gas tank cover. These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were.
These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them.
Why is the belt light flashing on my KVF 360?
The 4×4 and the Belt light are flashing. The Belt is brandnew and was changed from a Kawasaki dealer. Another problem is, that the KVF is driving normal and maybe a 10 minutes later the ATV has no power and makes misfire. After i turn the ignition off and wait a few minutes everything is normal for another 10-30 minutes.
Would that be the cause of the engine stalling when i put it in gear i put it in 4×4 on jack stands and its engaging. So four wheel drive is working. My cell is XXXXXXXXXX if thats quicker to contact me. did you measure the resistance between the red to black, yellow to blue and orange to blue on the engine braking controller?
What kind of CARB dip do you use on a Kawasaki Prairie 360?
I recommend the Yamaha carb dip because it works and it will not affect rubber part like most carb cleaners will. Yamaha’s Carb Dip needs to be mix 50/50 with warm water. After you dip the carb it will need the all jets and passages verified with spray carb cleaner to make sure the fluid will make it through the intended passage.
Is there a belt Trip Switch on a Kawasaki 360?
This has been the case with many 360 owners, they found them after looking further. There is a procedure in the Vforce folder for the Vforce to reset the light. The Vforce does not have a belt trip switch. Note: Disconnecting the battery does not reset the light.
When to reset belt light on Kawasaki ATV?
However, the belt light may stay on after flipping the switch back to “ON”, or it may have come on automatically at 100 hours to get you to return the machine to the dealer for inspection even though the belt switch is not tripped. The following procedures will reset the light if the belt switch is not tripped.
Where is the belt light reset button on a Kawasaki P650?
Belt light reset procedure for late 2003 and later P650, P360, and BF650SRA. 1. Turn the ignition switch OFF. 2. Disconnect both sets of 5 pin connectors located above the CVT cover. Note: These connectors are located just beneath the shift handle on the right side of the 650; one is black and one is grey.