Is there an injector pulse on my car?
SOLVED: I have no injector pulse. I have plenty of fuel – Fixya I have no injector pulse. I have plenty of fuel pressure and both crank sensors and the cam sensor are good. If I spray carb spray through a vacuum hose, it runs fine, but I’m getting nothing through the injectors.
Why does my carb spray have no injector pulse?
I have no injector pulse. I have plenty of fuel pressure and both crank sensors and the cam sensor are good. If I spray carb spray through a vacuum hose, it runs fine, but I’m getting nothing through the injectors. What else besides the PCM would control the injectors other than the cam and crank sensors?
Can a PCM loose all 6 injectors at once?
The PCM is set up so that it has individual injector drivers, Meaning that you could loose 1 or 2, but loosing all 6 at one time is very unlikely. Injectors do run off both crank and cam sensors, but mostly off the cam. And when the cam sensor does fail, The PCM goes into default mode, using the last stored run.
Why does my 1998 S10 Blazer not run?
My buddies 1998 S10 Blazer will not run. When you hit the key the engine turns over and starts normal but dies right away. It gets gas from the initial priming but that’s it. It will do this all day long. The fuel pump was replaced 3 months ago, you can hear it running as soon as you turn the key on.
Why is my injector pulse not working on my car?
Ans: Having a stuck or clogged injector is a very wide known problem that happens because of the accumulation of carbon build-ups that coming out from using a low-grade fuel, so regularly using a fuel system cleaner can help you in this mission.
What happens when a fuel injector is disabled?
When this occurs, the security indicator will flash. After three consecutive failed tries, the system will enter into a long tamper mode. In this mode, the fuel injectors will be disabled for approximately 10 minutes, and the security indicator will be flashing.
What causes no power to fuel injectors?
The most important signals that determine the accuracy of a signal coming out of ECU to injectors are crankshaft position sensor and camshaft position sensor, so to test a bad injector, you have to check the voltage on the injector when the ignition key is turned on: NO VOLTAGE? , so what causes no power to fuel injectors?
How does the engine control unit control the injector pulse?
Question: What controls the fuel injector pulse? Ans: The engine control unit is the electronic brain that used to control the fuel injector pulse by gathering data from various sensors along the fuel line
What does it mean when there is no injector pulse?
In case of that, there is no injector pulse or spark, this means that is your ECU has failed in operating in this case you have to get your ECU changed or visit an expert. You May Like: Low Fuel Light Comes on When Tank Is Full Causes and How to solve it Question: What controls the fuel injector pulse?
I have no injector pulse. I have plenty of fuel pressure and both crank sensors and the cam sensor are good. If I spray carb spray through a vacuum hose, it runs fine, but I’m getting nothing through the injectors. What else besides the PCM would control the injectors other than the cam and crank sensors?
The most important signals that determine the accuracy of a signal coming out of ECU to injectors are crankshaft position sensor and camshaft position sensor, so to test a bad injector, you have to check the voltage on the injector when the ignition key is turned on: NO VOLTAGE? , so what causes no power to fuel injectors?
Question: What controls the fuel injector pulse? Ans: The engine control unit is the electronic brain that used to control the fuel injector pulse by gathering data from various sensors along the fuel line
How do you test a fuel injector ( ANS )?
Ans: By using a simple diagnostic tool called NOID light, this tool detects a digital signal coming from the ECU and flashes an LED light, so if there is no LED flashing during cranking, this means that there are no pulses coming out of the ECU. Question: How do you test a fuel injector?
SOLVED: I have no injector pulse. I have plenty of fuel – Fixya I have no injector pulse. I have plenty of fuel pressure and both crank sensors and the cam sensor are good. If I spray carb spray through a vacuum hose, it runs fine, but I’m getting nothing through the injectors.
Ans: By using a simple diagnostic tool called NOID light, this tool detects a digital signal coming from the ECU and flashes an LED light, so if there is no LED flashing during cranking, this means that there are no pulses coming out of the ECU. Question: How do you test a fuel injector?
What causes the fuel pump to not start?
The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.
How is the speed of the injector controlled?
The injector in a basic picture is an electronically controlled valve that is supplied with pressurized fuel from the fuel pump at a certain pressure level injector can be electromagnetically opened and closed at very high speed—this speed controlled by the electronic control unit using.
The injector in a basic picture is an electronically controlled valve that is supplied with pressurized fuel from the fuel pump at a certain pressure level injector can be electromagnetically opened and closed at very high speed—this speed controlled by the electronic control unit using.
How can I test the resistance of my injector?
Another way to test the injector is to measure the resistance of every injector between the two terminals and compare it with the highest and lowest values stated in the injector datasheet; if the result outside the allowable boundaries, then change this injector.
What are the signals for the fuel injectors?
There are three signals which are necessary to operate the fuel injectors. These are the Ne, G, and IGf signals. Inside the ECU, the Ne Signal is used to produce an injection chive signal.
The PCM is set up so that it has individual injector drivers, Meaning that you could loose 1 or 2, but loosing all 6 at one time is very unlikely. Injectors do run off both crank and cam sensors, but mostly off the cam. And when the cam sensor does fail, The PCM goes into default mode, using the last stored run.
Where is the fuse for the fuel injector located?
Blown injector circuit fuse Bad fuel injector power relay A fault in the wiring harness to the injectors So, the injector fuse and relay are usually located; in the relay box or power distribution center in the engine compartment. Fuses are used to protect various electrical circuits, while supplying power to components.
What causes a no start no injector pulse?
The first time I ran into one of these, I mistakenly replaced the engine computer in an attempt to fix the no injector pulse condition. It is strange that one shorted fuel injector can cause all the other injectors to not fire, but this is exactly what can happen with a group fired system.
What causes no power to fuel injector pulse?
Ans: The engine control unit is the electronic brain that used to control the fuel injector pulse by gathering data from various sensors along the fuel line Question: What causes no power to fuel injectors?