How do you get the spare tire off a Jeep Liberty?
Fit the jack handle extension over the drive nut located in the rear cargo area inside the vehicle. Use the lug wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out from under the vehicle.
Where is the jack on a 07 Jeep Liberty?
The scissor-type jack and tire changing tools are located in the cargo compartment behind a trim cover on the left rear trim panel. The latch is located at the bottom of the trim cover.
Where is the floor jack on a Jeep Liberty?
4. Locate the jack as shown. For the front tires, place it (rearward) of the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed.
Where is the jack on a 2005 Jeep Liberty?
Online Viewer
- Jack Location.
- The scissor-type jack, and tire changing tools are stored.
- beneath the right rear seat.
- stowage position, turn the thumb screw counterclock-
- wise to loosen jack assembly and then remove it.
- Spare Tire Stowage.
- To remove the spare tire from the carrier, remove the tire.
What size tires does a 2012 Jeep Liberty have?
| 2012 Jeep Liberty | ||
|---|---|---|
| Rim Size | Tire Sizes | Jeep Liberty Options |
| 16-Inch | 225-75-16 235-70-16 | Sport |
| 17-Inch | 235-65-17 | Limited |
| 18-Inch | 235-60-18 | LimitedSport |
Where is the Jeep JK jack location?
The jack and lug wrench are located in the rear storage compartment.
How to mount a spare tire on a Jeep Liberty?
Position the spare wheel/tire on the vehicle and install lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. WARNING!
How do you change the tires on a car?
For the front tires, place it (rearward) of the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw to the right.
How do you jack up a Jeep Liberty?
1. Remove spare tire. 2. Remove jack and tools from mounting bracket. Assemble the tools by connecting the driver to the extension, and then to the lug wrench. 3. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground.
What should wheel nut tightness be on Jeep Liberty?
The correct wheel nut tightness is 95 ft lb (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10.
Position the spare wheel/tire on the vehicle and install lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. WARNING!
For the front tires, place it (rearward) of the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw to the right.
1. Remove spare tire. 2. Remove jack and tools from mounting bracket. Assemble the tools by connecting the driver to the extension, and then to the lug wrench. 3. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground.
The correct wheel nut tightness is 95 ft lb (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10.