Where is the Diagnostic Code on a Hyundai?

With ignition switch in the On position, ground the No. 10 terminal (L wire) of diagnostic connector for approximately 2.5 seconds. The diagnostic connector is located on the left hand kick panel. The first diagnostic trouble code or no fault detected will be indicated by the on-board diagnostic lamp.

What is the fault code for a Hyundai airbag?

Airbag Fault Code DTC B1101 Battery Voltage High B1102 Battery Voltage Low B1326 FIS Front Impact Sensor -Driver Short to Ground

What is the fault code for a Hyundai excavator?

Troubleshooting of Hyundai Excavator fault code DTC / error code Hyundai 9 series excavators error codes: 101 3 hydraulic oil temperature sensor circuit – Voltage above normal or shorted high voltage 4 hydraulic oil temperature sensor circuit – Voltage below normal or shorted to low voltage

What is the DTC code for a Hyundai?

In this article, you will find a complete list of Hyundai Trouble Codes. This list contains more than the Hyundai Check Engine Codes. Here you will find Hyundai ABS, Airbag, and Transmission DTC codes. P0244 Turbocharger/Supercharger Wastegate Sol.

Where do I find the fault code on my Hyundai?

Connect your OBD-II scanner into the OBD-2 port under the dashboard on the driver’s side. Note: Even a $20 generic OBD-2 scanner can retrieve check engine / ECU Hyundai fault codes. Those are P-codes in the Hyundai list below.

Airbag Fault Code DTC B1101 Battery Voltage High B1102 Battery Voltage Low B1326 FIS Front Impact Sensor -Driver Short to Ground

What to do if your Hyundai has code p0456?

If your gas cap was not loose and you do not see any indications of failure, try replacing the gas cap anyways and clearing the codes. Gas caps are relatively inexpensive and are often the fix for code Hyundai P0456. Inspect the fuel tank and charcoal canister for damage and leaks. Replace if necessary.

What are the computer codes for Hyundai Sonata?

COMPUTER CODES for Hyundai Vehicles. CODE Hyundai Sonata, Excel (90 on), Scoupe (9 1 Electronic Control Unit (ECU) (one long 2 ECU system normal 11 Oxygen sensor or circuit 12 Airflow sensor or circuit

What are the codes for the Hyundai Elantra?

If codes reappear, substitute a known good ECM, and recheck codes. Hyundai Stellar vehicles. Hyundai Sonata, Excel (90 on), Scoupe (91 & 92), Elantra. Hyundai Scoupe (93 through 95) and Accent vehicles.

Where is diagnostic connector on Hyundai multi use tester?

Connect harness connector of multi-use tester to diagnostic connector in fuse box, located on left kick panel. Connect power-source terminal of multi-use tester to cigarette lighter socket. Turn ignition switch On, then use multi-use tester to read self-diagnostic codes.

What is the fault code for the Hyundai Elantra?

Hyundai Sonata, Excel 90 on , Scoupe 91 & 92 , Elantra. Hyundai Scoupe 93 through 95 and Accent vehicles. 4155 ECM failure A/C relay, IAC, PC.” You will need a Hyundai multi-system OBD-2 scanner to read Hyundai specific fault codes.

What kind of engine codes does a Hyundai have?

This list contains more than the Hyundai Check Engine Codes. Here you will find Hyundai ABS, Airbag, and Transmission DTC codes. P0244 Turbocharger/Supercharger Wastegate Sol. ‘A’ Range/Performance P0245 Turbocharger/Supercharger Wastegate Sol. ‘A’ Low P0246 Turbocharger/Supercharger Wastegate Sol. ‘A’ High

What does a p2127 code on a car mean?

Although generic, the specific repair steps may vary depending on make/model. A P2127 code means that the the car’s computer has detected that the TPS (throttle position sensor) is reporting too low a voltage. On some vehicles that lower limit is 0.17 – 0.20 volts (V). The “E” refers to a particular circuit, sensor, or area of a particular circuit.

What does the p0320 Hyundai ignition failure sensor do?

P0320 Hyundai Description Ignition failure sensor is used to check whether the spark ignition is occurred correctly or not and also used to tachometer drive. The sensor monitors the voltage difference between a resistance which is on the battery circuit for ignition coil.

What was my experience with the Hyundai Accent misfires?

Hyundai is a crap company with crap service. They tell you the spark plugs are suppose to be gapped at .44 to make a buck off you, so when it misfires you can take it in for work, and they can charge u for all kinds of services you dont need! Plus charge you for labor too.

Why are my Hyundai Accent coils not working?

OEM equipment SHOULD be able to create a spark with this. that then leads me to believe that the OEM coils are rather weak and hyundai is really pushing it with that 0.044″ spec on the plugs. the coils simply do not push out enough voltage for the specified plug gap.

What is the failure code on a Hyundai?

As an example, one flash, followed by a 2 second pause, followed by two flashes and another 2 second pause, followed by two flashes and a 2 second pause, followed by three flashes and another 2 second pause, indicates a failure code 1223.

What does code 42 mean on a car?

CODE 42 – Electronic Spark Timing or Bypass Fault Trouble Code 42 indicates that there may be a malfunction in the Electronic Spark Timing (EST) system. During cranking, the timing is controlled by the ignition module while the ECM monitors the engine speed.

What are the conditions for setting code 42?

The conditions for setting code 42 are: System in BYPASS mode but the ignition module is still controlling timing – or – Engine speed > 600 RPM with no EST pulses (ECM controlled timing) going to the ignition module for 200 msec. Typical causes for this code 43 include: 1) BYPASS line is open or grounded 2) EST line is open or grounded

What are the causes of a GM code 42 spark fault?

1) BYPASS line is open or grounded 2) EST line is open or grounded 3) PROM or CALPACK not seated properly in the ECM 4) Poor connections between ignition module and ECM 5) Poor routing of EST harness and/or poor quality ignition wires (EMI induced electrical noise) 6) Faulty or incorrect ignition module 7) Faulty ECM Return to Chart

Navigation