What is the transmission code on a 2002 C240?

My C240 (US) went into limp mode, and initially stored code P0705. The check engine light would sometimes be on, sometimes off. Took it to a transmission specialist and he got the following codes: P2400 The right rear wheel rpm signal sent from the traction system via the CAN bus is implausible.

Can you read the fault code on a Mercedes Benz?

Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS

Is there a diagnostic scanner for Mercedes Benz?

Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships. Yes, it can do anything including programming of sensors and features. Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes.

Where are the transmission codes stored in a Mercedes?

Specific codes related to the transmission are stored in the TCU (Transmission Control Unit) and come generic codes such as P0705 are stored in ECU (Engine Control Unit). You don’t need to pay anyone to read the codes; you can retrieve them yourself in a couple of minutes with the right OBD II scanner.

How to check for a Mercedes Benz p0500 code?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P0500 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city.

What does a stored code p2500 on a PCM mean?

A stored code P2500 means that the powertrain control module (PCM) has detected a lower than expected voltage signal from the generator lamp control circuit. The L simply reiterates the lamp control circuit. The generator lamp is contained in the instrument panel.

How much does it cost to diagnose a Mercedes-Benz code?

The cost to diagnose the P0500 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?

Why does my Mercedes Benz engine not start?

However, when i turn the key all the way, the engine does not even try to crank. It almost feels as if only the starter is disconnected or something from the car entirely. (I know nothing about car engines)

When does vibration start in a Mercedes Benz?

Mercedes-Benz the engine mounts start to loose fluid around the 100k mile mark. Once a crack develops on the motor mount, they loose all the fluid over time and the vibrations get worse. Mercedes cars have three mounts.

When did Mercedes Benz start using 5 speed transmission?

The 5-speed transmission that was used between 1995 up to 2008 is one of the best transmission ever built. Now let’s see if we can help you troubleshoot your transmission. By continuing to read this article you agree to use this information at your own risk. Top 5 Mercedes-Benz Transmission Problems.

What happens if the crank on a Mercedes Benz goes bad?

Symptoms of a defective crankshaft position sensor on a Mercedes-Benz. Failed crankshaft position sensor can also impact the idling, the acceleration, or even your transmission shifting. In some cases, it can cause your transmission to go into limp mode. You may also notice an increase in engine vibrations.

What causes a Mercedes Benz engine to not start?

Engine Cranks but no Start, Dies, Stalls, or Backfires. A failed crankshaft position sensor can cause your engine to stall or not start at all. Your Mercedes-Benz may start and run for a short time, or until it gets warm and then it dies.

How to change the crankshaft position on a Mercedes Benz?

Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. This opens in a new window. Remove bolt. Remove the crankshaft position sensor. You will have either an E8 or E10 bolt that holds the CPS sensor in place.

Where was the 2002 Mercedes-Benz C240 sedan made?

The 2002 C240s were made in both Germany and in Brazil. I was alarmed one day when a friend showed me the plate in the car stating it was manufactued in Brazil. He was having a lot of problems with the vehicle. I couldn’t understand why, because I have the same car and he bought his on my recommendation.

Is the Mercedes Benz C240 in good condition?

2003 Mercedes Benz W203 C240SedanWhite in colour250k+- on the clockSunroofLeather interior AutomaticRadioElectric seatsPowerpipesElectric windowsRecently serviced (Feb 2021 full service)Spare wheel2 owner vechileLicense disc up to dateAll paperwork in orderV6 2.6 engineAccidental freeDrives very smoothStart and go Very good condition.

What to do when your Mercedes goes into limp mode?

You may also get a check engine light if your transmission goes into limp mode. When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level.

How much does a Mercedes C class C240 cost?

WRONG! then (no warranty) due to the tranny problem (or visa versa) the torque converter and radiator went bad: $3500 2 catalepsy converters: $1100 ea 2 alternators: $1000ea 2 mass airflow intakes: $900ea 5 SETS OF TIRES AND 4 BREAK JOBS (with rotors), they don’t give us enough room to list all failures Was this review helpful? (43) (14)

Are there any problems with a Mercedes C class?

Spark plug wires defective recommeded fix $1500. Defective Lower front control arms fix $750. These are not routine maintenance issues but defective manufacturing which I do not expect on a $40,000 german car. Pls do not buy Mercedese if they are not able to guarantee defective products in their vehicles. Was this review helpful? (22) (0)

Where to find Mercedes-Benz transmission code p0715?

As you can see by the chart below, code P0715 has four subgroups. Without a professional grade scanner to read the manufacturer’s precise code (to the left of any P0715 code) it is pure guess work. The first thing to check is the 13 pin connector on the passenger side of the transmission.

Is there an AAMCO code for a 2002 C240?

I had the same problem with my 2002 C240 (code P0715) I took the car to AAMCO and they replaced my TCM, harness and trans oil all for $1000. The car was running fine untill a few more months later I’m back to being in “Limp Mood” I have no idea what to do next!

Can a Mercedes-Benz ML320 read fault p0715?

My ML320 read the same fault P0715 with a new Conductor plate with new sensors. may be someone can help. As you can see by the chart below, code P0715 has four subgroups. Without a professional grade scanner to read the manufacturer’s precise code (to the left of any P0715 code) it is pure guess work.

What is the fault code for Mercedes C class?

Common fault codes: P1856 – Selector Lever Position Detection Failed; P240C – CAN Signal Selector Lever Position N15/5 Is Not Plausible Affected Vehicles: Mercedes A-Class 2004 – 2012 (W169) Mercedes C-Class 2005 – 2009 (W203 and pre-facelift W204) Mercedes CLK 2005 – 2009 (C209/A209) Mercedes CLS 2005 – 2009 (W219)

Why is my gear selector not working on my Mercedes C-class?

The C-Class W203 and pre-facelift W204 has a common fault with the automatic gear selector module / gear lever. This gear selector will cause problems preventing selection of any forward or reverse gears until the ignition is cycled. The gear selector position will not be recognised on the gear display or will show incorrectly.

What happens when the gear selector does not work?

The gear selector position will not be recognised on the gear display or will show incorrectly. If the vehicle is in gear when the gear selector module fails you will find that you are not able to select park (P), again until the ignition is cycled.

What is the fault code for a D2B ring?

N1141 MCS fault code: Set-actual configuration of D2B ring differs from actual. N1241 CD fault, CD can not be read. 9260 SRS: resistance in drivers airbag too high. Replace Wiring. Please post a link to this string of posts in the Useful W163 Documents and the DIY Stickys at the top of this forum. done. good stuff.. Anyone know anything about it?

What are the fault codes for a fuel pump?

P0230 Fuel Pump Primary Circuit Malfunction P0231 Fuel Pump Secondary Circuit Low P0232 Fuel Pump Secondary Circuit High P0233 Fuel Pump Secondary Circuit Intermittent

Do you need dipstick to check Mercedes transmission?

The car doesn’t come with a dipstick to check the transmission level but you can order one online for under $20. You will need Dipstick Tool for 722.6 722.9 Mercedes-Benz Transmission for measuring fluid level. Watch the video below to learn how to check the transmission fluid level on your Mercedes-Benz.

How can you tell if your transmission fluid is overfilled?

The transmission will have to wait for these unlubricated parts to engage before shifting the gear. One of the telltale signs of an overfilled transmission fluid is the presence of a puddle underneath the transmission. The fluid often has a reddish color. This will help differentiate it from other types of automotive leaks.

What are the most common Mercedes Benz transmission problems?

Top 5 Mercedes-Benz Transmission Problems. Won’t come out of Park gear due to a defective brake light switch. ( DIY How to replace the Brake Light Switch) Continue to read if you would like to learn how to troubleshoot your Mercedes-Benz transmission yourself and where you should start. 1. Check Fluid Level

What to do if your transmission is slipping?

Using the wrong transmission fluid will ruin your transmission. If the fluid is below the ‘Add’ mark, you need to refill it with the specific fluid for your car. Use a funnel to refill the transmission fluid to the recommended level. After this fix, check for transmission slipping again.

What causes transmission fluid to slip in a car?

Here again the importance of transmission fluid becomes obvious. Take care of your transmission fluid and you’ve won half the battle against transmission wear and expensive breakdowns. Clutch wear can cause manual and automatic transmissions to slip. Automatic and manual transmissions both make use of clutches, but…

When to change the fluid in a transmission?

If the fluid level is low, but the color seems fine, you should first try to fill it up. If it is brown, you want to consider changing the fluid and the filter. If the fluid is black and smells burnt, you definitely want to change it and make a transmission flush.

What is the fault code for a Mercedes heater?

P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1) P0136 O2 Sensor Circuit Malfunction (Bank 1 Sensor 2) P0137 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2)

Where to find Mercedes check engine light codes?

1. Connect scan tool to the 16-pin data link connector (DLC) 2. Turn the ignition On. 3. Follow scan tool manufacturer’s operating instructions to retrieve the Diagnostic Trouble Codes (DTC’s). Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions of all other Mercedes check engine light codes.

What is fault code b1859 on Mercedes Benz?

There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.

What does a check engine light mean on a Mercedes C230?

A check engine light can indicate a broad spectrum of problems with your 2007 Mercedes-Benz C230. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.

Is there a check engine light on a 2003 CLK320?

2003 clk320: check engine light..circuit 87 voltage too low could you… i have a 2003 clk320… Submitted: 9 years ago. Category: Mercedes Experience: Bosch Certified Master Tech. Over 35 years experience. Hi, what module did you retrieve that code from? And what is the problem with the car? The only P2600 I can find is in the transmission control.

Navigation