Is the power window on the passenger side?
Power window works on driver side but not on passenger side power window works on driver side but not on passenger side replaced motor still doesn’t work all 3 window switch are the same and work on drivers side …
Why is my driver’s side window not working?
The driver’s side window motor may have gone out, or there should be a short or bad connection in the switch. You could try taking the door card off and inspecting the window switch connector. I’ve had luck in the past just unplugging and plugging it back in when my passenger window was working intermittently.
What causes a GMC power window to move?
The passenger side switch is the probable cause. The driver’s side switch uses the relays in the passenger switch to operate the window and if this is defective a good driver’s side switch will not cause the window to move. Replacing the passenger side switch should fix the problem.
How can I control the passenger side window?
Then pull up on the switch to roll the window all the way up, and keep the switch up for an additional 3 seconds. Following this reset, the driver’s switches were able to command the passenger side window once again.
Why is my drivers side power window not working?
I suspect the relay has failed or the master power window switch, which provides the ground to the control side of the power window relay, has failed. You’ll need to check the relay and the relay terminals. The problem could be the relay, the master power window switch or the ground to the power window master switch.
What to do if your passenger side window is not working?
If it’s the passenger window that is malfunctioning, you can test the switch by using the driver side window controls. If it works using those controls, you will need to replace that window switch. If it’s the driver side window that’s not working, you’ll need to swap out the controls to test it.
Why does my driver side door lock not work?
The windows and the locks are on two separate circuits. The only part that these two have in common is the master switch. Of course it is also possible that the wiring harness between the driver side door and cowl is corroded and that some of the pins are to corroded or even broken off and do not make contact.
Why is my master power window not working?
If there is no power on fuses 24-26 then the power window relay is not powering on and that will cause the symptoms you describe. Notice I didn’t say the relay failed because the relay is controlled by the door multiplex control unit inside the master power window switch so it could be a bad relay or a bad power window switch.
What causes a power window to not go down?
There are a number of things that could be causing a malfunction of your power window. First off, is it only one window that won’t go down? If so, it might be a single connection, switch, or motor that’s not working. If all power windows aren’t working, then it might be a fuse or relay.
Why is my power window not working on my Oldsmobile Intrigue?
The problem is likely to be a bad connection at the fuse box or ignition switch. What would cause no power to the rear right window of a 2000 Oldsmobile Intrigue? GMC power window troubleshooting for this problem will require a voltmeter. On the switch for this window, check for battery voltage at the purple and light green wires.
What to do if your power window is not working?
Begin working on the window of the driver’s side of the car. Hold down the window switch and listen for the noise of the motor. If you do not hear a noise, the window switch, regulator, motor or wiring is damaged. To figure out the problem, you will need to take off the door panel.
Why are the power windows on my Ford Mustang not working?
Its a 3.8 convertable and the power windows don’t work. At first if you wiggled the master window switch assembly it would work. Now it totally gave out, not even the passenger side window switch works. I figured it was the master window switch and replaced it with a OE unit from Ford, but still doesn’t work.
How long does it take to troubleshoot a Ford power window?
Troubleshooting most Ford electric windows will take the average weekend mechanic about an hour. Check the fuses for burned out filaments by pulling the appropriate fuse and viewing it.
Why are my Silverado windows not going down?
I purchased a 1991 Silverado for my son and the windows worked fine for a month and then they started to stop and go at times. I replaced the switches and checked the relay and all were fine. I then took the panel apart and it looks like the previous owner made speaker holes in them and damaged some of the wires in the process.
Why is my front passenger window not working?
Front passenger window not working, not getting power to the switch either. The other three windows work great. Which color is the power for the passenger side? Where do I start? have the same problem?
What happens when a power window switch fails?
Window works from master switch only In some cases the window may not work from its own switch, but the master switch can still put the window up or down. In this case there is a good chance that the power window switch has failed and that the other window components are working properly. 4. Windows work sometimes
Power window works on driver side but not on passenger side power window works on driver side but not on passenger side replaced motor still doesn’t work all 3 window switch are the same and work on drivers side …
The passenger side switch is the probable cause. The driver’s side switch uses the relays in the passenger switch to operate the window and if this is defective a good driver’s side switch will not cause the window to move. Replacing the passenger side switch should fix the problem.
How to reset the power window control unit?
Move the driver’s (or the front passenger’s) window all the way down by using the drivers (or the front passenger’s) window DOWN switch 12. Pull up and hold the driver’s (or the front passenger’s) window UP switch until the window reaches the fully closed position, then continue to hold the switch for 1 second 13.
Why does my power window not move up or down?
1) Bad Window Regulators The mechanism that allows a power window to move up and down is called a window regulator. Each car door with a power window has a window regulator to move it. If the regulator goes bad, then pushing the up or down button will not make the window move.
Is there a problem with the passenger side window switch?
I have noticed a problem with my passenger side window switch. It will roll the window down, but it won’t roll the window back up. I can only roll the window back up using the switch on the driver’s side. In the past, I have taken the trim off of both doors to work on the speakers and apply some Dynamat.
How does the power window on the passenger side work?
Therefore, the windows should go up and down without any input from the drivers side controls. When the window is lowered from the drivers side, power is sent through the switch on the passenger side door to lower the window. Since the window will not go down from from the passenger side, the place to check is there.
Front passenger window not working, not getting power to the switch either. The other three windows work great. Which color is the power for the passenger side? Where do I start? have the same problem?
How is the window lowered from the drivers side?
When the window is lowered from the drivers side, power is sent through the switch on the passenger side door to lower the window. Since the window will not go down from from the passenger side, the place to check is there. The window motor only has two wires because power will flow through one wire to raise the window.
Where are the power window switches located on a car?
The switches are located near each window, with a master panel on or near the driver’s door. Over time, the fuse, motor, or regulator can go bad and need to be replaced.
1) Bad Window Regulators The mechanism that allows a power window to move up and down is called a window regulator. Each car door with a power window has a window regulator to move it. If the regulator goes bad, then pushing the up or down button will not make the window move.
Why is my power window not working after an oil change?
Cycle the lockout button on the driver’s side window switch which should have all windows working. The mechanics might have pressed the switch inadvertently. Power window operation has no connection with the oil change.
Why is my Honda Civic power window not working?
Click to expand… Make sure you do not have the “Window Lock” switch enabled in the driver side window control panel. Also, make sure that the 20A fuse is not blown, its located in the underdash fuse box.
What causes a power window to not work?
When you have a power window not working condition, most DIYers automatically suspect a bad power window motor. That’s usually not the case. If you have a power window not working issue, the fault is usually a broken window regulator, bad window switch, or a problem in the power window wiring. Passenger window not working
Why is my passenger window not working but the driver window is working?
When passenger windows don’t work, but the driver’s window does, chances are high that you’ve got a bad master switch in the driver’s door or a broken wire in the driver’s door hinge area. Second: Power window motors only have two wires.
Why does the passenger side window not work?
The red / light blue is a different story. That is the 12-volt feed only for when the passenger switch is pressed. It is not used when the driver’s switch is pressed. This is why I suspect you have two problems, since the window doesn’t work from either switch.
When you have a power window not working condition, most DIYers automatically suspect a bad power window motor. That’s usually not the case. If you have a power window not working issue, the fault is usually a broken window regulator, bad window switch, or a problem in the power window wiring. Passenger window not working
What does it mean when your driver’s window is not working?
First: All the wiring for driver’s and passenger’s windows runs through the master switch. When passenger windows don’t work, but the driver’s window does, chances are high that you’ve got a bad master switch in the driver’s door or a broken wire in the driver’s door hinge area.
How many volts does the passenger side window have?
So, the white / yellow and the tan / light blue will have 0 volts with both switches released, as you found. The red / light blue is a different story. That is the 12-volt feed only for when the passenger switch is pressed. It is not used when the driver’s switch is pressed.
What should I do if my power window is not working?
If no voltage is detected on any or some of the wires, the wiring in the door jamb should be wiggled while the voltage is monitored to see if the is a fluctuation. If there is, it indicates broken or loose connections in the door jamb. Check for this and replace or fix as required.
There are a number of things that could be causing a malfunction of your power window. First off, is it only one window that won’t go down? If so, it might be a single connection, switch, or motor that’s not working. If all power windows aren’t working, then it might be a fuse or relay.
What to do if your elictric window won’t go down?
If you take it apart, you may find that there are 3 disintegrated nylon plugs that have deteriorated between the plastic gear and drive gear. If they have gone bad, you can replace them with new plugs found at NAPA (about $8. I think they are only listed for fords, but they aren’t rocket science.
Why are my left and right turn signals not working?
Replace any bulbs that are not lit. The flasher unit is used to switch the current on and off for both right and left directionals. If the turn signals are inoperative in both directions, a defective flasher unit or blown fuse is the usual cause.
What does it mean if your passenger side window switch has failed?
It means that the passenger side window switch has failed. The fact that the drivers switch operates the window properly lets you know that the window components all function properly as that the problem is probably electrical.
Where is the fuse on a Ford power window?
Most Fords will have transparent fuses, and the filament can be checked with a bright light or in sunlight. Many Fords come with a fuse puller located in the interior fuse block cover. This small puller is a simple pair of clips that grab the edges of a blade-style fuse.
When passenger windows don’t work, but the driver’s window does, chances are high that you’ve got a bad master switch in the driver’s door or a broken wire in the driver’s door hinge area. Second: Power window motors only have two wires.
Most Fords will have transparent fuses, and the filament can be checked with a bright light or in sunlight. Many Fords come with a fuse puller located in the interior fuse block cover. This small puller is a simple pair of clips that grab the edges of a blade-style fuse.
What would cause the power windows from not working?
Common Causes of Power Windows Not Working Bad Window Regulators The mechanism that allows a power window to move up and down is called a window regulator. Bad Window Motor Every power window requires a window motor to supply the electrical energy. Snow and Ice If you live in a region with a lot of snowy and icy conditions, this could compromise the functionality of your power windows.
Why is my power window not working?
Power windows can stop working without warning. The most common cause of this is because their regulators and motors are used more often than other features of the vehicle. If your power windows have stop working, have them checked out by a mechanic as this is a safety issue.
How do you fix a stuck car window?
Follow this procedure to fix sticking car windows: 1) Roll the window all the way down. 2) Spray the silicone lubricant between the rubber channel. 3) Roll the window back up. 4) spray the silicone lubricate on the edges of the seal. 5) Wipe the excess lubricant. All Done! Scotty Kilmer explains it well in this video:
How do you repair an electric car window?
Follow these steps to repair an electrical issue with your car’s windows: Locate and check the fuse for the problematic window motor. If it’s blown, replace the fuse. Remove the door panel. Locate the securing screws, usually behind covers or trim, and undo them.
Where are the side windows on a car?
These auto glass panes are located on the sides of the vehicle in the doors. Side windows can take many shapes and sizes and either sliding or stationary. Most modern cars have an electric motor that “rolls” the window pane up and down, using a switch controlled by the passenger.
How does a car window roll up or down?
Most modern cars have an electric motor that “rolls” the window pane up and down, using a switch controlled by the passenger. Older cars required a crank to roll down the window and only the driver and front passenger windows would roll fully into the door of the car. What type of glass is used in car windows?
Why does my car window keep getting stuck?
Unfortunately, when it rains while the windows are left down, the switches are usually the first recipient of rainwater, which can collect in the switches and ruin them. Holding the window switch up while opening and slamming the car door may jar the motor and get it to bump into the next contact in the armature.
What kind of truck has windows that roll down but not up?
The Chevrolet Silverado is a line of trucks under the Chevrolet brand and manufactured by General Motors. Mechanically, the GMC Sierra and Chevrolet Silverado are identical. I have a problem with my power windows. They all roll down using the driver door or their own switch but the only one that rolls up is the driver window.
What to do if your Nissan power window is not working?
Nissan has issued a service bulletin to address Nissan power window problems where the power windows may not work properly after the vehicle’s battery has been disconnected or a window fuse blows. Do NOT replace the window regulator or window controller. The Nissan power window problems can be corrected by performing a re-initialization process.
Why does my Honda front window not go down?
If the windows move in one direction the problem is not the motors it is the wiring or lack of a ground or power because of the switch. Was this answer helpful? I have a 2004 Honda CRV passenger front window goes up won’t go down.
Nissan has issued a service bulletin to address Nissan power window problems where the power windows may not work properly after the vehicle’s battery has been disconnected or a window fuse blows. Do NOT replace the window regulator or window controller. The Nissan power window problems can be corrected by performing a re-initialization process.
What should I do if my car window won’t roll up?
A quick way to determine if the problem is electrical or mechanical is to push the switch up and down and listen closely. If you can hear the motor making a noise, the problem is probably a mechanical problem. If this is the case, chances are it’s the window regulator. Most power windows use a cable or plastic strap to drive the window up and down.
If no voltage is detected on any or some of the wires, the wiring in the door jamb should be wiggled while the voltage is monitored to see if the is a fluctuation. If there is, it indicates broken or loose connections in the door jamb. Check for this and replace or fix as required.
The problem is likely to be a bad connection at the fuse box or ignition switch. What would cause no power to the rear right window of a 2000 Oldsmobile Intrigue? GMC power window troubleshooting for this problem will require a voltmeter. On the switch for this window, check for battery voltage at the purple and light green wires.