What causes a bad ignition switch on a Jeep Commander?
Your symptoms could be a bad ignition switch or it could be this common problem as well. The earlier Commanders had a common problem with the terminals on the starter motor, where the cables/wires connected.
When did my Jeep Grand Cherokee ignition fail?
The contact owns a 2008 Jeep Grand Cherokee. While driving 45 mph, the engine seized and shut off. The contact was able to park the vehicle on the side of the road and restart it with no issue. The contact stated she experienced the failure again on July 12, 2019.
Is there a problem with the ignition switch?
Have had the ignition switch recall performed and also have had the new ignition switch replaced twice but problem continues. Very dangerous situation to drive at night with unreliable lights. After turning off engine, key fob is seized in ignition switch, but releases after period of time.
Where is the ignition switch on a 2005 Jeep Grand Cherokee?
The contact owns a 2005 Jeep Grand Cherokee. While driving various speeds, the vehicle would suddenly shut off. The vehicle was taken to the local dealer (DE cozen Chrysler/Jeep in verona, NJ) where it was diagnosed that the ignition switch was faulty.
Is there a recall on a 2008 commander?
I have a 2008 Commander that is part of the p57 recall for the ignition switch (9/2014). The switch has totally failed (2/2015). Called all the dealers in my area and nobody has received the parts yet. Called Jeep they have no update on when parts are going to be available.
Are there any problems with the Jeep Commander?
Also please check out the statistics and reliability analysis of Jeep Commander based on all problems reported for the Commander. Ignition problem . . Dealer replaced ignition due a recall on vehicle, but the problem was not fixed.
What are the symptoms of an ignition switch failure?
The initial symptom was a slow starter. Occasionally, when I turned the key, the starter wouldn’t engage. Turning the key again would fix this problem. In the past few days, however, more serious symptoms have appeared. When I turn the key, the car will turn over fine, but the electronics will be in accessory mode.
Your symptoms could be a bad ignition switch or it could be this common problem as well. The earlier Commanders had a common problem with the terminals on the starter motor, where the cables/wires connected.
Are there any problems with the Jeep Grand Cherokee ignition?
The ignition switch was replaced and the drive control module was reprogrammed however, the failure persisted. The manufacturer was notified of the failure. The failure mileage was 200,000. See all problems of the 2005 Jeep Grand Cherokee .
What happens if the ignition control module fails?
by Dan Ferrell. A failing ignition control module can be a real headache at times. It can produce a wide range of engine performance problems, including preventing the engine from starting or stalling the engine as you speed down the road, just to let you resume your driving a few minutes later, as if nothing had happened.
Where was the Jeep Grand Cherokee ignition switch replaced?
The vehicle was taken to the local dealer mountain view Chrysler located at 6276 alabama hwy, ringgold, GA 30736, who diagnosed that the ignition switch was defective. The ignition switch was replaced and the drive control module was reprogrammed however, the failure persisted.
Are there any problems with the Jeep Grand Cherokee ignition module?
See all problems of the 2005 Jeep Grand Cherokee . Ignition module problem vehicle runs without key in ignition. Reference: NHTSA campaign number: 10v200000 while driving, if the vehicle goes over a bump in the road the key fob may fall out of the ignition module.
What happens if you have a bad ignition control module?
A faulty ignition control module can cause a number of problems. 1. Check engine light is on: The ECM monitors all parts of the vehicle that could affect emissions. This includes the ignition system. If it determines the ignition module has caused a problem with the system, it will turn on the check engine light.
The vehicle was taken to the local dealer mountain view Chrysler located at 6276 alabama hwy, ringgold, GA 30736, who diagnosed that the ignition switch was defective. The ignition switch was replaced and the drive control module was reprogrammed however, the failure persisted.
Can a faulty ignition lock cylinder cause problems?
When the ignition lock cylinder has issues it can cause problems with powering on and starting the vehicle. Usually a faulty ignition lock cylinder will produce a few symptoms that can alert the driver of a potential issue.