When to tighten torque settings on Jeep Wrangler?
As a part of routine maintenance or anytime that you work on your Jeep JK Wrangler, it is important that you tighten any bolt and/or nut that gets removed back to the appropriate torque settings as is outlined by the Factory Service Manual.
How much torque does a Wrangler YJ engine have?
4.0L & 4.2L Engine Torque Specs Description Specification Camshaft Sprocket Bolt 50 ft-lbs Crankshaft Pulley To Vibration Dampener 20 ft-lbs Cylinder Head Bolts 4.2L 85 ft-lbs Cylinder Head Bolts 4.0L First 22 Then 45 Then 45 Then 100 ft-lbs
When to change timing belt on Jeep 2.4L?
The previous bulletin should be removed from your files. The latest bulletin applies to vehicles equipped with a 2.4L engine built between Feb. 1, 2004 and April 5, 2005. Whenever re-torqueing the cylinder head bolt (s), be sure to follow the torque sequence as outlined below.
What are the brake parts on a JK Wrangler?
BRAKE COMPONENTS DESCRIPTION N·m Ft. Lbs. In. Lbs. Rear Caliper Adapter Mounting Bolts 35 26 220 Front Caliper Brake Hose Banjo Bolt 31 23 — Rear Caliper Brake Hose Banjo Bolt 31 23 — Front Caliper adapter 163 120 —
As a part of routine maintenance or anytime that you work on your Jeep JK Wrangler, it is important that you tighten any bolt and/or nut that gets removed back to the appropriate torque settings as is outlined by the Factory Service Manual.
What kind of bolts are in a Jeep Wrangler?
Type: 31.18 YJ – FRONT Brake Hose to Caliper Banjo (Hollow) Bolt Type: Bolt 20.34 YJ – Brake Master Cylinder Mounting Nuts Type: 7.5 10.17 YJ – REAR Wheel Cylinder Mounting Bolts Type: Bolt
What are the torque specs on a TJ Wrangler?
All TJ Wranglers other than Rubicon models came standard with a Dana 30 front axle. These torque specs come in handy if you are changing differential fluid, rebuilding the axle, or regearing. These specs only apply for the front Dana 44 axle for TJ Wranglers.
What kind of front axle does TJ Wrangler use?
Dana 44 front axles came standard on Rubicon models, it was not available for any other models. The 194 RBI is also called the Dana 35 and came standard in all TJ Wranglers other than the Rubicon. Note: Refer to pinion gear removal and installation procedures for proper pinion nut tightening instructions.
Where can I get torque for my Jeep Wrangler?
Find the aftermarket Wrangler parts you need, at ExtremeTerrain. Remember to torque your Wranlger’s bolts after every modification! When your Wrangler rolled off the factory assembly line, every single nut and bolt of the steering, drivetrain, suspension, and many other areas, were torqued to manufacturer’s specification.
Why did my torque nut snap on my Jeep Wrangler?
If the bolts were over-tightened they could get stuck in the hole, snap, or pull the threads out. During routine maintenance and after doing any kind of modification to your steering, suspension, or drivetrain, all bolts and nuts should be checked to ensure that they have been tightened to specification.
What kind of bolts do Jeep Wrangler use?
Keep this in mind when shopping for replacement bolts. Black oxide, chrome, and zinc plate, once they begin to rust and it gets into the threading of the bolt holes, it eats away at the tub. So why did we choose allen head over torx… Torx/Star bolts on Jeeps strip easily because of how shallow they are.
What are torque specs for steering and suspension?
The torque specs of your steering and suspension system are extremely important. If these components are not correctly torqued to spec you run the risk of shimmy, death wobble, or even loss of control while driving.
What are the parts of a Jeep Wrangler?
Below is an example of an exploded image diagram for Jeep CJ Dash Parts, showing the breakout of Jeep Wrangler body parts diagram that make up the dash assembly. Our exploded image diagrams page has detailed images of Jeep parts including axle parts, brake parts, jeep 4.0 engine diagrams, suspension parts, transmission parts and more.
Where is the fuel pump sprocket located on a JK Wrangler?
Four-Door Second Row Center or Left Seat Belt Buckle Anchor Plate Mounting Nut Ft. Lbs. Crankshaft Main Bearing Cap Cross Bolts (3.8L) Ft. Lbs. Ft. Lbs. High Pressure Fuel Pump Sprocket.
What kind of bolts do JK Wrangler use?
We sell High Grade 18-8 Hardened Corrosion/Rust Proof Stainless Steel. This is why 1000’s of Jeepers, contractors, and mechanic shops trust us worldwide. Plus, we guarantee all our bolts – any bolts that rust, corrode, oxidizes, or strip, we will replace for free as long as the original owner has the Jeep.
Why are the bolts on Jeep Wrangler so shallow?
Torx/Star bolts on Jeeps strip easily because of how shallow they are. Torx bits get narrower from the beginning of the bit to the end, similar to a drill bit. They need more depth to grab the bolt head surface and cannot properly accomplish this on a flat bolt.
Where do you get your Jeep bolts from?
We are based in Colorado Springs, Colorado. Every bolt order is hand packaged and shipped from the Rocky Mountain Front Range with your name on it. At JeepBolts.com this is what we do. Such a small item on these vehicles rusts out in most areas of the country, and this, in turn, leads to a depreciated resale value that can be thousands of dollars.
What kind of steel is used in Jeep bolts?
– There are a large number of variations in steel. Grade of stainless steel, Passivated, NonPassivated, hardened, how the steel is annealed, does it meet ASTM standards, is it stainless or automotive-grade – automotive-grade steel still rusts.
Is there a way to reset the throttle body?
This method is almost foolproof as long as all ECU control parameters are within their normal ranges. Resetting The Throttle Body Calibration (this step is conditional) A Rough Idle or a SES can sometimes be caused by a change in the throttle body position sensor calibration.
What’s the problem with the throttle on a jeep?
I went back and they said that the throttle position sensor faulty and the entire throttle body needed to be replaced. So, they ordered one and installed it. They then told me that when they tested it, the computer said that it was only at 75% throttle when they were in fact giving it full throttle.
Four-Door Second Row Center or Left Seat Belt Buckle Anchor Plate Mounting Nut Ft. Lbs. Crankshaft Main Bearing Cap Cross Bolts (3.8L) Ft. Lbs. Ft. Lbs. High Pressure Fuel Pump Sprocket.
How can I Fix my throttle control problem?
The dealer replaced the throttle body and throttle position sensor, the powertrain control module, and the gas pedal assembly and sensor. NONE of these repairs fixed the problem. I got tire of them not being able to solve the problem so I started looking at things myself.