Why is my turn signal on on my Dyna Glide?
Diagnosing and clearing the codes on each module is really simple, as explained below. Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse.
Can a dyno flash be used on an ECU?
Most people do both… Fueling can be done on the ECU if the dyno operator has the software. If not you need a fuel controller (Bazzaz/Power Commander) You can have a generic tune put on the ECU when flashed but its not necessary if you are getting a custom tune.
Why are my turn signals not flashing on my Harley Davidson?
If you are stuck with having to manually cancel the turn signals, the problem could be found in connectivity to the speedometer or the TSSM. Check the switches. Check for loose or disconnected wires to the speedometer. Check the tip switch that cancels if the bike falls over.
Why is my hazard light not working on my Harley?
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
What are the symptoms of a bad turn signal Flasher?
1. Turn signals or hazards do not function. The most common symptom of a bad or failing turn signal / hazard flasher is hazards or turn signal lights that do not function. If the flasher breaks or has any internal issues it can cause the lights to malfunction, or not respond at all when the turn signal lever or hazard light button are pressed.
Most people do both… Fueling can be done on the ECU if the dyno operator has the software. If not you need a fuel controller (Bazzaz/Power Commander) You can have a generic tune put on the ECU when flashed but its not necessary if you are getting a custom tune.
Can a dyno be used to tune a Harley Davidson?
A Harley has two cylinders. The air/fuel ratio (AFR) needs to be measured and tuned in both so if the dyno has: No AFR sniffer – it’s only useful for maximum horsepower and torque measurement. It CANNOT be used to tune fuel injection and may only be a prop for a ripoff scheme.
What does dr.dyno want from a Harley Davidson?
When a Harley comes off the Doc’s dyno, he wants you to have: Silky smooth power at all throttle openings. Good fuel mileage, typically 42-45 at reasonable highway speeds. Very little or no decel pop. Cool running at low speeds. But what if you can’t hook up with the Doc to get your Harley all dialed in?
Why are the turn signals on my Harley not working?
2) If you have LED type bulbs, someone replaced the turnsignals BEFORE you and may not have added the recommended load equilizer (simulates load of filament type bulbs), and never got the problem fixed just right, and if left alone it can “fry” the TSM/TSSM. Hopefully you have not gotton to this point and have to replace the module.
What to do when your turn signal doesn’t work?
Turn the ignition to run/stop in run position with ignition off. Hold ODO reset button in and hold. Turn ignition switch to IGN. Release ODO reset button. Background should light up, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should all light up.
Why are the lights on my Road Glide not working?
Turn signals work just fine, all the fuses are good, bulbs are good, no disconnected wires inside the fairing. Can’t finda ny disconnected wires anywhere – any thoughts on where to look? Double check the fuse labeled “lights” in position 19 in the fuse box. The brake and turn signals runoff a different fuse.
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
Why are my turn signals not working on my Harley Davidson?
Changes in temperature, moisture and dust are some of the factors that can cause this to happen. Our bikes need some attention after spending a lonely cold winter in the garage.
Is it illegal to not have a turn signal on a bike?
It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night. A broken signal light is illegal in many states. So, don’t let this problem persist. Get those signals fixed as soon as you can.
Where is the turn signal module on a Street Glide?
Jonathan, sounds like you have a bad turn signal module. You will find this module between the fuel tanks, beneath your dash area. Thanks, and good luck Similar Question Been enjoying the videos and tips I have a 2008 Street glide with 90K miles on it. I always took it to the dealer until I found your website and got the premium membership.
Why is the right turn signal light not working?
The right turn signal light and the neutral light does not light. What do you call these indicators lights and where can you get them? Hi William. Those are, simply, indicator lights. They are sealed. There are no bulbs to change for the indicators on your year/model. Usually, when one fails, however, it is due to a bad connection or switch.
How do you reset the turn signal on a Harley Davidson?
Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.
How do you reset the turn signal on a Dyna Glide?
Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.
Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.
Is there a problem with my Street Glide radio?
No problem accept the amp blocks my antenna reception. I use Bluetooth from phone or an SD card anyway. If your amp isn’t set right you could be blowing the speakers. Hertz are a good replacement for the fairing. Your symptoms are typical of the factory H-K radio failing.
Diagnosing and clearing the codes on each module is really simple, as explained below. Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse.
Why do some of my Harley Davidson lights burn out?
Harley’s have a bad reputation when it comes to electrical problems such as bulb burn out. While this may seem like only a maintenance issue, some Harley’s bulbs have been installed improperly. Bulb burnout exposes a rider safety problem resulting from signals and brake lights malfunctioning.
Why is my turn signal not working on my Harley?
These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code. Accessing the diagnostics menu requires you to press several of the accessory switches in a very specific manner, within a short amount of time.
What are the most common problems with a Harley Davidson?
Fuel System Failures Vapor lock malfunctions, fuel injectors, and defective pressure gauges are among the most reported problems with a Harley’s fuel system. These problems can be costly and difficult to repair. Complete regular maintenance checks on the fuel system to guarantee that it’s running properly. 6. Accessories
These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code. Accessing the diagnostics menu requires you to press several of the accessory switches in a very specific manner, within a short amount of time.
Why is the start button not working on my Harley Davidson?
If you did NOT read 12 volts, you would have to go back to the TSSM and hot wire (bypass it) in order to determine where the problem was. Also testing the start button would be something to check also. The key point to remember is that the “Start Relay Control” comes from the TSSM.
Why does my Dyna FXDC bike not start?
Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.
Why are the lights on my Turn signal not working?
While they may still light up, the lights will not be able to serve their intended purpose of signaling a turn or emergency situation. These same symptoms can also be caused by electrical issues, so having the vehicle properly diagnosed is highly recommended. 3. Additional lights are not working
If you did NOT read 12 volts, you would have to go back to the TSSM and hot wire (bypass it) in order to determine where the problem was. Also testing the start button would be something to check also. The key point to remember is that the “Start Relay Control” comes from the TSSM.
Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.
Why is the odometer on my Harley Davidson not working?
The odometer mileage is displayed but does not change. The trip meter stays the same and does not change. The directionals don’t self cancel any more. All codes clear. I recently installed an amp with speakers that runs off of an ipod.
You may have a bad module or corroded/bad connections at the module or at the handlebar switch harness/ plug. If you determine that you need a turn signal module, we suggest Badlands. I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm.
Why are the turn signals on my Harley Davidson not working?
I’m not getting any power to the right side turn signals, the green arrow on the dash don’t light up on right, and turn signals are very dim and slow on left side. Wiring seems to check out, fuses ok.
The odometer mileage is displayed but does not change. The trip meter stays the same and does not change. The directionals don’t self cancel any more. All codes clear. I recently installed an amp with speakers that runs off of an ipod.
Why is the head light not flashing on my Harley Davidson?
No head light, and no tail light. After spending several hours goint through the wiring looking for a short, we discovered that both head light and tail light we burned out. Good luck. I {Heart} Hookers. If the bulbs are lighting, but not flashing, then it’s the relay or the turnsignal module.
Where is the Kill Switch on a Dyna Glide?
The kill switch is the button located on the right side of your handlebar, next to the starter button. Position it on the “run” position. Figure 1. Turn kill switch on. Press and hold the trip reset button located on the side of your speedometer. Turn the ignition key to on.
How to reset check engine on Harley Davidson Dyna Glide?
Press and hold the trip reset button located on the side of your speedometer. Turn the ignition key to on. Hold the button until the word “diag” appear on the odometer screen, which stands for diagnose. Figure 2. Hold trip button. Figure 3.
Why does my Dyna Glide fuse keep blowing?
Although a fuse will sometimes blow because of vibration or just age, it will generally point to a additional problem in the system that will need to be attended to. A fuse box diagram can be separated into three parts, which are the fuse labels, amperage rating, and maxi fuse.
Press and hold the trip reset button located on the side of your speedometer. Turn the ignition key to on. Hold the button until the word “diag” appear on the odometer screen, which stands for diagnose. Figure 2. Hold trip button. Figure 3.
The kill switch is the button located on the right side of your handlebar, next to the starter button. Position it on the “run” position. Figure 1. Turn kill switch on. Press and hold the trip reset button located on the side of your speedometer. Turn the ignition key to on.
When do I press the turn signal button, the right signal lights brightly?
The right signal lights brightly when the turn signal button is depressed, but the filiment just burns bright, there is no flashing. I have read the contacts in the bulb receptical and with the putton depressed I have 12VDC on both contacts. When I release the button (I am not holding the button down just momnetarily depressing the button.
How do you turn off lights on a bike?
This method should work with all bikes built after 2001. Move kill switch to off position, turn ignition on-off-on-off-on. Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice.
Why is the blinker on my Harley Davidson not working?
If only one light (or one side) isn’t working, check the power to the bulb plug-in connections. With a voltmeter or test light, check the terminals for power. Check the battery for a full charge. Figure 1. Multimeter. Also consider what kind of work was recently done on the bike that might have affected the blinker system.
Where does the flasher go on a Harley Davidson?
Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.
Jonathan, sounds like you have a bad turn signal module. You will find this module between the fuel tanks, beneath your dash area. Thanks, and good luck Similar Question Been enjoying the videos and tips I have a 2008 Street glide with 90K miles on it. I always took it to the dealer until I found your website and got the premium membership.
Can you start a Harley Davidson HD without a fob?
Starting your HD without a Fob! Your HD has the ability to be started without a Fob present jus in case the Fob is lost or the battery goes dead! Your Pin# to over-ride the security system is usually loaded up with the last 5 numbers of your Harley’s serial # backwards! (EX: serial # last 5 is 1 2 3 4 5……….it was entered as 5 4 3 2 1).
How to turn off the FOB on a Harley Davidson?
Here’s how to do it!! 1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual. 2. With an assigned FOB present, turn IGN key ON – OFF – ON – OFF – ON 3. Press Left turn signal switch 2 times. 4. Press Right turn signal switch one time and release.