Why is my Hyundai Santa Fe not starting?

Battery is Charged – If the battery is charged, then it would still be advisable to take a look at the battery cables and see if there is an issue with corrosion. Otherwise, it may be the starter that you need to look at. A bad alternator can cause your battery to lose enough charge to start your Santa Fe.

Why is the starter clicking on my Hyundai?

If the starter is clicking on your Hyundai, it could be the battery, or it may be the starter itself. The best-case scenario is that it’s the battery, but even if it is the starter, don’t despair. Even an inexperienced person can change the starter out in about 90 minutes.

What is the code for the Hyundai Santa Fe?

The code in the computer after failure should be P1690 or P1693 (or both). After changing the antenna piece near the ignition (180$ at the dealer), the icon shows up and car starts every time…. been around 50 times to far and no issues. Hope this helps 64 people found this helpful. this sounds so similar to whats happening with our 02 santa fe.

When does the new Hyundai Santa Fe come out?

New 2020 santafe took delivery on January 4th, 2021, with less than 5000 miles on March 21st the vehicle refuse to start after it was started and shut off while we were sitting in a parking lot. While attempting to start it getting forward collusion warning but the engine would not crank.

What are common reasons my Hyundai Santa Fe won’t start?

What are common reasons my Hyundai Santa Fe won’t start? While there are a variety of reasons your Hyundai Santa Fe won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter. 38% of the time it’s

When does a Santa Fe starter go bad?

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Santa Fe, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your Santa Fe to crank, but not start.

How to jumpstart a 2013 Hyundai Santa Fe Sport?

Safety glasses, jumper cables and a working car are needed to jump your 2013 Hyundai Santa Fe Sport 2.4L 4 Cyl.. About Us Maintenance Parts & Tools Contact English SpanishFrench Search Home Hyundai Santa Fe Sport 2013 Battery / Jumpstart How to Jumpstart a 2013-2018 Hyundai Santa Fe Sport 1.

What to do if your Santa Fe Sport doesn’t start?

If you get into your Santa Fe Sport, turn the key, and your car doesn’t start (you may hear nothing or a clicking sound from the engine bay), you have a dead battery and need a jump-start. Check to see if you left your headlights or an interior light on and turn the switch off.

Why does my 2017 Hyundai Santa Fe not start?

See all problems of the 2017 Hyundai Santa Fe . Navigation screen does not turn off after the ignition is turned causing the battery to drain and car will not start. My new 2019 Hyundai sante fe from the time I bought it had the yellow check engine light come on. It said the bsm system wasn’t working.

Is it safe to jump start a Hyundai Santa Fe?

Hyundai Santa Fe: Jump starting. Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or battery, follow the jump starting procedures. If in doubt, we strongly recommend that you have a technician or towing service jump start your vehicle. Use only a 12-volt jumper system.

What to do if your Santa Fe doesn’t start?

If you get into your Santa Fe, turn the key, and your car doesn’t start (you may hear nothing or a clicking sound from the engine bay), you have a dead battery and need a jump-start. Check to see if you left your headlights or an interior light on and turn the switch off.

Towed to the local dealer was told they cannot diagnose the car because they could not read the onboard computer, unable to say what’s wrong. The car was towed back to the dealer where purchase and was told it was a blown fuse maybe lighting strike and other theories what’s wrong.

Where are the fuse panels on a Hyundai Santa Fe?

Here you will find fuse box diagrams of Hyundai Santa Fe 2004, 2005 and 2006, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay. Information from the owner’s manuals of 2004, 2005 and 2006 is used.

When did the Hyundai Santa Fe come out?

In this article, we consider the first-generation Hyundai Santa Fe (SM), produced from 2001 to 2006. Here you will find fuse box diagrams of Hyundai Santa Fe 2004, 2005 and 2006, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

Is there any way to fix a Hyundai Santa Fe?

Total electrical failure with no recourse at the moment, Hyundai motor of America consumer affairs wants us to sign a settlement agreement to refund our expenses and have not fixed or replaced the car.

What to do if your ECM power relay is failing?

For this reason, if you suspect that your ECM power relay may be having an issue, have the vehicle inspected by a professional technician, such as one from YourMechanic, to determine if the relay should be replaced. The most popular service booked by readers of this article is Vehicle Engine Electrical Inspection.

What’s the problem with my 2008 hyundia Santa Fe?

I HAVE A 2008 HYUNDIA… I HAVE A 2008 HYUNDIA SANTA FE AND THE PROBLEM THAT I AM HAVING IS WHEN I PUSH THE KEY IN THE IGNITION THE CAR WON’T START I WOULD HAVE TO MOVE THE SHIFT FROM PARK TO DRIVE AND THEN TO PARK AND TRY THE KEY AGAIN AND IT WILL START.

What’s the name of the Hyundai that won’t start?

We have a Hyundai 2008 Sante Fe Limited Edition which will randomly not start. It turns over but will not fire. This is a random occurrence. … read more My 2010 Accent just stops while driving. The Auto repair is Customer: ***** *****, my 2010 Accent just stops while driving.

Why does my Santa Fe y2006 not start?

Hello, my Santa Fe Y2006 has this same problem. New glow plugs, currently changed crankshaft position sensor, battery in good condition, starter spins perfectly but no starting when cold (in the morning). Possible to start only after spraying of starting fluid directly to air filter outlet. Once started it will run all day with no problems.

Why does my Hyundai Elantra not start in the morning?

My Car won’t start in the cold morning. Engine rotates but does not fire. I thought something to do with oil pressure sensor connector problem, as when I spray wd40 on all connectors like air flow, oil pressure etc, it starts but again in few days it gives the same problem.

What should I do if my Hyundai engine won’t start?

Key Immobilizer faulted (unlikely unless you’re using a non-standard key or bypassed it for a remote starter or some crazy electrical nonsense). If it is this, to replace the immobilizer unit and/or keys could be around $300 or so. Crank Angle / Crank Position / Cam Angle / Cam Position sensor (s).

What causes a car to not start or crank?

An improperly adjusted or improperly operating inhibitor switch (range switch) may result in a vehicle that will not start or crank on an intermittent basis.

What makes a Hyundai Santa Fe NO start?

If the ignition switch operates properly, it operates the starter relay, which is in the engine bay fuse box and makes a little click. If that operates properly, it activates the starter solenoid, which is part of the starter and makes a clunk. Then the starter motor engages.

How often does no start no crank happen?

“No Start No Crank”. It would happen once a month or so and now it seems like it is once a day or every other day. I have 135,000 miles on it. I turn the key in park and absolutely nothing happens but the key turns. I wait a while and it starts right up. Last night after getting it out of the shop – still cant find the problem – it did it again.

When was the last time my Hyundai Santa Fe ran?

This topic contains 8 replies, has 5 voices, and was last updated by Jay 3 years, 8 months ago. I am new to this forum. I am also elderly and need a car that runs.

Why does my car not start at idle?

Consequently, no grease is leaking from your engine or transmission. The greases that are used in vehicles are found in suspension joints and CV axles and those do… Idle speed for your vehicle should be between 725 and 750 RPM. So, it is idling high. Common causes for this include vacuum leaks and a faulty idle air control (IAC) valve.

What to do when your car won’t start?

When I went to turn on the car, all power died from the car and nothing would happen when I turned the key. I wiggled the steering wheel and tried to put the car in neutral using the shift lock release and the power came back on and I was able to start it.

Why does my car not start when I put it in neutral?

Today, even putting in neutral after using the shift lock release, the car still has no power and will not start. I do not think it’s a battery issue, but now my car is stuck on the third floor the parking garage in my apartment building and I have no idea how to at least get it to turn on to take to a mechanic.

What to do if your Hyundai Santa Fe won’t start?

If you have a model of Santa Fe which only has a key fob with start/stop button and no place to insert a key, then try placing your key fob as close to the start/stop button as you can and then start the vehicle. Start/Stop button on Hyundai Santa Fe fourth generation TM Tip: You can try starting your Santa Fe with its second key.

Why does my Hyundai Elantra engine not start?

Enter your zip code: This problem started within the first 40,000 miles. Try to start, all lights come on, windows, radio, door locks work, but engine won’t crank. It might start the next attempt, or the 20th. Within minutes, or after 15. Dealer kept it 3 weeks and could not duplicate it.

What should the voltage of a Hyundai Santa Fe battery be?

The voltage of the battery on your Hyundai Santa Fe can be measured precisely with a multimeter. Before the test, the multimeter is set to the voltage range of the battery and connected to its plus and minus poles. Successful testing of the car battery, i.e. checking the voltage, usually results in values of approx. 12 to 13 volts.

How does the Hyundai Santa Fe engine work?

The system consists basically of a key which contains a programmed chip in the head of it, an antenna coil ring which goes around the ignition cylinder, and the “smartra” or immobilizer module. The way it works is you put your programmed key into the ignition and turn it to start the engine.

This topic contains 8 replies, has 5 voices, and was last updated by Jay 3 years, 8 months ago. I am new to this forum. I am also elderly and need a car that runs.

Why does my Car Crank but not start?

These vehicles are known to have problems with a no start concern where the engine will crank but not start. It almost presents itself as a possible fuel pump issue, but is actually an electrical issue related to the factory immobilizer system.

What’s the problem with my 2007 Hyundai Santa Fe?

No one has added a helpful site for this 2007 Santa Fe problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: Bought Santa Fe 2007 for our daughter who spent 6 of those years on college campus she only has 50K miles it’s on it’s 3rd transmission.

Why is the fuel filter on my Santa Fe not working?

The fuel filter of your Santa Fe does not wear out like a mechanical part, but it gets clogged by dirt and airborne particles and clogs over time. The permeability of the filter drops, and so does the fuel pressure.

Why does the battery light come on on my Hyundai Santa Fe?

The battery light comes on to indicate that the charging voltage is low. It usually means there is a problem in the car’s charging system. if the battery is in good condition, the car can still run for a short…

Why is my Hyundai Santa Fe in limp mode?

Car misfires then goes to limp mode. When the vehicle goes into limp mode when the engine misfires, the computer is shutting down the electronics to the transmission to prevent damage to the catalytic converter as the fuel condition is either too lean or too rich. Check… Hi there. The valve cover gaskets are probably worn and need replaced.

What are the problems with a 2008 Hyundai Santa Fe?

1 Fuel Level Sensor Failed 2008 Santa Fe Average Cost to Fix: $500 Average Mileage: 85,000 mi 2 Gas Gauge Not Functioning 2008 Santa Fe Average Cost to Fix: $300 Average Mileage: 80,000 mi 3 Paint Peeling 2008 Santa Fe

What kind of starter does a Hyundai Santa Fe use?

Hyundai Santa Fe Questions – The starter won’t even crank the engine. – CarGurus The starter won’t even crank the engine. I bought a new batt but that is not it.

Why does my Hyundai Santa Fe not start?

I bought a battery I have gas it’s not the starter I had a little knocking coming from the more it act like it want to start but it’s not turning over it’s making a weird nose ween u try an crank it 2015 Hyundai Santa Fe sport 1 people found this helpful.

Hyundai Santa Fe Questions – The starter won’t even crank the engine. – CarGurus The starter won’t even crank the engine. I bought a new batt but that is not it.

Why is my Hyundai Santa Fe not blowing cold air?

If you are noticing that the air conditioning is not blowing out ice cold air on the coldest settings, then it most likely needs re-gassed. If this is not the issue, then it will mean that the compressor is faulty. As mentioned above, you will most likely need to re-gas the air conditioning system to resolve this issue.

Is there a problem with the Hyundai Santa Fe?

Since we purchased our Hyundai Santa Fe brand new in May 2013, it has exhibited an ongoing and intermittent starting problem. Frustratingly Hyundai have not been able to help and the local dealership has not been able to reproduce the problem while the vehicle has been in their workshop. This short video demonstrates the problem. Loading…

Why does my Santa Fe car not start?

This is the third occassion where my 2017 Santa Fe will not start. When I turn the keys in the ignition there is no sound at all, no electricity is being sent to start the engine. However, all my lights and radio funtions work just fine. After a while the it will work again.

What kind of engine does the Hyundai Santa Fe have?

The crankshaft position sensor failure affected quite a few engines in the Santa Fe lineup, including Hyundai’s 2.0-liter four-cylinder, 2.4-liter four-cylinder turbo, 2.7-liter V6, 3.3-liter V6, and 3.5-liter V6 engines. The problem occurred at an average mileage of 103,710 miles.

How big was the fire in the Hyundai Santa Fe?

By the time the fire department arrived, the vehicle was totally engulfed in flames, which reached almost 10 feet high. The fire fighters were able to contain the fire before it reached the fuel tank, but the vehicle and its contents were totally burned. The vehicle was a shell of metal and ash when it was towed away.

How do you clean a Hyundai Santa Fe battery?

To clean the battery on your Hyundai Santa Fe, you have to remove the pole cables first, which requires no special knowledge, just a little concentration, as the order is very important. First remove the black cable from the negative pole. If the pole clamp is very tight, you can open it with pliers.

Why does my Hyundai Santa Fe battery keep draining?

If your Hyundai Santa Fe’s battery is draining, it’s something that’ll need addressing right away. If it is draining while your Santa Fe is off, it’s usually If your Hyundai Santa Fe’s battery is draining, it’s something that’ll need addressing right away. If it is draining while your Santa Fe is off, it’s usually caused by something t

What kind of car is 2007 Hyundai Santa Fe?

My 2007 Santa Fe has been a good workhorse for me (160K), and I’m trying to figure out what the heck is going on. Get outside to try and go somewhere today, and when I get in the car and turn the key, nothing.

What to do if your Hyundai Getz won’t start?

Check the battery and the terminal cable connections. If they look really corroded, you need to clean the battery posts and cable connectors or replace the cables and try to start the engine. Also check the starter. The solenoid attached to the top of the starter can fail, as well as the components inside.

Why does my Hyundai i20 not start up?

Most commonly this could be caused by a low/dead battery or there is no connection between the battery and starter. Check the battery and the terminal cable connections. If they look really corroded, you need to clean the battery posts and cable connectors or replace the cables and try to start the engine.

When does Hyundai Santa Fe shift from Park to drive?

Hyundai Santa Fe Car does not shift from park to drive Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

What does it mean when your Santa Fe won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your Santa Fe won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

Are there any problems with the Hyundai Santa Fe?

The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Hyundai Santa Fe based on all problems reported for the Santa Fe.

Where do I find the fault code on my Hyundai?

Connect your OBD-II scanner into the OBD-2 port under the dashboard on the driver’s side. Note: Even a $20 generic OBD-2 scanner can retrieve check engine / ECU Hyundai fault codes. Those are P-codes in the Hyundai list below.

How to check no start, no crank condition Hyundai?

Turn the ignition key to the ON position or push the Start/Stop Button two times. 2. Using the factory or enhanced scan tool, check for the DTCs listed above. Record the DTCs and description, then delete the DTCs. 3. Select the live data parameter for the “Shift Lever Switch.”

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Why does my car not start when I push the start button?

False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders.