Why is my Harley Davidson Dyna Glide not starting?

Why is my Harley Davidson Dyna Glide not starting?

If your battery voltage and connections are in good condition, but your engine is still refusing to turn over, the problem may be in the starter circuit. Perhaps the easiest place to begin is at the starter solenoid on the right side of the motorcycle.

What happens when you disconnect the battery on a Harley?

Since disconnecting the battery on my harley it wont start. Bike still has power all lights etc since disconnecting the battery on my harley it wont start. Hey there!

What should the voltage be on a Harley Davidson Dyna Glide?

Use a voltmeter to measure the available voltage at the battery. A battery that is 100% charged will have approximately 12.6 volts, whereas a battery with a 0% charge will read 11.8 volts or lower. If your battery is low, charge the battery on a setting no higher than five amps for a few hours.

Why does my Harley Davidson still have power?

Bike still has power all lights etc since disconnecting the battery on my harley it wont start. Hey there! I entered diagnostic mode on my 2018 Heritage because of a check engine light.

If your battery voltage and connections are in good condition, but your engine is still refusing to turn over, the problem may be in the starter circuit. Perhaps the easiest place to begin is at the starter solenoid on the right side of the motorcycle.

Since disconnecting the battery on my harley it wont start. Bike still has power all lights etc since disconnecting the battery on my harley it wont start. Hey there!

Bike still has power all lights etc since disconnecting the battery on my harley it wont start. Hey there! I entered diagnostic mode on my 2018 Heritage because of a check engine light.

How to start a Harley Davidson that wont start?

Insert 1 wire into the female terminal that would be #30 in the fuse panel socket. Insert the other WIRE (NOT END of 1st wire) into #87 of the fuse panel socket. 6) Make SURE bike is in NEUTRAL. 7) Turn on ignition ON and Kill switch to run. When you touch both of your installed wires together DOES bike crank./start? Click to expand…

Insert 1 wire into the female terminal that would be #30 in the fuse panel socket. Insert the other WIRE (NOT END of 1st wire) into #87 of the fuse panel socket. 6) Make SURE bike is in NEUTRAL. 7) Turn on ignition ON and Kill switch to run. When you touch both of your installed wires together DOES bike crank./start? Click to expand…

What’s the voltage on a Harley Davidson Street Glide?

It’s pretty much done this since day one with the OEM manual stating the gauge will read 13v-14.5v when running. Question: is the fluctuation to 13v at freeway speeds the regulator cutting back the voltage with the battery now fully charged at freeway speed/rpm and recharging at the 14.5-14.7 when on streets or…..?

What causes a Harley Davidson to not turn over?

If the bike does not turn over, the issue can be battery, starter, starter relay. If turns over, but no start, determine if the issue is electrical or fuel related. Check for spark.

When did I replace the battery on my Street Glide?

I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.

What to do when your Harley Davidson won’t start?

Try neutral with clutch pulled in. Also battery connections , solenoid wire. The security system lights only flash after I turn off the bike. I have the bike in neutral and I even tried pulling in the clutch a couple of times. I checked the wire to the solenoid and it had power.

Where is the starter on a Harley Davidson Dyna Glide?

Perhaps the easiest place to begin is at the starter solenoid on the right side of the motorcycle. Pull back the protective rubber boot and ensure the positive battery cable (yellow arrow) is securely tightened to the solenoid terminal.

Why does my Dyna Glide not start up?

Surprisingly, a faulty fuel gauge has caught numerous owners off-guard, and upon refilling the tank, the bike has started right up. If your bike is a carbureted model and you are not getting any fuel, chances are the carb is gummed up and the jets are not flowing any fuel. A quick disassembly and cleaning is often an easy fix. Figure 7.

What to do if your Harley won’t start?

The Harley service manual suggests to check the electrical connections at the ECM and CKP, as well as check the resistance of the ignition coil before replacing the CKP sensor. That being said, a large number of Dyna owners who have had trouble starting their bikes reported that replacing the CKP sensor immediately cured the problem.

Use a voltmeter to measure the available voltage at the battery. A battery that is 100% charged will have approximately 12.6 volts, whereas a battery with a 0% charge will read 11.8 volts or lower. If your battery is low, charge the battery on a setting no higher than five amps for a few hours.

Where is the starter relay on a Dyna Glide?

Starter solenoid electrical connections. Another component to inspect is the starter relay, which is located in the electrical fuse box underneath the side cover on the left side of the motorcycle. Relays have the potential to go bad and prevent high current from reaching the starter.

Starter solenoid electrical connections. Another component to inspect is the starter relay, which is located in the electrical fuse box underneath the side cover on the left side of the motorcycle. Relays have the potential to go bad and prevent high current from reaching the starter.

What causes a Harley Davidson not to start?

Some other ideas: 1 Problem with security module or key FOB 2 Problem with clutch safety switch, or its wiring (if bike has it) 3 Bad relay (like you said)

Who is the owner of the 2001 Harley Davidson Dyna Wide Glide?

2001 Harley Davidson FXDWG Dyna Wide Glide, origional owner, best of show custom paint by Vince Connors w/chin faring, Arlen Ness head light, SE 204 c… Reduced. All little bit old skool, a whole lotta fun.

How much does a 2001 Harley Davidson Dyna cost?

2001 Harley-Davidson® FXDWG – Dyna® Wide Glide®, New arrival 2001 Harley-Davidson® Dyna® Wide Glide® 2001 Harley-Davidson® FXDWG – Dyna® Wide Glide®, 2001 Harley-Davidson® Dyna® Wide Glide® 2001 Harley Davidson FXDWG WIDE GLIDE , , $399.00 SHIPPED TO ANY OF THE 48 STATES……..

What kind of fuel does a Dyna Wide Glide use?

Low mileage bike with extra chrome. 9,XXX miles. Non ethanol fuel always used along with fuel stabilizer. Had everything checked out by a certified me… 2001 Harley-Davidson® FXDWG – Dyna® Wide Glide®, New arrival 2001 Harley-Davidson® Dyna® Wide Glide®

Why is my Harley Davidson Ultra Classic not starting?

I have a 2010 ultra classic with ABS. It is not starting. The battery voltage is 12.75 off the battery. When I turn the main switch on, I get a drop to 12.5, and when the kill switch is turned on, I get a drop to 12.38. The self test goes out and hit the start switch with nothing – no volt drop, no starter engage, no nothing. DEAD.

When did the Harley Davidson Dyna Wide Glide come out?

1993: The Dyna Low Rider and Dyna Wide Glide are introduced, the two among the most popular Dyna models throughout the frame’s 26 year production run. 1995: Until this year, all Dynas had a 32-degree front rake, but in 1995 a more responsive 28-degree rake was introduced to the sportier Dyna models.

When was the first Harley Davidson Dyna made?

The Dyna Daytona and Dyna Super Glide debuted a year later. The first Dyna, the 1991 FXDB Sturgis Edition. 1993: The Dyna Low Rider and Dyna Wide Glide are introduced, the two among the most popular Dyna models throughout the frame’s 26 year production run.

How do you reset the turn signal on a Dyna Glide?

Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.

Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.

Why does my Dyna FXDC bike not start?

Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.

The Harley service manual suggests to check the electrical connections at the ECM and CKP, as well as check the resistance of the ignition coil before replacing the CKP sensor. That being said, a large number of Dyna owners who have had trouble starting their bikes reported that replacing the CKP sensor immediately cured the problem.

What’s the difference between dual fire and single fire on a Harley Davidson?

Dual fire and single fire. Dual fire coils send spark to both cylinders, all the time. Regardless of which cylinder is on the compression stroke. Single fire coils designate spark to only the cylinder that is on the compression stroke. Spark is delivered to one cylinder at a time. Harley Davidson Ignition Coils are known to fail.

How does a single fire coil work on a Harley Davidson?

Single fire coils designate spark to only the cylinder that is on the compression stroke. Spark is delivered to one cylinder at a time. Harley Davidson Ignition Coils are known to fail. The longevity you get from your coil may depend on usage, demand on the coil or environmental conditions.

What’s the problem with my Harley Davidson glide?

If your problem is with a Wide Glide, the problem could be the primary alignment. The 2006 and earlier models had an issue with the primary case causing an alignment issue. Remove the outer and inner primary case covers. Replace the rear bearing and race.

What to do if your Harley Davidson is not starting?

If you only have spark on the front cylinder, swap plug wires (front to rear, rear to front ). Now see if you (only) have spark on the rear cylinder. If you do not have power to the coil; Use a small jumper wire and power your coil directly from the battery. This will will bypass your harness and switches.

When do I hesitate on a Harley Davidson?

-If it starts to hesitate I accelerate and it goes away immediately till I let off and start cruising again. -I felt the hesitation every once in awhile about two weeks ago but not as bad till my 93 mile ride yesterday where it was VERY noticeable.

What does it mean if your Harley won’t start?

If that test was a “pass”, it would eliminate with 100% certainty, the starter and starter solenoid from the picture and all the associated wiring, all the way back to the fuse box. It would demonstrate that all the heavy starter grounds were OK also. Passing just that one simple test would eliminate a dozen possible items it could have been.

What’s the voltage on a Harley Davidson starter?

I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.

Why does my Harley Davidson have no spark?

If you have power to the coil, but no spark at the plugs, you are probably not getting any firing signal from the optics in the ignition module. Open up the nose cone end and see if it is just really dirty in there which can happen if the seal is leaking oil.

When did the Harley Davidson Dyna Glide come out?

1992: Harley-Davidson Dyna Wide Glide introduced. 1995: New switchgear, new frame with lowered seat height. 1998: New nine-plate clutch. 1999: Harley-Davidson Dyna Wide Glide gets new 1450cc engine. 2000: New front forks. 2001: New style seat and security system.

Which is better a Harley Davidson Street Bob or Dyna Street Glide?

In our view a Harley-Davidson Softail Standard (at £1000 less), Harley-Davidson Dyna Super Glide Custom (at £2000 less) or, particularly the Harley-Davidson Dyna Street Bob (at £3600 less) offer far better value. But, for some, only the Harley-Davidson Dyna Wide Glide will do.

Why does my Dyna hard start when hot?

You can spend a ton of money to only find the Least expensive things are the problems.. Hard starting when HOT, but the engine spins up fine, means either lack of fuel or weak, no spark. If your Dyna is EFI, your fuel pump is losing prime/pressure due to fuel line leak…look here:

What makes a Harley Dyan engine difficult to start?

Okay, so if your Harley Dyan motorcycle is older than 2005, and the engine is difficult to start, check for one OR MORE of the following possible malfunctions. 1. Fouled spark plug (s). 2. Improperly adjusted enricher valve. 3. Intake manifold air leak. 4. A plugged fuel tank filler cap. 5. Clogged carburetor fuel line. 6. Contaminated fuel system.

What to do if your Dyna bike won’t start?

Apparently, starter issues are quite common on various Dyna models, so if yours is in need of replacement, see How to Replace Starter. If you are in a bind and your starter motor is acting up, a quick tap of the solenoid with a hammer or similar small object can sometimes free the starter to start the bike.

You can spend a ton of money to only find the Least expensive things are the problems.. Hard starting when HOT, but the engine spins up fine, means either lack of fuel or weak, no spark. If your Dyna is EFI, your fuel pump is losing prime/pressure due to fuel line leak…look here:

Apparently, starter issues are quite common on various Dyna models, so if yours is in need of replacement, see How to Replace Starter. If you are in a bind and your starter motor is acting up, a quick tap of the solenoid with a hammer or similar small object can sometimes free the starter to start the bike.

When to stop for gas on a Dyna model?

Discussion in ‘ Dyna Models ‘ started by Kjay, Jun 26, 2010 . Things were fine until last week I stop to get gas after riding maybe 40 miles or so and when I was ready to go the bike won’t start.

Can you start a Harley Davidson HD without a fob?

Starting your HD without a Fob! Your HD has the ability to be started without a Fob present jus in case the Fob is lost or the battery goes dead! Your Pin# to over-ride the security system is usually loaded up with the last 5 numbers of your Harley’s serial # backwards! (EX: serial # last 5 is 1 2 3 4 5……….it was entered as 5 4 3 2 1).

How to reset the turn signal on a Harley Davidson Dyna Glide?

Press the reset button again and the display will read “PSSPt.” Press the reset button a few times until the first “S” is flashing, then press and hold it for five seconds. The error codes should now display on the odometer. Press and hold the odometer reset button for five seconds to clear each code.

Why does my Harley Davidson crank but not start?

There have been a few reports of a P1009 code – incorrect password also. It appears the turn signal and stalls or cranks but will not start. Try removing the ecm and security fuses, wait ten minutes and reinstall the fuses. This “reboots” the turn signal module and the motorcycle will then start from that point on.

If the bike does not turn over, the issue can be battery, starter, starter relay. If turns over, but no start, determine if the issue is electrical or fuel related. Check for spark.

Harley-Davidson FXDWG Dyna Wide Glide Specs Brand Harley-Davidson Model Harley-Davidson FXDWG Dyna Wide Glide Start year 1999 Year 1999

Why does my Harley Davidson not start when hot?

Found that when bike is hot, doesn’t want to start. It doesn’t stall when hot, but if I shut it off it doesn’t want to restart. So far, if I sit there and hit the start button enough it will finally fire, but concerned that one day it won’t start.

What kind of engine does a Dyna Super Glide have?

The bike is a 2003 Dyna Super Glide stock engine. Does anyone have any suggestions as to what might cause this or has it every happen to anyone else. Things were fine until last week I stop to get gas after riding maybe 40 miles or so and when I was ready to go the bike won’t start. After waiting say 15 or 20 minutes, it starts fine.

The bike is a 2003 Dyna Super Glide stock engine. Does anyone have any suggestions as to what might cause this or has it every happen to anyone else. Things were fine until last week I stop to get gas after riding maybe 40 miles or so and when I was ready to go the bike won’t start. After waiting say 15 or 20 minutes, it starts fine.

When did the Harley Davidson Dyna motorcycle come out?

Although the Dyna name itself did not come about until 1991, the origins of this line of Harley-Davidson motorcycles can be traced back two decades prior to that. The late 1960s brought forth a spike in the scene of custom motorcycles.

What was the rake of the first Harley Davidson Dyna?

Not only did the FXD Dyna Super Glide launch alongside the FXDS-CONV Dyna Glide Convertible, but these were the first Dyna models to present a 28° rake. All previous Dyna models featured a 32° rake.

Is there going to be a Harley Davidson switchback?

The Switchback, the first ever Harley-Davidson Dyna configured as a touring motorcycle from the factory. 2017: The Dyna meets its demise as Harley-Davidson unceremoniously announces that certain Dyna models will be Softails beginning in 2018.

Is the 1997 Harley Davidson Dyna Low Rider updated?

Is this the Low Rider of old, updated for the ninties? Absolutely not. In fact about the only thing Harley’s 1997 Dyna Low Rider has in common with the original FXS is a low seat height and the Narrow-Glide front end that, incidentally, has grown in fork size from a spindly 35mm to a more modern 39mm.

What was the first Harley Davidson Low Rider?

Dubbed the FXS, it was the first of Harley’s “factory customs” that would later include the Bad Boy, Road King, Fat Boy and the epic Heritage Springer. In addition to a low seat height, features on that first Low Rider included raised white lettered tires, drag bars, mag wheels, and an oft-copied two-into-one slash-cut exhaust.

Is the Dyna Low Rider the same as the FXS?

Absolutely not. In fact about the only thing Harley’s 1997 Dyna Low Rider has in common with the original FXS is a low seat height and the Narrow-Glide front end that, incidentally, has grown in fork size from a spindly 35mm to a more modern 39mm. What they do share is Willie G.’s flair for style and that wonderful potato exhaust note.

What happens when you discontinue power to the starter?

When you start the engine and release the key the circuit will, discontinue the power to the starting motor. If this stays on after the engine has started, the main contacts in the solenoid, have most likely failed. This will ultimately cause serious damage, to the whole starting system and the transmission flywheel.

What does it mean when Your starter won’t start?

When this occurs, it means the starter is not engaging with the flywheel. This is a worrying situation, which could result in having to replace the whole component. If you try to start your engine and the engine doesn’t start instantly, you may have to try again.

Do you know the signs of a failing starter motor?

Knowing the signs of a failing starter motor, can help you diagnose the problem. When Diagnosing starter motor problems, always start with the battery. So, for your starter motor to work properly, your car battery has to be in; excellent working condition and fully charged.

When you start the engine and release the key the circuit will, discontinue the power to the starting motor. If this stays on after the engine has started, the main contacts in the solenoid, have most likely failed. This will ultimately cause serious damage, to the whole starting system and the transmission flywheel.

Is there a problem with my Harley Davidson?

Click to expand… yea it was runing good before and it start fine as usual just when riding that it stall. i am going to take the battery off and get it checked and clean the end as u said thank you , hopefully thats the issue Yea hopefully it something simple. Check plugs and wires also.

What should I do if my Harley Davidson stall?

Also clean and check both ends of the cables to start with. Click to expand… yea it was runing good before and it start fine as usual just when riding that it stall. i am going to take the battery off and get it checked and clean the end as u said thank you , hopefully thats the issue Yea hopefully it something simple.

Is the Harley Davidson Dyna still on the market?

Harley-Davidson quietly killed off the famous Dyna product line for 2018 without so much as an official announcement, simply merging it’s Dyna products into the new Softail platform.

How to do a cruise control diagnostic on a Harley Davidson?

This modal can be closed by pressing the Escape key or activating the close button. If your Harley cruise control has an issue, there is an interactive cruise diagnostic test that can be performed on the motorcycle without the need or aid of any diagnostic service scan tools or computer.

What should I do if my Harley won’t start?

Everything works perfectly – Lights, hear the fuel pump kick on, signal, brakes, switches appear fine and I changed the gas to highest just in case and nothing. I checked spark by pulling a plug and starting while on the cyl. and no spark. Put a new coil in it and nothing. Cranks great and all is appearing to be fine but no fire/start?

I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.

I have a 2010 ultra classic with ABS. It is not starting. The battery voltage is 12.75 off the battery. When I turn the main switch on, I get a drop to 12.5, and when the kill switch is turned on, I get a drop to 12.38. The self test goes out and hit the start switch with nothing – no volt drop, no starter engage, no nothing. DEAD.

Is there a recall on the Dyna Low Rider?

Harley-Davidson Issues Recall of Dyna Low RiderHarley-Davidson has issued a recall of more than 8,000 Dyna Low Rider (FXDL 103) models because of an… Harley-Davidson has issued a recall of more than 8,000 Dyna Low Rider (FXDL 103) models because of an issue with the electrical system.

When did the Harley Davidson Dyna Low Rider come out?

The National Highway Traffic Administration reports that the issue has been the subject of more than 70 warranty claims, but so far there have been no reported crashes associated with the fault. Some 8,060 units are affected, covering models manufactured between 6 January 2014 and 7 April 2016.

What makes a Harley Dyna hard to start?

1. Spark plugs in bad condition or have improper gap or are partially fouled. 2. Spark plug cables in bad condition. 3. Battery nearly discharged. 4. Loose wire connection at one of the battery terminals, coil or ECM connector. 5. Water or dirt in fuel system. 6. Intake air leak. 7. Fuel tank vent hose and vapor valve plugged. 8.

Are there any recalls on Harley Davidson Low Riders?

Some 8,060 units are affected, covering models manufactured between 6 January 2014 and 7 April 2016. The NHTSA says riders she be alert to the possibility of slight hesitation when accelerating through the 4500 – 5500 RPM range. This may serve as a sign that the rider’s vehicle is affected.

How do you change the battery on a Dyna Glide?

Remove the outer battery cover fastener (1) and pull the battery cover (2) away from the battery tray (3). Disconnect both battery cables, beginning with the negative (black) terminal. Undo the battery strap (6) and remove the battery from the battery tray. With the battery removed, undo the battery tray fastening screws.

Why does my car not start when I try to start it?

But if the battery doesn’t have enough juice to start the engine or repeatedly needs a jump start, the problem may originate elsewhere, and jumper cables or even a new battery won’t solve the problem. Here are eight possible reasons your car won’t start.

How does the turn signal work on a Dyna Glide?

This article applies to the Harley Davidson Dyna Glide. There are many modules on your Harley Davidson that track as well as monitor the state of your powertrain and accessories. The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate.

What kind of engine does a Harley Dyna have?

But the “performance” Big-Twin-powered Dyna, with its signature rubber-mounted engine and twin rear shocks, had a huge following among Harley riders both young and old, so we are commemorating the popular model in this Motorcycle History piece.

Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.

What happens if you hit the starter button and nothing happens?

Battery good, lights , horn turn signal works. Fuel pump runs , hit starter and nothing, lights do not dim and no sound at all. All fuses O.K. starter relay maybe ? any advice ? 06 roadking by the way.

Battery good, lights , horn turn signal works. Fuel pump runs , hit starter and nothing, lights do not dim and no sound at all. All fuses O.K. starter relay maybe ? any advice ? 06 roadking by the way.

With a nimble frame, Twin Cam 96™ engine and smooth-shifting 6-Speed Cruise Drive® gearbox, the Dyna® Super Glide® Custom is just plain fun to ride. Up to two times thicker than the competition, custom quality paint comes standard on all Harley-Davidson® motorcycles.

How old is the 2012 Harley Davidson Super Glide?

2012 Harley-Davidson Super Glide Custom is a member of the Dyna family of Harley motorcycles. The SGC carries the Super Glide moniker, a model name that’s now 41 years old. As part of the Dyna line, the SGC enjoys other modern subtleties like the latest generation Harley switchgear, now with a new,…

What kind of bike is the Dyna Super Glide?

SICKK CUSTOM PAINTED FXDI Dyna Super Glide, MOTO T-BAR, SADDLEMEN 2-UP SEAT 2005 HARLEY DYNA SUPER GLIDE FXDI – Super clean old school/ new school bik… 2005 Harley-Davidson® FXD – Dyna® Super Glide®, 2005 Harley-Davidson® Dyna® Super Glide®

What kind of power does a 2005 Harley Davidson have?

SHARP 2005 SUPER GLIDE WITH FORWARD CONTROLS AND STAGE 1 LOW MILES!!! CALL 5152654444 AN… 2005 Harley-Davidson Dyna Super Glide, O- Stage 1 kit O- Vance and HInes exhaust Air cooled, 1449cc, 45° V-twin, OHV Power: 67.44 HP (49.6 2005 Harley-Davidson Dyna Super Glide Custom, 2005 Harley-Davidson® Dyna® Super Glide®

Why is my Harley Davidson Road King not starting?

If you have a Tachometer, disconnect it. A bad tach can interrupt proper coil function. i have problem error code U1301 in Harley Davidson Road King 2009 and test everything not starts . I have a 92 FXRSP, I recently replaced my switches and I had a new battery.

If you have a Tachometer, disconnect it. A bad tach can interrupt proper coil function. i have problem error code U1301 in Harley Davidson Road King 2009 and test everything not starts . I have a 92 FXRSP, I recently replaced my switches and I had a new battery.

What to do if your Dyna Glide is not working?

Check the shift arm and the shift rod from the shifter to the transmission to make sure all components are nice and tight. If your problem is with a Wide Glide, the problem could be the primary alignment. The 2006 and earlier models had an issue with the primary case causing an alignment issue.

Are there transmission issues on a Harley Davidson Dyna Glide?

Transmission issues with your Dyna can be a bit tricky to figure out. Some perceived problems are not actually problems at all, but just characteristics of the bike. Other things might be telltale signs that something is going on that needs to be addressed as soon as possible.

Why does my Dyna Glide make a whine when I Clutch?

If your clutch or gear noise is more of a whine, it may be indicative of a problem. A whine in 1st or 2nd gear when the clutch is released may indicate an internal issue. You may have an internal issue with the transmission.

No spark. Good fuel. The service dept. told me that the coil hardly goes bad. It might be the crankshaft sensor. I replaced it and it started.

What should the spark plug be on a Dyna?

Just disconnect it from the regulator and test the CPK side of the connector. I checked for a Dyna the primary coil side should only be between 0.3 and 0.5 ohms. I remembered 3 ohms from somewhere, maybe it was my truck. Anyhow if your coil is a sealed unit you will have to test the plug going in it.

Can a Dyna Super Glide crank but not start?

Discussion in ‘ Electrical ‘ started by 92chrisdyna, Aug 16, 2010 . 92 dyna super glide my bike cranks but wont start I have power to the coil and no spark I replaced the coil and nothing where do I go from here I am new to harleys and new to the forum and love some help from you guys thanks

No spark. Good fuel. The service dept. told me that the coil hardly goes bad. It might be the crankshaft sensor. I replaced it and it started.

Why is there no spark to my spark plugs?

There was no spark to the plugs. Was turning over real good. No spark. Good fuel. The service dept. told me that the coil hardly goes bad. It might be the crankshaft sensor. I replaced it and it started. Then a couple of days later it did the same thing, so spark.

Where can I find the 1997 Harley Davidson Dyna Wide Glide?

Also check out our overview of motorcycle webshops at Bikez.info. Join the 97 Harley-Davidson Dyna Wide Glide discussion group or the general Harley-Davidson discussion group. List related bikes for comparison of specs.

Also check out our overview of motorcycle webshops at Bikez.info. Join the 97 Harley-Davidson Dyna Wide Glide discussion group or the general Harley-Davidson discussion group. List related bikes for comparison of specs.

What kind of bike was the 1997 Dyna?

1997 Harley-Davidson® FXDWG – Dyna® Wide Glide®, GOING TO GO QUICK DON’T SEE A LOT OF THESE!!! BEAUTIFUL SHAPE 1997 DYNA WIDE GLIDE IN PLATINUM SIL… Cream Puff !! Cream Puff !! Probably one of the nicest Wide Glides of this era out there.

What kind of engine does the Harley Dyna Wide Glide have?

The Dyna Wide Glide FXDWG is full of classic chopper motorcycle style. New for 2012, the Harley Dyna Wide Glide features a new larger air-cooled Twin Cam 103 Harley engine with 6-speed cruise drive transmission, providing more power for passing, hill-climbing, and riding with passenger and cargo.

What are the problems with a Harley Davidson starter?

Harley Davidson Common Starter Problems Summary and Fixes – YouTube There are a few very common HD Starter problems. It starts with pushing the start button on only hearing a There are a few very common HD Starter problems. It starts with pushing the start button on only hearing a Skip navigation Sign in Search Loading…

What causes a car starter to not turn over?

The most common problem with a starting motor is, when you turn your key and nothing happens. A solenoid or motor that has burned out or electrical issues, may cause this as well. Furthermore, a dead battery can cause the same problem. It may appear that you have power to your starting system, but the engine will not turn over.

When do I need to replace my starter motor?

So, if this happens the starting motor will have to be replaced. The most common problem with a starting motor is, when you turn your key and nothing happens. A solenoid or motor that has burned out or electrical issues, may cause this as well. Furthermore, a dead battery can cause the same problem.

Why is my starter not working on my Harley?

That black wire with the red tracer should be sending 12v to the starter relay. Be sure that this wire is not damaged or pinched anywhere in its travel. This will be more common when wires have been routed through the bars, or switch housings/switches have been changed. Don’t forget to use your multimeter inside the switch housings too.

I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.

What causes a Harley Davidson to lose all power?

This can be caused by a loose neck or loose spokes (models w/spoke rims). Check your neck and tighten if nessacary. Also, can be caused by a bad wheel bearing. My first thought would be to load test the battery. 10v is low and if it he only gets a clicking when trying to start, that’s one sign of a bad battery.

How long does it take to change oil on a Dyna Super Glide?

Performed regularly, these oil changes can extend the life of your 2005 Harley-Davidson Dyna Super Glide dramatically, reducing wear caused by degraded oil. Changing the oil yourself is a simple task that normally takes less than an hour to accomplish using standard mechanics’ hand tools.

What are the codes on a Harley Davidson Dyna Glide?

Each code uses a letter in front of the number set that determines where the problem is stemming from. P are codes that relate to the ECM. C are codes that indicate issues with the ABS. B are codes that relate to the radio and accessories. U are codes that show problems with the modules.

1993: The Dyna Low Rider and Dyna Wide Glide are introduced, the two among the most popular Dyna models throughout the frame’s 26 year production run. 1995: Until this year, all Dynas had a 32-degree front rake, but in 1995 a more responsive 28-degree rake was introduced to the sportier Dyna models.

Which is the 2005 Harley Davidson Dyna Super Glide?

Join the 05 Harley-Davidson FXDCI Dyna Super Glide Custom discussion group or the general Harley-Davidson discussion group. List related bikes for comparison of specs. Get a list of related motorbikes before you buy this Harley-Davidson.

Performed regularly, these oil changes can extend the life of your 2005 Harley-Davidson Dyna Super Glide dramatically, reducing wear caused by degraded oil. Changing the oil yourself is a simple task that normally takes less than an hour to accomplish using standard mechanics’ hand tools.

How to replace the battery on a Harley Davidson Dyna Glide?

Harley Davidson Dyna Glide: How to Replace Battery. 1 Step 1 – Loosen the battery cover/support. Loosen the battery cover/support and slide it outboard. The battery cover/support looks like a rectangular 2 Step 2 – Disconnect the old battery. 3 Step 3 – Install and connect the new battery. 4 Step 4 – Tighten the battery cover/support.