Why is my AT Oil Temp light flashing?

If you see the “AT OIL TEMP” light come on in the dash, that’s telling you your automatic transmission fluid temperature is too hot. If the “AT OIL TEMP” light begins to flash immediately after starting the vehicle, it could indicate problems with the transmission control module.

Can I drive with at oil temp light flashing?

The first thing you should do when your light turns on and starts flashing is pull over and turn off your car. This could allow the oil to cool and give your car a much-needed break. Continuing to drive when the oil gets too hot, you’re running the risk of damaging other parts of your car.

Is AT oil Temp bad?

Running the car engine when the at oil temp light is flashing can lead to transmission failure causing the vehicle more damage. And overheating is one of the things can cause the most damage to your car transmission so quickly.

Is AT oil temp bad?

What makes the ABS come on at the temp light?

It happened again today, all the lights came on; ABS, Traction, AT temp light, CEL and airbag light. Car runs fine, no problems. Sometimes I can turn it off…no lights and then all the light show up again or only the ABS and Traction Light. So very strange.

What to do when your abs warning light goes off?

Once you have determined you are going to fix the problem, park the car on level ground with the transmission in park and the emergency brake set with the engine turned off. You may need to jack the car up to remove a tire or replace a control module. Always stay safe by using jack stands when lifting a car for repairs.

Why does the oil temp light come on in a Subaru?

Also because of the wiring in subaru, sometimes if the light bulb burns out, same lights will come on, replaced it. ( If you ask me, very dumb design) Car drives just fine, transmission is shifting great in any mode, no lag or hesitation.

Why are ABS, VDC and hill assist lights on?

Hill Assist, ABS and VDC light are on and flashing AT oil Temp. I thought maybe the battery is done, it hasn’t been changed yet and has died before from leaving flashers on for 30 min. Replaced the battery. From what i have researched so far:

Why is my AT oil Temp light flashing?

How do you fix a flashing oil temperature light?

If the AT Oil Temp light flashes while driving, please stop the car as quickly as possible in a safe place and allow the engine to cool or idle until the light goes off. If you keep driving the car in such condition for long you could cause more expensive transmission damage to your car.

What does the AT temp light mean?

A/T Oil Temp: This light is an indicator that the automatic transmission fluid temperature has increased and is too high. You should stop your vehicle immediately and put the vehicle in park until the light turns off. If the light does not disappear, have your vehicle inspected as soon as possible.

How do you check the transmission fluid in a Subaru Outback?

Automatic Transmission Fluid Park on a level surface and set the parking brake. Shift the selector level in each position. Then shift it in the “P” position, and run the engine at idling speed. Pull out the dipstick and check the fluid level on the gauge.

How do you cool down transmission fast?

Allowing the car to idle in neutral, while sitting at red lights, in congested traffic or at rail road tracks, reduces the strain on the transmission, allowing the transmission to cool.

How do you know if your transmission is overheating?

This article takes a closer look at three common signs of transmission overheating.

Acrid Burning Odor. Transmissions change gears using principles of hydraulic power.
Slow Response Times. A transmission stands a much greater chance of overheating if fluid levels drop too low.
Transmission Slipping.

How do you fix a high transmission temperature?

What to do when your transmission is overheating:

Stop driving immediately and let your transmission cool down.
Make a note of what you were doing, where you are, what’s happening (noises, etc.)
After cooling down, start back up & gingerly continue on your way.

How do you check the transmission fluid on a 2012 Subaru Outback?

Remove the dipstick, being careful not to spill or drip any fluid. Wipe off the dipstick with a clean rag, just as you would do when checking the engine oil. Reinsert the dipstick, then remove the dipstick again to check the fluid level. If you need to top it off, be sure to use the recommended transmission fluid.

What causes transmission to run hot?

Low fluid levels or old transmission fluid causes friction between the parts and causes overheating. Fluid problems are the most common reason for transmissions overheating.

What temperature is too hot for a transmission?

#1 Cause of Failure The optimal temperature range for transmission fluid is 175 to 220 degrees. Above that, for every 20 degrees bad things happen, starting with formation of varnish at 240 degrees, followed by seals hardening, plates slipping, seals and clutches burn out, carbon is formed, and, ultimately, failure.

Navigation