Why are the tail lights on my Jeep not working?

The socket can be removed asa separate piece, and it is fairly likely melted and/or burned If the tail lights were hot during the swap you may have broken the filiments. Bumping a bulb that is on or been on recently can cause the filiments to fail. Remove the bulbs hold them up to a light and see if the filimant is intact.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

What should I do if my tail light is not working?

Check the taillight bulbs. If the fuse and wiring look right, the bulbs themselves might be the problem. To check them, unscrew the taillight lenses from the outside using a screwdriver. If your lenses don’t have screws, open the trunk so you can access the lights from the inside.

Why are my brake lights burning out on my Jeep?

The fuse chart is cryptic at best, this weekend I may eventually resort to scrutinizing every fuse in the jeep. Its fairly common for these to burn out sockets for the bulbs, and even often on both sides at the same time. The socket can be removed asa separate piece, and it is fairly likely melted and/or burned

Why are there no tail lights on my Jeep Grand Cherokee?

My 2004 grand cherokee is acting all sorts of crazy im really convinced that its always had some sort of electrical issue somewhere that hasnt been found yet. The current issue im battling is a brake light. tail lights work but not brake one side or the other intermittently.

Is it dangerous to have a broken tail light?

As we all know, tail lights are quite important and crucial on any vehicle. So, driving with broken tail lights is very dangerous. Actually, people find out about their tail light problem when the police officer pulls them over. This is because the tail light malfunction is not that easy to spot.

@chuyin ,Jesus Contreras , If after checking all fuses and bulb’s and does not rectify the issue, check the bulb sockets them selves for corrosion, burnt, contacts may need pried up a bit (little) to enable grounding or power to the bulb, (this is a common issue) if contacts broke or badly burnt, replace the socket.

Are there any problems with my 2004 Jeep Grand Cherokee?

I have a problem on my 2004 Jeep Grand Cherokee. the tail and license plate lights do not work, but the brake , directional back-up, and the hazard lights are working normally THANKS! Answered! View the answer I have this problem too

What to do if your tail light is not working?

Now, if you are certain that your tail light is not working, and the light bulb is just fine, it is recommendable to take your car to mechanics. Simply speaking, every time there is an electrical problem with the car, it is highly recommendable to let the professionals handle it.

Why is my brake light not working on my Jeep Grand Cherokee?

Jeep Grand Cherokee brake light not working – fixed! – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

What to do if your tail light doesn’t work?

An expert who has achieved level 1. An expert whose answer got voted for 2 times. If you take the tail light assembly off and take the bulb out, you’ll see three metal contacts on the tail light assembly. Pry them up slightly and slide a small, folded piece of aluminum foil underneath it. Replace the bulb and try to reproduce the problem.

If it is the tail lights that are inop there are some common problems associated with this model Jeep. The most common is the tail light sockets. They often melt the housing they fit into and consequently lose ground. The only way to properly fix this is by replacing the entire taillight assembly” italic text”.

What to do if your brake lights stay on?

If the bulbs are OK, the brake light switch and the rest of the circuit will have to be traced. If you want these steps performed by a certified Mechanic, dispatched by YourMechanic right to your location, please request an electrical circuit diagnostic and the responding certified mechanic will get this problem resolved for you.

What kind of Lights does a Jeep Grand Cherokee have?

All the lights (Check engine, transmission, abs, auto traction, etc, etc, etc) in my 2006 Jeep Grand Cherokee 4.7 Laredo’s instrument panel suddenly went on and off twice while driving (First time ever)…. And then the auto traction light as well as the ESP/BAS lights stayed on…

Why are all the lights flickering in my Jeep?

Long story short, the battery was going bad. It was causing some REALLY weird things to happen: dash lights flickering, seat heaters wouldn’t work for 2 to 3 minutes after a start, then the things I described above started happening. Changed the battery 6 months ago, everything disappeared!!!

Why do my brake lights stay on when the car is off?

I would look for a switch hanging. If the problem is brake lights check the brake light switch usually by the brake pedal. If not get a repair manual from Auto Zone or someplace like that with a good electrical diagram in it and trace put the circuit that’s staying on.

Why are the reverse lights on my car not working?

If you replace the bulbs in your vehicle and the lights are still not working, chances are a sensor has gone bad. If this happens, take it to YourMechanic, as you are required to have working reverse lights on your vehicle as it is a safety feature. Another reason your lights could have gone out is from the reverse light switch.

Why does my reversing light only light on one terminal?

If the lamp lights on both terminals, the fault is in the wiring between the switch and reversing lights. If the lamp fails to light at all, check the wiring between the fuse and switch. If the lamp only lights on one terminal, the switch is either broken or needs adjusting.

When do you need to replace your reverse light switch?

If your reverse lights are always on, never on, or function intermittently, you may have to replace the car’s backup light switch. 1. Reverse lights function intermittently

Can a bad light switch cause a car to go in reverse?

If the switch shorts internally, this may cause the lights to stay on permanently. This will not only be a problem in that it will make the vehicle appear that it is in reverse gear when it is not, but it will also cause the bulbs to burn out much more rapidly than they normally would. 3. Reverse lights fail to come on at all

What are the symptoms of a bad backup light switch?

1. Reverse lights function intermittently 2. Reverse lights stay on at all times 3. Reverse lights fail to come on at all Average rating from 130,525 customers who received a Vehicle Body Electrical and Lighting Inspection. The backup light switch is the electronic switch on a vehicle that is responsible for activating the vehicle’s reverse lights.

Why does my light switch keep coming on and off?

If the contacts in the switch are worn or have failed, then this may cause the lights to function intermittently. You may notice that the reverse lights will come on sometimes and not others, or that they may flicker on and off rapidly or randomly.

When do reverse parking sensors begin to malfunction?

Reverse parking sensors may begin to malfunction over time, or if you have been in an accident, and when a driver isn’t aware of the problem, things can quickly get dangerous. If you notice anything off with your sensor, test it out immediately.

What are the fuses on a 1999 Jeep Grand Cherokee?

Fuse box diagram Jeep Grand Cherokee 1999-2004 Cavity Fuse Description 19 10 Amp Red Antilock Brakes 20 10 Amp Red Ignition Run 21 10 Amp Red Ignition Run/Start – PDC 22 10 Amp Red Ignition Run/Start

What are the running lights on a jeep TJ?

For this vehicle (2000 TJ), running lights (ie: when the headlights are on) are Black. Turn signal, brake and flashers are Green on the left and Brown on the Right. Back up is Purple.

When to replace the tail light assembly on a Jeep Grand Cherokee?

Therefore, if you need tail light assembly replacement for Jeep Grand Cherokee, turn to AutoZone. The tail light assembly covers the turn signals and rear lights on your SUV. If your Grand Cherokee tail lamp assembly is cracked, it’s time to restore the look of your vehicle by replacing it.

How much is the tail light assembly at AutoZone?

Shop AutoZone for Jeep Grand Cherokee Tail Light Assembly. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only One of the greatest features of your Jeep Grand Cherokee is versatility.

When do the tail lights and brake lights come on?

The taillights come on when your headlights are on or your parking brake is engaged. The brake lights turn on when you apply pressure on the brakes. In most automobiles, the taillights are red while the brake lights are a brighter, more luminous red. The rear lights are controlled by the same switch as the headlights.

Where is the fuse panel on a Jeep Grand Cherokee?

The fuse panel is located by the drivers left knee under the dash. https://w05.dealerconnect.chrysler.com/s… Was this answer helpful?

When did the Jeep Grand Cherokee get redesigned?

The Jeep Grand Cherokee was redesigned for the 1999 model year; the 2000 models have minimal changes. This model is also known as Jeep WJ. Hi! I have a problem on my 2004 Jeep Grand Cherokee.

Why are the head and tail lights not working?

The on-board computer turns on the tail and headlights according to the light outside the car. If it is dawn or dusk the head and tail lights will come on by themselves. The light sensors also switch off the daytime lights in some latest models. When the sensor is dirty or damaged it cannot tell if it is dark or day outside.

Is it dangerous to drive with broken tail lights?

So, driving with broken tail lights is very dangerous. Actually, people find out about their tail light problem when the police officer pulls them over. This is because the tail light malfunction is not that easy to spot. Usually, brake lights are the problem and the tail lights work just fine. But, sometimes it’s the opposite.

If the taillight problem you are having is on your Jeep Wrangler, I recommend checking for a blown taillight fuse in your fuse box cavity M17. This is a 15 amp blue mini fuse for the Left Tail/License/Park Lamp. If the fuse is fine, check the blub to make sure the taillight filament is not burned out.

How can I tell if my tail lights have a fuse?

When you have located the fuse for the tail lights use a fuse tester to check the connection. If the tester lights up – your fuse is functioning fine. If it does not light up then, replace the fuse with another of the similar amperage and size. In many instances, you can see the break in the metal strip of the fuse.

Why is the tail light on my car not working?

The Tail light on the drivers side is not working, but the passenger side is working. The brake lights are on the same bulb, and both work. I changed the bulb, and still the same problem.

Is the left tail light and parking light the same?

(Same Bulbs (2) as the parking Light) left TAIL light, left PARKING light does not turn on when i turn the headlights on with the standard 2 position pull knob on the dash. It only effects the left side of the car. Right side works properly. Check 10 amp fuse in location 7 of fusebox, this is for park lamps on left side.

The fuse panel is located by the drivers left knee under the dash. https://w05.dealerconnect.chrysler.com/s… Was this answer helpful?

Why does my left brake light not work?

When the headlights are not on – all brake lights function properly.. as soon as I turn on the headlights the Left brake light does not work. Have taken it to a jeep dealer and another shop and one told me they could find nothing wrong — the dealership told me they fixed it but they didn’t.

How long does it take to take off a jeep license plate light?

Took about 20 mins once I figured out what I had to do. Popped inside panel off, unscrewed about 12 nuts from the inside. Took off both rear lights from hatch and also had to remove the outside panel that has Jeep emblem on it. Everything went right back into place and all is good.

The Jeep Grand Cherokee was redesigned for the 1999 model year; the 2000 models have minimal changes. This model is also known as Jeep WJ. Hi! I have a problem on my 2004 Jeep Grand Cherokee.

Is the 2014 GC license plate light led?

In 2014 (lucky me) they went to an LED instead of a bulb. The dealer wants $130 for the LED part which is insane. I have searched pretty extensively but can’t find a replacement anywhere.

Why are there no parking lights on my 92 Cherokee?

92 cherokee limited No Parking Lamps,Dash,lights! Well this started after the battery went dead. First the head lamp flashed after installing new battery. reset security with key lock and unlock drivers and passenger door. Head lamps stopped flashing after locking and unlocking passenger door.

Why do my tail lights keep coming on?

The most common is the tail light sockets. They often melt the housing they fit into and consequently lose ground. The only way to properly fix this is by replacing the entire taillight assembly” italic text”.

How can I get my rear lights to turn off?

Very easy to install.. push down the brake pedal and you will the hole.. take the stopper and pop into the hole until it pops.. and do the same for the cruise control switch. And then you are all done.. Then no more problems with lights not turning off. Thank you! I pressed the brake circuitry plug all the way in and they turned off.

What happens when the tail light goes out?

When the filament inside the bulb breaks it cannot illuminate the gas enclosed within the glass cover. This burnt-out bulb does not affect the circuitry of the light system and it continues to function normally. You may have to remove the cover of the tail light.

Why are my tail lights not working but brake lights are working?

Burnt out light bulbs – The other reason your tail lights are not working but your headlights are maybe a blown bulb. When the filament inside the bulb breaks it cannot illuminate the gas enclosed within the glass cover. This burnt-out bulb does not affect the circuitry of the light system and it continues to function normally.

What to do if your light switch wont work?

If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb. Or, the entire switch may be faulty, in which case, have it replaced by a certified mechanic. Turn off your headlights and vehicle when you’re done.

Why are the lights on my dash not working?

Flip the switch or turn the dial or knob up and see if the lights on your dash come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb. Or, the entire switch may be faulty, in which case, have it replaced by a certified mechanic.

What causes death wobble on a Jeep Wrangler?

Worn wheel bearings may contribute to death wobble as well and are very easy to test. Jack up one of your Jeep’s front wheels and grasp the tire at the 12- and 6-o’clock position, then wiggle the tire. If you feel movement, then you most likely have a worn wheel bearing. Check the other side as well.

What does it mean when there are no dash lights?

Found loose connection between headlight switch and fuse panel for tailights no tailights = no dash lights. Did you find the recommended reading relevant to this discussion? Help us improve your recommendations by telling us what you would like to see.

Why is my tie rod not moving on my Jeep?

Your Jeep’s tie rod and tie rod ends should be next on the hit list. To check these, use a jack to lift up the front of the Jeep and then have a friend grab one wheel and twist it back and forth. If the tie rod doesn’t move, but the ends seem to wiggle, then they most likely need replacement.

What does a fuse do on a Jeep Grand Cherokee?

Fuse box diagram (fuse layout), location, and assignment of fuses and relays Jeep Grand Cherokee (WJ) (1999, 2000, 2001, 2002, 2003, 2004, 2005). A fuse is an element for protecting the electrical system. A fuse will trip (i.e. it will blow) in the event of a failure or improper interventions in the electrical system.

Why do my rear lights stay on all time?

sounds to my like there is a bad connection from (-) to the chassis somewhere. In this case the (+) from somewhere else is using the (-) connection of your rear lites and that’s the reason why the stay on all time. If you know how to use a multimeter follow the wires backwards an see where the (+) comes from.

Why are my parking lights not working on my Jeep Wrangler?

Make a jumper wire & jump from 4 to 1 & check for short. Then jump 4 to 9 & check. If both are good you may have an internal short in the switch. The dome light part of the switch grounds that circuit to turn them on & if those contacts are connecting with the park light contacts then that could be causing the short.

Are there parking lights and no tail lights?

However the dash, tail and parking lights still do not come on. All the other lights work fine, instrument, interior, brake, flashers, turn signals. Just no tail lights, parking lights or dash lights. Fuses are fine as are the bulbs. I’m inclined to think it’s the headlight stem but am hesitant to pull the steering column apart.

What kind of tail lights do Jeep Cherokees use?

Jeep Cherokee 2000, Black/Red Euro Tail Lights by Anzo®, 1 Pair. Black housing, red/clear lens. The simplest way to make your vehicle look gorgeous and unique is to replace the stock lighting units with exclusive custom ones. To do the… Jeep Cherokee 2000, Black/Red Euro Tail Lights by CG®, 1 Pair. Black housing, red/clear lens.

For this vehicle (2000 TJ), running lights (ie: when the headlights are on) are Black. Turn signal, brake and flashers are Green on the left and Brown on the Right. Back up is Purple.

Why are the tail lights on my Jeep YJ not working?

If you have the stock tail lights remove the lense and fully inspect the wires and connections and light socket. I had the same problem on a Yj and the problem was corrosion in the tail light housing.

Why are my brake lights not working on my Jeep Grand Cherokee?

Electrical contacts in the tail lamp housing tend to break or melt, which can cause the brake lights to fail or work intermittently. Complete inspection of the tail light housing and bulbs is recommended before replacing any parts. The average cost for a Jeep Grand Cherokee General Diagnosis is between $88 -$111.

What are the features of a Jeep Grand Cherokee?

One of the greatest features of your Jeep Grand Cherokee is versatility. Whether transporting your family or towing your toys and passengers to a remote campsite, your Jeep Grand Cherokee does it all. Keeping your vehicle in supreme condition is important to you.

Why are the reverse lights on my Jeep not working?

I checked the bulbs and they are fine, the socket is good, so I chocked the wheels and put in in reverse and… nothing. No voltage at all from the harness for reverse. Turn signals, tail, and brake lights all work fine. Is there a fuse I should look for or a switch on the transmission that activates the reverse lights?

Where are the backup lights on a jeep?

The backup lights switch is part of the TRS/solenoid block inside the tranny. The backup lights switch is part of the TRS/solenoid block inside the tranny. Click to expand… I haven’t had any tranny codes lately but I guess it might be time to replace the solenoid block and do the transgo kit.

Why are there brake lights but no tail lights?

Brake lights, but no tail lights. If the tail lights were hot during the swap you may have broken the filiments. Bumping a bulb that is on or been on recently can cause the filiments to fail. Remove the bulbs hold them up to a light and see if the filimant is intact.

What are the new tail lights on a jeep?

On the new taillight, Black was the running light, White was the brake, turn and flasher and Red was the ground wire. Happy hunting! Keep us posted. :thumbsup:

Where are the running lights on a quadratec Jeep?

On the left, I used a ring connector and screwed the plate mounting screw to the connector. On the right, another ring connector was used with a small sheet metal screw through the backside of the wheel well. On the new taillight, Black was the running light, White was the brake, turn and flasher and Red was the ground wire.

How are the rear lights and brake lights connected?

The rear lights are controlled by the same switch as the headlights. The power flows through a relay to the rear lights when the switch is turned on. While the brake light switch is connected to the brake pedal which comes on when the pedal is pressed.

What does it mean when your brake lights are off?

These lights illuminate brighter when you are applying brakes. This indicates to the person behind you to stop or slow down and change their path. During the day the headlights are off and only the rear lights are used to indicate that the driver is applying brakes.

Why is the left side of the turn signal not working?

This time, though, the left or right side of the signals doesn’t work. You may see the dash indicator lamps illuminating brightly, but the turn lights won’t flash. You may be dealing with bad bulbs or a fault between that side of the circuit and the turn signal switch itself.

Why do emergency lights and turn signal lights not flash?

If the emergency lights and turn signal lights illuminate but don’t flash, check first for a burned-out bulb. This is the most common cause. If not, you may be dealing with a bad flasher unit or a bad turn signal switch. See the sections ‘Testing the Turn Signal Flasher’ and ‘Checking the Turn Signal Switch.’

Why is my blinker not working on my Turn signal?

A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action. Learn more – Locate turn signal flasher in Google Images. Step 4 – When a turn signal switch fails the system will short or go “open” causing the blinker not to operate.

Why do my tail lights stay on even after I Turn Off the car?

Thank Kevin. If the tail lights are illuminated even after you have used the on-off switch to command them off, that means the switch supplying power is fused shut and/or the circuit is being powered when it is not supposed to be due to a wiring fault.

Do you need a tail light assembly for a Jeep Grand Cherokee?

Keeping your vehicle in supreme condition is important to you. Therefore, if you need tail light assembly replacement for Jeep Grand Cherokee, turn to AutoZone. The tail light assembly covers the turn signals and rear lights on your SUV.

What to do if your tail light assembly is cracked?

Unfortunately, your rough-and-tumble adventures wreak havoc on your vehicle. If your Jeep Cherokee tail light assembly is cracked, AutoZone has a replacement assembly that restores the look of your Jeep. Tail light assembly replacement for Jeep Cherokee also increases your visibility.

Navigation