Where is the radiator drain plug on a Jeep Cherokee?
This should be done only before the Grand Cherokee has been started for the day. Open the hood to allow light down into the engine compartment. Put on your safety glasses and crawl under the Jeep on a creeper to locate the radiator drain plug.
When to replace the radiator on a Jeep Grand Cherokee?
Replace the antifreeze into the radiator when you’re done using the same antifreeze from the drain bucket or a 50-percent mixed antifreeze recommended for your year Jeep Grand Cherokee. You will need to start the engine and allow it to warm up with the radiator cap off.
When to drain coolant from Jeep Grand Cherokee?
Do not drain the coolant from your Jeep Grand Cherokee until the engine and coolant have cooled down. This is not something you should attempt to perform after taking a trip to the parts store to get more coolant to replace or any other errands.
Can you drain the radiator on a Jeep Grand Cherokee?
Draining the radiator on your Jeep Grand Cherokee is not overly difficult and by doing it yourself, you can save money. Draining and filling your radiator is a low-line maintenance procedure with the understanding that you’re not replacing all the coolant in your system.
Where is the drain plug on a Jeep Grand Cherokee?
Put on your safety glasses and crawl under the Jeep on a creeper to locate the radiator drain plug. On a 4.0 liter engine, it will be on the right (passenger side) side of the inside of the radiator and on a 4.7 liter engine, it will be on the left (driver’s side) side of the inside of the radiator.
How do you remove coolant from a Jeep Grand Cherokee?
To properly remove and replace coolant from any vehicle, follow these steps. Do not drain the coolant from your Jeep Grand Cherokee until the engine and coolant have cooled down. This is not something you should attempt to perform after taking a trip to the parts store to get more coolant to replace or any other errands.
How do you remove a condenser from a radiator?
Remove the Reservoir line and set aside.` Pull the radiator support (the metal bracket on top of the radiator) with a socket wrench, in this case it is 10mm nuts and bolts on all sides of the support. If you don’t need the A/C condenser, go ahead and unbolt it from the radiator now.
To properly remove and replace coolant from any vehicle, follow these steps. Do not drain the coolant from your Jeep Grand Cherokee until the engine and coolant have cooled down. This is not something you should attempt to perform after taking a trip to the parts store to get more coolant to replace or any other errands.
How to add coolant to a Jeep Liberty?
Be sure to check your owners manual to determine the correct type of fluid to add – for Jeeps, it will typically be in a section titled Fluid Capacities in the back of your manual. Mix the coolant with distilled water so that you have a combination of 50% coolant and 50% water.
This should be done only before the Grand Cherokee has been started for the day. Open the hood to allow light down into the engine compartment. Put on your safety glasses and crawl under the Jeep on a creeper to locate the radiator drain plug.
How do you replace a radiator drainage plug?
This is a short tutorial video on how to replace your radiator drainage plug. Mine snapped off because it is plastic so I had to figure out a way to replace it. Vehicle: Used a Ford Ranger but process can likely be used in many scenarios. Supplies needed: Needle nose pliers, bucket, replacement plug. Loading…
Replace the antifreeze into the radiator when you’re done using the same antifreeze from the drain bucket or a 50-percent mixed antifreeze recommended for your year Jeep Grand Cherokee. You will need to start the engine and allow it to warm up with the radiator cap off.
How does a jeep radiator and cooling system work?
5) Fan – This system can be either mechanical, electrical or a combination of both. The fan, depending on design, will push or pull cooler air through the radiator to aid heat-transfer from the coolant. 6) Fan Clutch – The fan clutch is used on mechanical fans only. It is designed to keep the optimum amount of air flowing through the radiator.