Where is code p2764 on Subaru CVT?
Subaru CVT chain, same concept as belt driven CVT transmissions. On to the repair for codes P2764 and P0700 codes. The test is to ohm check the lock up control solenoid, this is a two wire solenoid, the bulk head electrical connector and can be accessed from the top of the transmission.
What does the p2764 code in OBD-2 mean?
What the P2764 code means. The P2764 code is a standard OBD-II trouble code for the torque converter clutch pressure control solenoid circuit. The powertrain control module (PCM) uses the engine load and speed, as well as the vehicle speed and throttle position to select the needed torque converter clutch application (called “lock up”) degree.
What are the p2762 and p2764 torque converter codes?
Hi everyone. I have a 2011 Subaru outback and have been getting the codes P2762 and P2764 which seems to indicate that because I am getting both codes that the Torque Converter Clutch Pressure Control Solenoid Control Circuit is bad.
What’s the error code on my Subaru p2700?
Had that fixed by the Subaru dealer under the recall, but all my lights (Hill Assist, Slick resist, ABS, Check Engine and AT OIL TEMP) are still lit up less than a week later. After running a couple of diagnostic tests, I got the error code P2764 along with a P2700.
How to fix code p2764 on a Subaru?
Code P2764 lock-up duty solenoid circuit (low) This video shows the replacement of the valve body in this Subaru continuously variable transmission, and also…
What the P2764 code means. The P2764 code is a standard OBD-II trouble code for the torque converter clutch pressure control solenoid circuit. The powertrain control module (PCM) uses the engine load and speed, as well as the vehicle speed and throttle position to select the needed torque converter clutch application (called “lock up”) degree.
Hi everyone. I have a 2011 Subaru outback and have been getting the codes P2762 and P2764 which seems to indicate that because I am getting both codes that the Torque Converter Clutch Pressure Control Solenoid Control Circuit is bad.
What’s the CVT code on a Subaru Outback?
I got the 2763 code for a “high” solenoid and when I pulled it and tested it I got a 68.5 when it should be 12. New valve body tested at 12 and all other solenoids on both were normal. I’ve got the 2763 code and replaced the valve body. Am adding new CVT fluid to it tomorrow. Did you folks have to take car to dealer for a “relearn” on the CVT?
Subaru CVT chain, same concept as belt driven CVT transmissions. On to the repair for codes P2764 and P0700 codes. The test is to ohm check the lock up control solenoid, this is a two wire solenoid, the bulk head electrical connector and can be accessed from the top of the transmission.
How does a Subaru Legacy Drive with these codes?
Hi,codes P0966 is for the self shut relay,all fuses in the main box under the hood should be inspected,P0890 is for the forward and reverse solenoids in the transmission,how does the car drive with these codes yu should be having some issues The relearn will need to be done with a new transmission,I am really surprised dealer told you it wouldn’t
What is the p2764 code for the Check Engine light?
A part number or two from subaru so i can check for parts would be helpful as well. Thanks. I just got the same code today: P2764 along with the P0700 code for the check engine light. I was wondering what the outcome of your situation was?
What happens when a transmission fails on a Subaru?
The transmission goes into a failsafe mode with CEL P0700 transmission failure MIL requested. Using a Snap-On scanner we can access the transmission computer to get more specific codes. The transmission computer stores a P2764 Lock up duty solenoid circuit low.