Where can I find the OBD code on a Nissan Maxima?

Nissan Corporation OBD I diagnostic page explains how to get the codes without any special tools. The codes are listed seperately for Maxima and Sentra models as needed. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.

What is the trouble code for a 1996 Nissan?

Trouble Code Info Model Year Engine identification System 200SX 1.6L 1996-98 GA16DE Nissan EGGS 200SX 2.0L 1996-98 SR20DE Nissan ECCS 240SX 2.4L 1996-98 KA24DE Nissan ECCS 300ZX 3.0L 1996 VG30DE Nissan EGGS

What does a diagnostic code on a Nissan mean?

A diagnostic code is helpful when troubleshooting a particular problem that has occurred. After the trouble code is defined the problem can be repaired and rechecked. Early Nissan check engine lights are not used to blink out a trouble code like on most vehicles but instead use a mode and retrieval method.

Where do I find the trouble code on my Nissan?

On all models, to erase DTCs using generic scan tool (GST), select mode 4. Place diagnostic switch in the Off position. Place ignition switch in the On position. Crank engine. Start and operate engine. The trouble codes will be displayed by the flashing Engine Control Lamp and the Overheat Warning Lamp and the Overheat Warning Buzzer.

What are the OBD codes for Nissan Sentra?

The codes are listed seperately for Maxima and Sentra models as needed. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.

What is the OBD code for a Nissan check engine light?

Refer to our Generic OBD II code listfor definitions on all other Nissan diagnostic trouble codes. Manufacturer Specific Codes P1105MAP/BARO Pressure Switch Solenoid Valve P1110Intake Valve Timing Control Solenoid

How does a fault code work on a Cummins Engine?

Fault codes are Cummins way of letting you know that your engine has a problem. Every sensor and circuit on your engine has a certain expected reading and voltage signal. These signals are monitored constantly by the Cummins ECM.

How to clear engine OBDII Codes without Nissan consult?

ECM has entered to Diagnostic Test Mode II (Self-diagnostic results). How to clear the engine codes without a Nissan CONSULT or scan tool. Set ECM in Diagnostic Test Mode II (Self-diagnostic results). Fully depress the accelerator pedal and keep it for more than 10 seconds.

How to access the ECM on a Nissan?

Access the ECM. On the side there is either 1 LED or 2 LEDs. Also there is a screw. With the ignition switch in the “ON” position, gently turn the screw fully clockwise, wait 2 seconds, and then counter clockwise. This procedure takes the vehicle from Mode I (normal running) to Mode II or Mode III Diagnostic.

Where is my OBD2 port in Nissan?

The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate. To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Go the the Nissan. OBD2 car scanner.

Which is better Nissan scan tool or OBD station?

A Nissan scan tool has advantages over more general diagnostic scanners designed for wide vehicle compatibility. You’ll save some money, first of all, since those tools are often made (and priced) for professionals. In addition, Nissan scan tools support the OBD2 protocols used in the manufacturer’s vehicles.

How long does it take for a Nissan OBD code to appear?

For example, a code 12 will be displayed by the check engine lamp flashing 1 time for approximately 1.2 seconds, followed by a .6 second pause, then 2 short flashes. Each trouble code will be displayed 3 times before the next trouble code is displayed.

Where is the diagnostic port on a Nissan Maxima?

A Nissan Maxima’s second-generation On-Board Diagnostic Connector can be found under the dashboard and to the left of the steering column. It will be uncovered, with no access panels blocking it from view. OBD-II For all Nissans manufactured after 1996, the OBD-II access port is called a Data Link Connector.

Where is the computer located on a Nissan Maxima?

Nissan vehicles predating 1996 use a special computer system. The Maxima’s central computer module is located inside the vehicle, on the passenger’s side. The diagnostic system relays fault codes through a special box outfitted with an LED light. Codes come in two-digit numbers, and the codes are conveyed with long and short LED flashes.

Where is the diagnostic system located on a maxima?

The Maxima’s central computer module is located inside the vehicle, on the passenger’s side. The diagnostic system relays fault codes through a special box outfitted with an LED light. Codes come in two-digit numbers, and the codes are conveyed with long and short LED flashes.

How to clear engine codes without a Nissan consult or scan tool?

How to clear the engine codes without a Nissan CONSULT or scan tool. Set ECM in Diagnostic Test Mode II (Self-diagnostic results). Fully depress the accelerator pedal and keep it for more than 10 seconds. The emission-related diagnostic information has been erased from the backup memory in the ECM.

What is the diagnostic code for a Nissan check engine light?

Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s). Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code listfor definitions on all other Nissan diagnostic trouble codes. Manufacturer Specific Codes P1105MAP/BARO Pressure Switch Solenoid Valve

When did the Nissan Maxima get its name?

The size of Maxima varied from generation to generation; compact class between 1977 and 1988, mid-size class between 1988 and 20 0 3 and the full-size from 2003.The “Maxima” name was applied gradually, beginning in 1981.

Are there any manuals for the Nissan Maxima?

Every Manual available online – found by our community and shared for FREE. Enjoy! The Nissan Maxima is an entry level luxury car from Japanese automaker Nissan since 1981. Marketed by Nissan as a ?four-door sports car?, it was originally an upscale version of Nissan Bluebird, known as Datsun 810 .

How to find the Nissan OBD diagnostic trouble code?

Trouble codes are indicated by number of flashes from ECM Red LED and Green LED inspection lights. Count number of flashes. Red LED indicates first digit of code, and Green LED indicates second digit of code. For example, 3 flashes of Red LED followed by 2 flashes of Green LED indicate Code 32.

When did the Nissan Maxima stop being called a Datsun?

In 1981 for the 1982 model year, all 810s were rebranded as Datsun Maxima. In 1983 for model year 1984, the last year of the first generation Maxima, North American Datsuns began carrying the “Nissan” badge as well.

What kind of automatic does the Nissan Maxima have?

For the first model year, the 810 Deluxe was the only version to receive the five-speed manual, while the luxurious 810 Maxima only came with a three-speed automatic.

What are the new colors for the Nissan Maxima?

For 2012, Nissan modestly freshened the Maxima’s exterior, with a new grille, taillights and new alloy wheels in 18- and 19-inch diameters. Three new exterior colors, Java Metallic, Dark Slate, and Pearl White are available.

What kind of sound system does a Nissan Maxima have?

The North American 1995 Maxima included a Bose Sound System on the GLE (optional on the SE) which had a 6 speaker sound system, a Clarion system was also an option (non-Bose). The fourth generation Maxima was highly praised for its quiet, roomy interior.

When do I change the trouble code on my Infiniti?

A change from one digit numeral to another occurs at an interval of 1.0-second OFF. In other words, the later numeral appears on the display 1.3 seconds after the former numeral has disappeared. A change from one trouble code to another occurs at an interval of 1.8-second OFF.

How to get Nissan codes obd1-2carpros?

Step by step guide on how to retrieve troubles codes from Nissan vehicles 1995 and earlier, including code chart. Begin with the vehicle on level ground, engine off with the emergency brake set. Step 1 – To boot the computer in mode four make sure the key is in the “OFF” position.

The codes are listed seperately for Maxima and Sentra models as needed. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.

How to read NISSAN OBD 1 codes without OBD scanner?

How To Read (Retrieve) Nissan OBD 1 Codes without OBD Scanner. Easy way to read, accessing, erasing and resetting obd1 codes on nissan cars. Trouble codes are displayed by the malfunction indicator lamp (MIL). The ECM fault memory can also be checked using diagnostic equipment connected to the data link connector (DLC).

Where to find Nissan check engine light codes?

These are listed in numerical order for easy searching. When retrieving Nissan check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.

How to know if Nissan P0300 is the only code?

Use FIXD to scan your Nissan to verify P0300 is the only code present. If other codes are present, they must be addressed first. Check for loose connectors at the ignition coils or for damaged wiring. Look for loose engine ground wires as well.

How to find the Nissan OBDII trouble code?

A particular trouble code can be identified by the number of four-digit numeral flashes. The ‘zero’ is indicated by the number of ten flashes. The length of time the 1,000th-digit numeral flashes on and off is 1.2 seconds consisting of an ON (0.6-second) – OFF (0.6-second) cycle.

What to do if your Nissan OBD is not working?

With ignition switch in ON position and engine not running, insert screwdriver through access port on ECM. Turn screwdriver fully clockwise. Wait at least 2 seconds. Turn screwdriver fully counterclockwise. Inspection light will begin to flash. This is Mode II. Turn ignition switch to ON position.

What happens when your car is not ready for an OBD test?

The status of the emission systems may also be reset by disconnecting the battery. After being reset, the emission systems on your vehicle will have a “not ready” status.

How do you find the fault code on a Nissan?

Turn the ‘diagnostic mode selector’ screw on the computer fully clockwise. The check engine light will go off. Wait 5 seconds, then turn the screw fully counter clockwise. 3. The check engine light will then begin to flash stored fault codes. The long flash (s) = 1st digit; short flashes = 2nd digit. 4.

Is the service engine soon light on a Nissan Maxima?

Nissan only uses one light — the service engine soon light — to take care of these functions. The only way to keep the light off is to repair the problem that turned the light on before attempting to turn it off. Turn the ignition switch to the on position but do not start the car.

How does the trouble code work on a Nissan Leaf?

How much does it cost to diagnose Nissan p0150 code?

The cost of diagnosing the P0150 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0150 NISSAN code detected?

How much does it cost to repair Nissan p0745?

The cost of diagnosing the P0745 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

How much does it cost to diagnose a Nissan code?

The cost to diagnose the P0745 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?

How long does it take to diagnose a Nissan transmission fault?

Excessive debris or metal particles on the transmission pan could be an indication that there is a mechanical transmission failure and that the transmission will need to be rebuilt or replaced. The cost of diagnosing the P0745 NISSAN code is 1.0 hour of labor.

The cost of diagnosing the P0745 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does the p0725 Nissan ECM code mean?

P0725 NISSAN Meaning The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send a signal to the Transmission Control Module (TCM).

How to contact Nissan Maxima error code repair?

The benefits of this repair service are: Over 9,000 5 star customer reviews and growing! Note: If you do not have a P0505 error, or are having problems other than these, do NOT send your unit without contacting us first at 800-547-2049. Wondering How This Repair Service Works?

Why is the p0505 code still on my Nissan Maxima?

If you have replaced the Idle Air Control Valve on your Maxima and the P0505 code is still present, the source of the problem is the ECM. NOTE: You MUST replace the Idle Air Control Valve with an OEM (Hitachi brand) IACV before reinstallation of the ECM, or immediate damage to the computer will occur!

Why is my ECM still working on my Nissan Maxima?

Often, a failing ECM appears as an Idle Air Control Valve in need of replacement. If you have replaced the Idle Air Control Valve on your Maxima and the P0505 code is still present, the source of the problem is the ECM.

What is the OBD2 code for a Nissan OBDII?

OBDII Nissan Code Definitions. Be sure to double check the codes. Anything P1000 to P1999 or P3000 to P3400 will be Manufacturer specific and may not match the ones listed here. Check specific manufacturer pages on the site, as some of them, we list the OBD2 codes on those pages for those specific vehicles.

How much does it cost to fix Nissan p0403 code?

The cost of diagnosing the P0403 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0403 NISSAN code detected?

Where is the OBD connector on a Nissan Maxima?

A Nissan Maxima’s second-generation On-Board Diagnostic Connector can be found under the dashboard and to the left of the steering column. It will be uncovered, with no access panels blocking it from view. For all Nissans manufactured after 1996, the OBD-II access port is called a Data Link Connector.

What does code 12 on a maxima look like?

Codes come in two-digit numbers, and the codes are conveyed with long and short LED flashes. For example, code 12 is represented by a long flash followed by two briefer ones.

Why is my transmission code not working properly?

The speed sensors tell you how fast your output or input shaft is moving. If the TCM can’t read this information, your speedometer won’t read accurately. The output speed sensor may need to be replaced. These codes all report problems with the gear ratio. The only difference in these transmission trouble codes is the gear that’s being identified.

Navigation