Where are the brake lights on a GMC Yukon?
The most common location is the brake light switch. The good news is they are inexpensive and easy to replace. Your Yukon’s brake light switch is under the brake pedal. It ALWAYS should have power running to it, even if the key is off.
Why are my brake lights not working on my 1997 Chevy?
Pull the plastic cap off the fuse chassis and you’ll see a square relay fuse switch and replace it for the brakes. It’s only $13 bucks and is the predominant issue with 1997 Chevy Trucks and the brakes not working especially if you reverse and blinker lights do work. Was this answer helpful? Its the taillight circuit board or a broken wire.
Where is the fuse on the brake light?
You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights. In case if the fuse is blown, change it with a new one.
Where are the brake lights on a C / K 1500?
There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.
The most common location is the brake light switch. The good news is they are inexpensive and easy to replace. Your Yukon’s brake light switch is under the brake pedal. It ALWAYS should have power running to it, even if the key is off.
Are there any problems with my GMC Yukon?
See all problems of the 2017 GMC Yukon . Brake lights work intermittently. Very dangerous! passenger side brake light, stopped working completely, then came back on. The contact owns a 2015 GMC Yukon. The contact stated that while operating the vehicle, it was discovered that the rear brake lights were inoperable.
Why are my GMC brake lights not working?
There is a design flaw in the 2015 and 2016 models that causes the brake lights to fail. GMC is aware of it and did extend warranty coverage so that if you are “lucky” enough to have them fail with less than 72,000 on your vehicle they will replace them at no cost but after that they will not.
How much does it cost to replace a GMC tail light?
Both of my led tail lamp assemblies have failed over the pas year. GMC has replaced that oem with new parts and has MD the old parts. Generally, if a break light fails you can replace the bulb for around $5 but when these assemblies fail it costs the owner around $700 to replace.
Can a GMC Yukon tail light be repaired?
REPAIR PURCHASES: This is a repair service to the original equipment manufacturer (OEM) GMC Yukon Tail Light assembly’s LED light array. These OEM Yukon Tail Lights were produced by North American Lighting, Inc. (NAL Lighting) and fit the 2015-2018 model years.
Are there any problems with the GMC Yukon?
GMC Yukon Tail Light Repair – we have identified the problem areas of the failed OEM tail lights in the 2015, 2016, 2017, and 2018 GMC Yukon, Yukon XL, and Yukon Denali. We have found that the problem tail lights are most common in the 2015 and 2016, because our customers have told us.
What to do if your brake lights are not working?
If none of the brake lights are working, we are going to follow the circuit from the fuse box back to the brake pedal. At some point the power is not getting from point A to point B. We just have to find where that is. Please note that tail lights can work even if the brake lights are burned out.
Can a brake light switch not be installed?
In many cars, there is a special procedure to remove and install the brake light switch. If not installed correctly, the switch will not operate and can even be damaged. In some cars, the gap between the brake pedal and the switch must also be adjusted.
What is the function of the brake light switch?
The brake light switch serves two major functions. First, it turns on the brake lights when a driver presses the brake pedal. Second, it sends the signal to the vehicle computer that brakes are applied. A car with a faulty brake light switch is UNSAFE to drive.
What are the symptoms of a bad brake light switch?
The most common symptom of a faulty brake light switch is when brake lights don’t come on or stay on all the time. A faulty brake light switch can cause many problems. If a switch is bad, the brake lights won’t operate and the transmission shifter will not come out of “Park” position.
In many cars, there is a special procedure to remove and install the brake light switch. If not installed correctly, the switch will not operate and can even be damaged. In some cars, the gap between the brake pedal and the switch must also be adjusted.
The most common symptom of a faulty brake light switch is when brake lights don’t come on or stay on all the time. A faulty brake light switch can cause many problems. If a switch is bad, the brake lights won’t operate and the transmission shifter will not come out of “Park” position.
There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.