Where are the black wires on a Harley Davidson Softail?
The black wire connects to the main wiring harness ground near the battery. The other three black wires go to the stator. Make sure these wires are all clean and tight. Spray some electric terminal contact cleaner on the connections to promote conductivity. To test the stator, you’ll need a volt meter set to AC volts.
Why are the lights on my Harley Davidson not working?
When you are getting deeper into your troubleshooting project, give yourself plenty of time. Be careful not to disconnect other wiring while you are going through the harness. This is a common occurrence for bikes with aftermarket LED signal lights installed, and may occasionally happen on a standard system.
What kind of wire is on a Harley Davidson headlight?
The pin/socket that was damaged was for a yellow wire, same as the wire on the headlight plug. I bought this bike from the local Harley dealer, it was from the “executive fleet”. The oil in the trans and crankcase was clean, the primary was nasty.
Can a broken turn signal on a Harley Davidson be fixed?
This article applies to the Harley Davidson Touring. A busted or erratic turn signal repair can be a drag to fix, especially on the road. It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night.
What kind of wiring does a Harley Davidson use?
All of its wires and cables connect the battery, alternator, engine control module, and other electrical and electronic components to each other. Without a proper connection, some system may stop working altogether, which is why it is crucial to replace all damaged wires and connectors as soon as possible.
Why is my Harley Davidson Softail not working?
These systems must stay properly powered by the battery. The wiring connecting the systems together must remain intact. These problems occur and, although difficult to find at times, a series of test will help you narrow down the cause. This article applies to the Harley Davidson Softail.
How to check the electrical system on a Harley Davidson Softail?
Record the code number to research possible causes. Press and hold the odometer button to clear the code, and then shut off the ignition to exit the menu. Repeat the process to check the other systems.
Which is the best Harley Davidson Light Bar Connector?
Light Bar Connector by NAMZ®. Designed utilizing the latest technology, this product by NAMZ features premium quality and will perform better than advertised. Perfect for your vehicle and lifestyle, it is manufactured to meet or exceed… Plug and Play Harness by Metra®.
Where are the connectors on a Harley Davidson?
If multiple accessories are connected, it may be advantageous to route the capped 3 and 4-way connectors to the RH side of the vehicle and make the connections on that side. This can be done by removing (325) from the caddy and rerouting it’s branch to the RH side and following the main harness across the top of the starter.
Record the code number to research possible causes. Press and hold the odometer button to clear the code, and then shut off the ignition to exit the menu. Repeat the process to check the other systems.
What does diag stand for on Harley Davidson Softail?
Press and hold the black odometer reset button and turn the ignition switch to the ignition position. Hold the reset button until the message “DIAG” appears. Press and release the odometer button to access the module selection menu. The message “P55PtB” will appear. The letters and numbers stand for the different systems.
The black wire connects to the main wiring harness ground near the battery. The other three black wires go to the stator. Make sure these wires are all clean and tight. Spray some electric terminal contact cleaner on the connections to promote conductivity. To test the stator, you’ll need a volt meter set to AC volts.
Where to find the best Harley Davidson wire connectors?
At Dennis Kirk, you will find the best selection of Harley-Davidson Wire Connectors. We carry more Harley-Davidson products than any other aftermarket vendor and have them all at the lowest guaranteed prices.
Press and hold the black odometer reset button and turn the ignition switch to the ignition position. Hold the reset button until the message “DIAG” appears. Press and release the odometer button to access the module selection menu. The message “P55PtB” will appear. The letters and numbers stand for the different systems.
What does a throttle by wire diagram show?
Harley Davidson Throttle by Wire Diagram – wiring diagram is a simplified usual pictorial representation of an electrical circuit. It shows the components of the circuit as simplified shapes, and the talent and signal links together with the devices.
What are the electrical symbols on a Harley Davidson?
The electrical symbols not lonesome discharge duty where something is to be installed, but next what type of device is swine installed. For example, a surface ceiling spacious is shown by one symbol, a recessed ceiling buoyant has a substitute symbol, and a surface fluorescent vivacious has option symbol.
Where can I download a Harley Davidson manual?
Harley Davidson service manuals for download, free! Lots of people charge for motorcycle service and workshop manuals online which is a bit cheeky I reckon as they are freely available all over the internet. £5 each online or download your Harley Davidson manual here for free!! Have something to add? Come and say hi on Facebook
Harley Davidson Throttle by Wire Diagram – wiring diagram is a simplified usual pictorial representation of an electrical circuit. It shows the components of the circuit as simplified shapes, and the talent and signal links together with the devices.
The electrical symbols not lonesome discharge duty where something is to be installed, but next what type of device is swine installed. For example, a surface ceiling spacious is shown by one symbol, a recessed ceiling buoyant has a substitute symbol, and a surface fluorescent vivacious has option symbol.
Harley Davidson service manuals for download, free! Lots of people charge for motorcycle service and workshop manuals online which is a bit cheeky I reckon as they are freely available all over the internet. £5 each online or download your Harley Davidson manual here for free!! Have something to add? Come and say hi on Facebook
How many Harley wiring harnesses are left in stock?
Only 17 left in stock – order soon. . Only 2 left in stock (more on the way). . Only 3 left in stock – order soon. . . Only 14 left in stock – order soon.
What should battery voltage be on Harley Davidson Softail?
Attach the positive voltmeter lead to the positive battery post and the negative to the negative. The battery should read above 12.2 volts. If your Softail will start, keep the voltmeter connections in place and start the engine. The charging system should now be working and battery voltage should increase to above 14 volts.
These systems must stay properly powered by the battery. The wiring connecting the systems together must remain intact. These problems occur and, although difficult to find at times, a series of test will help you narrow down the cause. This article applies to the Harley Davidson Softail.
What causes a Harley Davidson battery to go bad?
The most common cause of electrical problems on a Harley Davidson is the battery or the voltage regulator. Troubleshooting can be performed in any garage, and it saves on expensive service bills.
Can a battery be replaced on a Harley Davidson Softail?
If you notice your bike consistently taking longer to start, battery inspection and replacement is a good idea. This article applies to the Harley Davidson Softail. The battery creates electricity by continuous chemical reactions. Electrolyte inside the battery reacts with the metal plates to generate electrons.
What causes no start on Harley Davidson Softail?
A parasitic draw occurs when one or more circuit remains powered after the ignition is turned off. A draw on the battery of more than 0.02 amps can deplete the battery overnight enough to create a no start problem. To test for a parasitic draw, place your multimeter to the amps setting in series with the battery.
Why does my 84 flhtc battery keep draining?
I believe I have a battery drain. Just purchased a new 350 cold crank amps and after a proper initial charge, and run, the next day the battery did not have enough juice to turn over. My 84 FLHTC has the EVO motor, and while it runs and sounds like a dream, starting it has become a issue. Any ideas?