When to use crankshaft to camshaft timing marks?

This answer was rated: nissan: crankshaft to camshaft timing marks when fitting a… crankshaft to camshaft timing marks… crankshaft to camshaft timing marks when fitting a new timing chain on a z24 nissan nomad motor?. links between marks on new chain/

How to set timing chain on camshaft sprocket?

Set timing chain by aligning its mating marks with those of crankshaft sprocket and camshaft sprocket, Fig. 17. b. Camshaft sprocket should be installed by fitting knock pin of camshaft into its No. 2 hole, Fig. 17, and No. 2 timing mark must also be used.

What are the timing marks on a Kohler command engine?

This feature is not available right now. Please try again later. In this video I show you the Camshaft & Crankshaft Timming Marks on a Kohler Command Engine. The engine in the video is a 12.5 HP but the same procedure will apply to many other Kohler engines. http://www.youtube.com/user/donyboy73… Loading…

When to use timing marks on a nomad?

Crankshaft to camshaft timing marks when fitting a new timing chain on a z24 nissan nomad motor?. links between marks on Crankshaft to camshaft timing marks when fitting a new timing chain on a z24 nissan nomad motor?. links between marks – Answered by a verified Nissan Mechanic

When does a cam line up with the crankshaft?

How does advancing or retarding a camshaft work?

Advancing or retarding the cam pushes the centerline of the camshaft to one side or the other of the crankshaft centerline. This changes the Timing of the valve opening and closing events, in relation to the position of the piston in the cylinder. How is it measured? Find the lobe centerline in relation to the piston’s position in the cylinder.

How do you find the lobe of a camshaft?

Find the lobe centerline in relation to the piston’s position in the cylinder. This is known as “degreeing the camshaft.” This should be done when building an engine or replacing a camshaft. Follow this link for the process to Degree the Camshaft. Compare the centerline to the value listed on the Cam Card .

What happens when a cam is installed straight up?

When a cam is installed “straight-up,” the imaginary centerlines of the two shafts line up exactly. Advancing or retarding the cam pushes the centerline of the camshaft to one side or the other of the crankshaft centerline. This changes the Timing of the valve opening and closing events, in relation to the position of the piston in the cylinder.

How to get timing marks on a Nissan?

1. Disconnect battery ground cable. 2. Drain coolant from radiator, being careful not to spill coolant on drive belt s. 3. Remove radiator. 4. Remove cooling fan. 5. Remove drive belts. 6. Set No. 1 cylinder at top dead center (TDC) on its compression stroke. 7. Remove power steering pump, idler pulley and power steering brackets. 8.

What’s the best way to set the cam timing?

Rotate crank until the rockers on cylinder one are holding both valves open a little. This is the overlap period and how you are going to set the cam timing. Look at the pointer and pulley. Rotate crank to set them so they are directly opposite each other.

What’s the best way to timing an engine?

Assemble the cylinder head, rocker gear, etc. as you are going to run the engine. Torque it all down, set the valve clearances as suggested by the manufacturer, but do not fit the rocker cover. Rotate crank until the rockers on cylinder one are holding both valves open a little.

Do you have to change the timing gears on a cam?

After each adjustment of the timing gears, you need to go back and repeat steps 4,5 and 6 as altering the cam timing will alter the big gaps between rocker and valve tip. This method initially restricts timing to the manufacturers recommendations.

Where do you put the timing disc on a camshaft?

It is always recommended to calculate the actual position of TDC rather than rely on the mark on the crank pulley. Fit the timing disc to the front of the crankshaft. A pointer for the timing disc can be made from a piece of bent wire secured under a suitable front cover bolt. Position a dial gauge to measure the travel of No 1 piston (see right).

How do you make a timing mark on a cam?

Put a bolt in the central one, head down with a couple of washers between it and the plate. Secure it with a nut on top. That’s your stop plate. The pointer is worth making permanent as it makes a super-accurate ignition timing mark, so use a strip of metal or really stout wire.

Where is the timing mark on a crank pulley?

You can also shut off the engine in this way. On most crank pulleys, there is another mark. This is the mark you aim for, usually somewhere between 3-5 degrees before Top Dead Center. All you do is turn the distributor until that timing mark is flashing at the right spot every time.

Where is the No.1 Mark on the crankshaft?

With the distributor cap removed, the rotor should be pointing toward the No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch on the crankshaft pulley should align with the dot on the intermediate shaft sprocket.

Where are the timing marks on a VW?

Make sure that the camshaft and crankshaft timing marks are aligned. Install the timing belt, with the arrow pointing in the direction of rotation, on the crankshaft sprocket, the water pump sprocket and the camshaft sprocket. Install the lower and center timing belt covers.

Navigation