When did the Mazda Protege repair manual come out?
We’ve checked the years that the manuals cover and we have Mazda Protege repair manuals for the following years; 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 1999, 2000, 2001, 2002 and 2003. Go through the 48 different PDF’s that are displayed below, for example this one.
What kind of wiring diagram does a Mazda 626 have?
Mazda 626 wiring diagrams car ge diagram 2002 1999 1998 2001 1996 1990 ignition system Mazda 626 Wiring Diagrams Car Electrical Diagram Mazda 626 Ge Wiring Diagram Page Lease Freeze Faipingconsvitol It Mazda 626 Wiring Diagrams Car Electrical Diagram 2002 Mazda 626 Wiring Diagram Export Stale Suitcase Congressosifo2018 It
What are the different types of Mazda repair manuals?
Our Mazda Automotive repair manuals are split into five broad categories; Mazda Workshop Manuals, Mazda Owners Manuals, Mazda Wiring Diagrams, Mazda Sales Brochures and general Miscellaneous Mazda downloads. The vehicles with the most documents are the 2, 5 and Protege.
When did Mazda stop making the Mazda 323?
It was manufactured with both manual and automatic transmission styles. After eight generations of this vehicle, its production ended on October 2, 2003 and the whole Familia line were replaced by the Mazda3 in early 2004.
How many manuals are there for a Mazda Protege?
We have 48 Mazda Protege manuals covering a total of 14 years of production. In the table below you can see 0 Protege Workshop Manuals,0 Protege Owners Manuals and 4 Miscellaneous Mazda Protege downloads. Our most popular manual is the 1999-2000–Mazda–Protege–4 Cylinders 1.6L MFI DOHC–32533801 .
How to remove the cylinder switch from a Mazda Protege?
ECT sensor signal characteristic (reference) Circuit Open/Short Inspection fPage 210 Door Lock Cylinder Switch: Service and Repair DOOR KEY CYLINDER SWITCH REMOVAL/INSTALLATION 1. Close the door glass completely. 2. Disconnect the negative battery cable. 3. Remove the passenger-side front door trim.
What do you need to know about Mazda wiring?
These Mazda Wiring information / Aftermarket Autostart/Alarm Technical Wiring Diagrams are very useful, if not required, for the installation of alarms, autostart / alarms, remote starts, doorlock info and any other aftermarket installation that would require you to know the / Wire Information / Wiring Information of your Mazda
How to change the ECT sensor on a Mazda Protege?
Place the ECT sensor in water with a thermometer, and heat the water gradually. Specification 4. Measure the resistance between the ECT sensor terminals A and B using an ohmmeter. – If not as specified, replace the ECT sensor.
Where is the fuel pump located on a Mazda Protege?
The Mazda Protege uses an in-tank fuel pump assembly coupled with the fuel sending unit. Some in-tank fuel pumps are difficult to replace, because the fuel tank needs to be removed. However, the Protege has a convenient fuel pump access door mounted beneath the rear seat, which makes the process fairly easy compared with some other vehicles.
How do you relieve fuel system pressure in a protege?
Crank the Protege’s engine to begin relieving the fuel system pressure. Remove the rear seat cushion by pulling the straps protruding from beneath the seat. Remove the Phillips-head screws from the fuel pump access cover. Lift the cover away. Disconnect the visible electrical connection attached to the fuel pump access cover.
When do you remove the seat cushion on a protege?
The procedure is applicable to all Protege model years from 1990 to 1998. Crank the Protege’s engine to begin relieving the fuel system pressure. Remove the rear seat cushion by pulling the straps protruding from beneath the seat. Remove the Phillips-head screws from the fuel pump access cover. Lift the cover away.
When did the Mazda Familia come out in Europe?
The Mazda Familia, also marketed as the Mazda 323 and the Mazda Protegé, is a small family car that was manufactured by Mazda between 1963 and 2003. In Europe, all models after 1977 were called 323.
Why does my Mazda Protege crank but not start?
It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days. Mine was clogged when I was on vacation and mine would crank but would not start.
What to do if your Mazda3 won’t start?
One way to do this is to start your car and let the engine run for a while to recharge the battery. One thing to know: if the battery is over 4-5 years old, it may be completely dead, so it will not recharge and the car will not restart after you turn it off. In this case, you may need a new battery.
Why does my Mazda Protege make no noise?
Does it start when you try jumping it. It can also be a bad starter although this will normally have a clicking noise or no noise instead of a cranking noise. It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days.
Where is the ignition switch on a Mazda 3?
An ignition switch is an electrical switch installed on the rear of the ignition lock mechanism. If shaking the key in the ignition switch helps to start the car, you should check the ignition switch first. The starter solenoid control wire may have a bad connection.
ECT sensor signal characteristic (reference) Circuit Open/Short Inspection fPage 210 Door Lock Cylinder Switch: Service and Repair DOOR KEY CYLINDER SWITCH REMOVAL/INSTALLATION 1. Close the door glass completely. 2. Disconnect the negative battery cable. 3. Remove the passenger-side front door trim.
What kind of inspection should I do on my Mazda Protege?
Always carry out a total inspection of the Input systems, output systems, and PCM to determine the cause of trouble. Otherwise, a wrong diagnosis will be made. PCM Inspection Using the SST (104 Pin Breakout Box) 1.
How do you check the PCM on a Mazda Protege?
PCM Inspection Using the SST (104 Pin Breakout Box) 1. Disconnect the negative battery cable. 2. Disconnect the PCM connector. 3. Connect the SST (104 Pin Breakout Box) to the PCM as shown. 4. Tighten the connector bolt. Tightening torque 7.9 – 10.7 N.m {80 – 110 kgf.m, 69.5 – 95.4 in.lbf} 5. Connect the negative battery cable.
We’ve checked the years that the manuals cover and we have Mazda Protege repair manuals for the following years; 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 1999, 2000, 2001, 2002 and 2003. Go through the 48 different PDF’s that are displayed below, for example this one.
What kind of engine does a Mazda Protege have?
Except for the MP3, all models now use a 130-hp, 2.0-liter four-cylinder engine designed by Mazda. The 1.6-liter engine, previously standard on the DX sedan, has been dropped. Each 2002 vehicle benefits from a reinforced body/chassis structure, and a new modular audio system with a standard CD player is installed in all sedans.
How many passengers does a Mazda proteg hold?
As a result of what Mazda calls OptiSpace design, the Proteg� can actually accommodate the five passengers that it claims to hold. Interior volume amounts to 92.6 cubic feet, and it has adequate rear legroom and headroom for adult passengers.
Is the 2002 Mazda Protege a Ford Focus?
Each 2002 vehicle benefits from a reinforced body/chassis structure, and a new modular audio system with a standard CD player is installed in all sedans. A redesign isnt likely until 2004, but when it does occur, the Ford Focus platform may possibly be used. Ford owns a controlling interest in Mazda.