When did the Jeep 42RE transmission come out?

The 42RE was first used in Jeep Cherokee vehicles in late 1993, until it was replaced by the 42RLE in 2004. It is a four speed, automatic overdrive, electronically controlled transmission, which differs from the 42RH transmission because of the hydraulic control.

Are there any problems with the Jeep 42RLE?

(like RPM out of control and other serious matters) Jeep don’t want a 10billion buck lawsuit like Toyota has, no way. So you must scan it, not with a $10 fleabay scanner, but with this tool (or the like), theINNOVA 3160 scannersee’s ALL YOU CAN SEE. P17xx codes, U, B,P,C and P1 and P2xx codes.

Where to find the part number on a 42RE transmission?

Look for the transmission part/identification number and date code. According to the 42RE service manual on Scribd.com, the codes are located on the driver’s side of the transmission, stamped just above the oil pan gasket surface. The first group is the assembly part number, followed by the manufacturing date.

Is there a 2.7 CRD diagnostic tool for Jeep Grand Cherokee?

Many of our customers have a huge problem with reading out Jeep Grand Cherokee 2.7 CRD fault codes. It is possible to see engine fault codes with key on-off method, but you can not clear faults without correct OBD diagnostic tool. Also disconnecting battery will not clear fault codes on 2.7 CRD Jeep Grand Cherokee.

When was the Jeep NP242 transfer case introduced?

The Jeep NP242 transfer case was introduced in the 1987 model year as a replacement for the NP228. The 242 premiered in the XJ Cherokee / Wagoneer and MJ Commache as the SelecTrac option.

Is the Jeep 242 good for factory transmissions?

The Jeep 242 is found behind these factory transmissions: Adaptation to better transmissions is often less costly than rebuilding the weaker Jeep gearboxes and provides serious performance and strength upgrades. The 242 adapts very well to several popular transmissions, including:

Is it safe to drive a Jeep Grand Cherokee with transmission fluid leaking?

If your Jeep Grand Cherokee’s transmission is leaking directly from the transmission pan (far and away the most common area), than it is safe to drive. it should still be fixed right away. Enough transmission fluid leaking anywhere can be dangerous.

Can a pan gasket leak on a Jeep Grand Cherokee?

The leak can easily be mis-diagnosed as a leaky pan gasket. A lot of unsuspecting consumers may end up spending a thousand dollars or more to rebuild a transmission with a leak like this. There’s no recall at this time from Chrysler, perhaps there should be, with such a widespread problem.

Is there a problem with my Jeep Grand Cherokee?

Very often, this will solve the problem. But Jeep Grand Cherokees seem especially prone to more serious transmission problems, and some owners are quite vexed at their inability to determine the causes.

Where is the transmission located on a jeep?

The transmission is generally located under the front seats, slightly forward of the middle of the vehicle. Access the transmission from the driver’s side. Count the number of bolts attaching the pan to the transmission’s underside.

Can a Jeep Grand Cherokee Drive in two gears?

You’re often still able to drive the vehicle, but it only operates in one or two gears. For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually.

What happens when the Jeep Grand Cherokee is in overdrive?

If the transmission fluid temperature sensor reports an overheating condition (over 260 degrees F) and the transmission is currently in overdrive, the TCM will downshift to third gear. The TCM will also light the LED in the dash-mounted OD off switch until the temperature drops below 230 degrees F.

When did Jeep start using The 42RE transmission?

What is the OD on a Jeep Grand Cherokee?

The OD inputs are overdrive off switch, TPS, VSS, transmission temp sensor, output speed sensor and engine rpm. The torque converter clutch (TCC) solenoid will normally operate in overdrive, but the TCM can operate the TCC in third gear if the overdrive off switch is selected.

What kind of transmission does a Jeep Grand Cherokee have?

44RE: A four speed automatic transmission was used in 1996 to 1998 Jeep Grand Cherokee’s with 5.2L engines. 42RE: A four speed automatic transmission was used in 1993.3 to 1998 Jeep Grand Cherokees with 4.0L engines.

What’s the gear ratio on a Jeep Grand Cherokee?

44RE: A four speed automatic transmission was used in 1996 to 1998 Jeep Grand Cherokee’s with 5.2L engines. Gear Ratios: 1st Gear: 2.74:1, 2nd Gear: 1.54:1, 3rd Gear: 1.00:1, 4th Gear: .69:1, Reverse Gear: 2.20:1 42RE: A four speed automatic transmission was used in 1993.3 to 1998 Jeep Grand Cherokees with 4.0L engines.

What kind of transmission does a Jeep Comanche use?

AW4: A four speed automatic transmission was used in 1987 to 2001 Jeep Cherokee (XJ), & Jeep Comanche with 2.5L & 4.0L engines. It was also used in 1987 through 1992 Jeep Comanche & 1993 through 1993.5 Jeep Grand Cherokee with 4.0L engines.

What’s the gear ratio on a 42RE transmission?

The transmission also featured a transmission temperature-control system that worked in tandem with the radiator temperature sensor to keep the transmission cool. The 42RE and 42RH had the same gear ratios: 2.74-to-1 for first, 1.54-to-1 for second, direct 1.00-to-1 for third and 0.69-to-1 for fourth.

Is there a warranty on a 42RE transmission?

The Best Warranty. A Re-Manufactured 42RE Transmission For The Price Of A Rebuild. Each 42RE Is Engineered To Exceed OEM Specification. Nationwide Warranty. Not Used. Not Rebuilt. Re-Manufactured. Pictured below are just a few of the Updates & Upgrades that go into each 42RE Transmission.

Is there an automatic transmission on a Jeep Grand Cherokee?

Keep that engine running smoothly by regularly checking transmission fluid and visiting AutoZone for Jeep Grand Cherokee automatic transmission parts. Unlike manual transmissions, automatic transmissions shift gears on their own as your vehicle moves.

What kind of transmission does a 1997 Jeep Cherokee have?

There are alternate names for the transmissions used on 1997 Jeep Cherokees. The AW4 is also referred to as the A340, the 30RH as the A904, the 46RH as the A518 and the 42RE as the A500. These are Chrysler’s designations for these transmissions.

Where are the transmission numbers on a Jeep Cherokee?

Step 1 Access the Jeep Cherokee’s transmission by looking underneath the Cherokee. Identification numbers for the AW4 and 30RH are located on the passenger’s side while 46RH and 42RE numbers are on the driver’s side of the transmission. Locate the transmission’s identification numbers.

Is the Grand Cherokee available with a manual transmission?

Hi, Mario…The Grand Cherokee with a 4.0L was actually available with a manual transmission though that is very rare. You need to find a “donor” XJ Cherokee with a 5-speed AX15 manual transmission and compare this with your Grand Cherokee. The XJ Cherokee is much more popular and shares parts with the Grand Cherokee.

How much does a rebuilt 42RLE transmission cost?

Core Deposit: $500.00 Far from just being rebuilt, the Xtreme Performance series 1 is an OEM replacement that has been fully remanufactured with upgraded parts that have been designed to increase performance, reliability and longevity. Our 42RLE transmission sale is here.

When did the Dodge 42RLE 4 speed automatic come out?

The Chrysler Corporation built this 4 speed automatic for Jeep applications starting in 2000. As the 42RLE’s popularity began to grow Dodge, Mitsubishi and Chrysler began to use this transmission in a wide variety of car, truck and SUV applications.

Can You bolt up a 42RE Jeep Dakota?

Yes it will bolt up. They use the 42re behind 4.0L I6’s in Jeeps, and behind the 3.9L V6 (318 minus 2 cylinders) in the Dakota. Are you sure its a 42RE and not a 44RE. I didn’t think they put a 42RE behind the 318, I thought they always used the 44RE oke: I don’t know to be honest. It is just a Grand Cherokee with 5.2L and an auto…..

What kind of transmission does a Jeep Grand Cherokee use?

Jeep Grand Cherokee started using the 42RE transmission in 1993 1/2 models with the 4.0L engine. The “4” stands for 4-speed, “2” is for torque capacity, “R” is for rear-wheel drive, and “E” is for electronically controlled. This transmission is electronically controlled using a governor pressure solenoid to vary the governor pressure.

What kind of transmission does a Jeep Liberty use?

The 42RLE transmission was not only used in the Jeep Liberty, it was also used in the Jeep JK Wranglers (2007 to 2013) and the TJ/TJL Wranglers (2003 to 2006). The transmissions are known to have some quirky problems now and then, and given how much they rely on electronics, that’s not surprising.

Do you need transmission fluid in a 42RLE transmission?

The transmissions are known to have some quirky problems now and then, and given how much they rely on electronics, that’s not surprising. One important thing is that you must use the correct transmission fluid in a 42RLE transmission.

How often does a jeep transmission come out?

There you have it! A chronological history of transmissions for Jeeps (for you history buffs out there). Nearly every year new transmissions or improved older designs hit the market, and there is no reason to expect that currently available transmissions will not be discontinued at some point.

What kind of transmission does a jeep 909 have?

The 909 is a 904 with a lock-up torque converter. SR-4, T-4: The SR-4 and T-4 are light duty four speed manual transmissions used in CJs from 1980 until 1986. T-176, T-177, T-178: The T-176, T-177, and T-178 are a medium duty four speed manual transmission used in Jeep CJs, SJs, and J pickups from 1980-1986.

Is the A500 42RE transmission available for sale?

The A500 42RE was specifically designed for Dodge Ram, Dakota, Durango and Jeep Grand Cherokee vehicles with 3.9 and 4.0 liter engines. For a limited time, when you purchase our 42RE transmission we will throw in a performance lockup torque converter and Hayden internal cooler for free. Core Deposit: $500.00

What kind of transmission does Dodge A500 use?

When did the Dodge A500 42RE come out?

The 42RE was used in Dodge and Jeep applications from 1982 through 2004. 42RE is the first of its series to feature an electronically controlled overdrive. The A500 42RE was specifically designed for Dodge Ram, Dakota, Durango and Jeep Grand Cherokee vehicles with 3.9 and 4.0 liter engines.

11-01-2007, 03:32 AM Jeep Grand Cherokee started using the 42RE transmission in 1993 1/2 models with the 4.0L engine. The “4” stands for 4-speed, “2” is for torque capacity, “R” is for rear-wheel drive, and “E” is for electronically controlled.

The 42RE is a 4 speed automatic overdrive transmission. The 42RE 4 speed automatic transmission was used in 1993.5 to present Jeep Grand Cherokees with 4.0L engines.

Introduced in the early 1990s, it was used in trucks, vans, and Jeep Grand Cherokees equipped with a 5.9 Liter V-8. The most important thing to know, when trying to troubleshoot a transmission problem, is that the 42RE, 44RE, or 46RE automatic transmission usually fails in one of two ways: Transmission is ‘slipping’.

When does the transmission shift out of 2nd gear?

Transmission does not shift out of 2nd gear. This generally happens when the PCM senses an electrical problem and commands the transmission to stay in what is known as ‘Limp In Mode’. In ‘Limp In Mode’, the automatic transmission will not downshift or upshift at all.

Navigation