What to do with timing belt on accord?
With the balance belt out of the way, loosen the just-installed bolt. Move the tensioner to release tension and snug the bolt. With the belt removed, check or replace the seals and water pump and install a seal retainer. Installing a retainer plate holds the balance shaft seal in place.
How do you install a balance belt on a Honda Accord?
The balance belt installation is more of the same. Loosen the tensioner adjustment nut to allow the tensioner pulley to be moved out of the way. Install the belt using your marks or the alignment pin. Loosen the adjuster to allow the tensioner to work, rotate the crank one turn and tighten the adjustment nut.
What’s the best way to tension a timing belt?
Take up any loose slack in the timing belt by adjusting the center to center distance between the two timing belt pulleys. Before any final tensioning is to be applied make sure that the timing belt teeth are fully seated in the tooth grooves on both timing belt pulleys.
How do you tension a power transmission belt?
First determine the proper deflection force required to tension the timing belt. Deflection forces are given in the timing belt manufacturer’s tables and/or power transmission drive design online calculators. Then place a straightedge across the top of the timing belt.
How do you adjust the timing belt on an accord?
Before you loosen the adjustment nut that will relieve the tension off both belts, install and tighten a short 6 mm bolt in the adjustment slot (the dipstick tube bolt works well) to maintain tension on the timing belt while you remove the balance belt. With the balance belt out of the way, loosen the just-installed bolt.
The balance belt installation is more of the same. Loosen the tensioner adjustment nut to allow the tensioner pulley to be moved out of the way. Install the belt using your marks or the alignment pin. Loosen the adjuster to allow the tensioner to work, rotate the crank one turn and tighten the adjustment nut.
How do you install a new timing belt?
Shorten the center distance or release the tensioning idler to install the timing belt. Do not pry the timing belt onto the timing belt pulleys. Place the timing belt on each timing belt pulley and ensure proper engagement between the timing belt pulley and timing belt teeth.
How do you tension a timing belt pulley?
Place the timing belt on each timing belt pulley and ensure proper engagement between the timing belt pulley and timing belt teeth. Lengthen the center distance or adjust the tensioning idler to remove any timing belt slack. Using a tape measure, measure the span length of the drive in inches. Refer to dimension “P” in the diagram above.
How to remove timing belt and timing balancer?
Timing tensioner. Before moving on to the next step, it’s wise to drain the coolant. Place a pan under the car, and turn the petcock on the bottom of the radiator to release. Now that the coolant has been drained and the timing belt as well as the balancer have been removed, the water pump can come out. Remove the bolts in red (Figure 12).
Where are the TDC marks on the timing belt?
TDC marks are in red (Figure 10). Loosen the adjusting nut in red (Figure 11). Push belt tensioner down. The yellow in Figure 11. Tighten the adjusting nut, and remove the timing belt. Figure 10. Timing belt TDC marks.
What do timing belts and water pumps do?
Timing belts and water pumps are wear items. They need regular servicing, and are critical components to the longevity of your vehicle. One controls how the motor stays in sync under operation, while the other one controls how effectively the motor is cooled.
How often should the timing belt be replaced on a Honda Accord?
As per Honda, your timing belt needs to be serviced every 50,000 to 80,000 miles. While you’re in there, there are a few other important things to address like the timing balancer and the water pump. This article will guide you through the process of replacing the timing belt, timing balancer, and the water pump on your Accord.
Timing tensioner. Before moving on to the next step, it’s wise to drain the coolant. Place a pan under the car, and turn the petcock on the bottom of the radiator to release. Now that the coolant has been drained and the timing belt as well as the balancer have been removed, the water pump can come out. Remove the bolts in red (Figure 12).
TDC marks are in red (Figure 10). Loosen the adjusting nut in red (Figure 11). Push belt tensioner down. The yellow in Figure 11. Tighten the adjusting nut, and remove the timing belt. Figure 10. Timing belt TDC marks.
Timing belts and water pumps are wear items. They need regular servicing, and are critical components to the longevity of your vehicle. One controls how the motor stays in sync under operation, while the other one controls how effectively the motor is cooled.
How to change timing belt on Acura water pump?
Old water pump compared to new water pump. Install the new timing belt tensioner bearing, balance shaft tensioner bearing, tensioner bolt (finger tight), and the timing belt tensioner bearing spring. Push down the timing belt tensioner bearing to extend the bearing spring and tighten the tensioner bolt.
Can A P / s bolt be removed from a Honda Accord?
Figure 3. P/S bolt and tensioner. The power steering pump can be removed from its bracket to gain more room. The hoses do not need to come off. The alternator as well as its related belt will need to come off in order to gain more clearance to the timing belt and water pump.
Figure 3. P/S bolt and tensioner. The power steering pump can be removed from its bracket to gain more room. The hoses do not need to come off. The alternator as well as its related belt will need to come off in order to gain more clearance to the timing belt and water pump.