What to do if your Navi button is not working?

Press NAVI button and wait for the system to restart. If that doesn’t work go to the next step. Try resetting the COMAND system by removing the fuse for 15 minutes. Reinsert the fuses and check if the error message is gone. Check all the cables and connections in the back of the COMAND or the DVD drive.

What to do when your navigation system is not activated?

If you are trying to update the navigation system using an update DVD you may get an error message saying Loading Navigation. This process can take a while in some cases up to one hour. Try removing the Navi DVD, turn off your car and let it sit for one hour.

How do you change the radio in a Honda Pilot?

Pull the instrument cluster trim panel towards the rear of vehicle and remove it, then carefully pry around the perimeter of the radio trim panel to release the retaining clips. Set the trim panel to the side, remove the four Phillips screws securing the radio, then disconnect the harnesses and remove the radio.

Why does my Honda navigation say no DVD installed?

Honda or Acura Navigation often gives error code despite having right DVD in the system. Usually says No DVD Disk Installed or Door Open. Video shows an easy repair to this very common problem by addressing one possible source of error code. Please Share and Subscribe! Loading…

Why is my Navi CD not working properly?

Make sure the Navi disk itself isn’t damaged. If your stereo has only one slot for the Navigation DVD and audio CD, try inserting an audio CD or DVD to see it that works properly. If it does then the problem may be your disk and not the optical lens.

Why is my navigation system not working properly?

It is possible that one of the cables in the back of the unit has gotten loose or is disconnected. Another common error message that you will see is “Navigation is initiating please wait” Under such conditions the COMAND system works correctly except the navigation system. Here are a few possible causes and solutions to this problem.

What should I do if my computer audio is not working?

Windows has a dedicated audio services component that is responsible for playing all kinds of sounds on the system. Therefore, you can just restart the audio services on your system to troubleshoot the computer audio not working. Just go to the Start menu, launch the Run prompt, and enter the “msc” command.

What causes the navigation screen to stop working?

Alll of your problems is being cause by the navigation driver assy module it is rigth behind the screen pull the top dash bezel off get the model number look on ebay has to be the same model number 4 screws and 2 wire pugs and your problems fixed for anyone with a blank screen with the back light dim on the screen.

Why is my Nav screen not working on my Armada?

I too have similar problem with the recent 2005 Armada I just bought. Nav/GPS/Radio Screen that shows the reverse Camera is not getting power. The AC panel works, but the Nav/GPS screen does not turn on. DVD does not power too. it doesnt turn on at all.

How do I get my Acura navigation code?

You will be requested to provide your current number and zip code. Also, by providing an email address, a confirmation with the requested code will be sent to you for your records.

Why is my Mercedes navigation not working properly?

All the units which are part of the fiber optic need to be in proper working condition. If your Mercedes uses a separate drive for the NAVI DVD, it is possible that this unit can be defective. Learn more about fiber optic problem by reading Mercedes Audio System Explained. The DVD drive that holds your navigation disk could be damaged.

How does the navigation system work on a Mercedes Benz?

From finding the nearest ATM when traveling around town, to locating a nearby fuel station on your next road trip, an optimized navigation system will help you drive with confidence and ease. Remember, your Mercedes-Benz navigation system is designed for driving.

What was the rating of the Mercedes Benz CLS?

5 average Rating out of 3 reviews. Sitting on the Mercedes-Benz stand at the Geneva Motor Show back in 2004, the first CLS astonished styling critics. Even die-hard two-seater fans liked its radical new four-door coupe design.

What does it mean when Mercedes says navigation cannot be activated?

After inserting the navigation DVD in your Mercedes-Benz COMAND, you get a warning message “Navigation Cannot Be Activated.” You press the NAVI button on the COMAND but get an alert message saying “”Navigation can not be activated. An error has occurred.” N1112 No data transfer between D2B master and D2B predecessor component possible.

How to test button control in Microsoft Docs?

Press F5, and then test the app by adding several numbers together. Add a second button to clear the total between calculations. Add another Button control, set its Text property to “Clear”, and set its OnSelect property to this formula: Press F5, add several numbers together, and then click or tap Clear to reset the total.

How to soft reset COMAND / nav radio system?

How to perform a soft reset of the COMAND / NAV Radio System. Find the fuse box under the dashboard. Pry the side cover, look for fuse 26 and 28 and remove both fuses. The second fuse box may be on the left side of the trunk. Locate and remove fuse 6. Take out the key from the ignition and don’t turn on the car for at least 15 minutes.

How to fix a Mercedes Benz navigation system?

Doing a soft reset for these systems will force the head unit to rest. This normally restores the systems to working order. Chances are the symptoms may return. If this happens repeatedly, a professional Mercedes Benz repair technician or mechanic can help check any updates for your COMAND / navigation unit. Find the fuse box under the dashboard.