What should I do about my Hyundai Sonata cylinder head?
Repair procedures Hyundai Sonata YF 2011-2014 Service Manual / Engine Mechanical System / Cylinder Head Assembly / Cylinder Head. Repair procedures Use fender covers to avoid damaging painted surfaces. To avoid damaging the cylinder head, wait until the engine coolant temperature drops below normal temperature before removing it.
Why does my Hyundai Sonata make a clicking noise?
If your Hyundai Sonata won’t start and make some clicking noises, this indicates a drained battery. Sometimes your battery might have enough charge to make the clicking noise, but this charge depletes immediately after the starter requests some electrical current. Hyundai Sonata won’t start, but the battery is good
What to do if your Hyundai Sonata won’t start?
If your Hyundai Sonata won’t start, the problem is related to the battery, the battery terminals, the key fob battery, the starter, the alternator, the fuel filter, the fuse, the spark plug, or the engine. Auto Repairs Are EXPENSIVE Hyundai Sonata is one of the top-ranked midsize vehicles that attract tons of customers every year.
How big is the intake valve on a Hyundai Sonata?
Using a caliper gauge, measure the inside diameter of the valve guide. Intake / Exhaust : 5.500 ~ 5.512mm (0.21654 ~ 0.21701in.) Using a micrometer, measure the diameter of the valve stem. Intake : 5.465 ~ 5.480mm (0.21516 ~ 0.21575in.)
What’s the best way to remove a cylinder head?
Remove the cylinder head. Using triple square wrench, uniformly loosen and remove the 10 cylinder head bolts, in several passes, in the sequence shown. Remove the 10 cylinder head bolts and plate washers. Head warpage or cracking could result from removing bolts in an incorrect order.
How to repair a Hyundai Santa Fe cylinder head?
Lift the cylinder head (A) from the dowels on the cylinder block and place the cylinder head on wooden blocks on a bench. Be careful not to damage the contact surfaces of the cylinder head and cylinder block. Remove the cylinder head gasket (B).
How do you get coolant out of a radiator?
Remove the radiator cap and attach the air pump’s tester hose to the coolant recovery tank. Now, you can start pumping in the air until the air pump’s gauge reaches the level of pressure printed on the radiator.
Repair procedures Hyundai Sonata YF 2011-2014 Service Manual / Engine Mechanical System / Cylinder Head Assembly / Cylinder Head. Repair procedures Use fender covers to avoid damaging painted surfaces. To avoid damaging the cylinder head, wait until the engine coolant temperature drops below normal temperature before removing it.
Lift the cylinder head (A) from the dowels on the cylinder block and place the cylinder head on wooden blocks on a bench. Be careful not to damage the contact surfaces of the cylinder head and cylinder block. Remove the cylinder head gasket (B).
Remove the cylinder head. Using triple square wrench, uniformly loosen and remove the 10 cylinder head bolts, in several passes, in the sequence shown. Remove the 10 cylinder head bolts and plate washers. Head warpage or cracking could result from removing bolts in an incorrect order.
What to do if cylinder head bolts are stuck?
If it is stuck, tap lightly on the side of the head with a rubber hammer to loosen the cylinder head. Warning: Most head bolts are torque-to-yield. These head bolts are single use only and once removed must be replaced.
Using a caliper gauge, measure the inside diameter of the valve guide. Intake / Exhaust : 5.500 ~ 5.512mm (0.21654 ~ 0.21701in.) Using a micrometer, measure the diameter of the valve stem. Intake : 5.465 ~ 5.480mm (0.21516 ~ 0.21575in.)
How much torque does a Hyundai Sonata 2.0 have?
This is the head gakset torque specification for a 2011 and 2012 hyundai sonata 2.0 and 2.4L engine. Torque the head bolts in several passes. First torque to 23.9 to 26.8 foot pounds. Next, turn the bolts to 90 to 95 degree and again to 90 to 95 degree. Remember to use brand new head bolts and lubricate the new head bolts with fresh engine oil.
When was the cylinder head gasket replaced on my Hyundai?
Bought new a 2006 Hyundai Terracan CRDi 2.9. Had a new pinion seal and nut replaced at 86000ks service. We now have a loud whine at 70-100ks. this noise has only happened since the servise. Can you gi … read more I have a Hyundai Sonata 2lt GL (1997 model) and had the cylinder head gasket replaced.
How do you change the head gasket on a Hyundai?
Oil the new cylinder head bolts with clean motor oil. Lower the new gasket on to the engine block and align the dowel pins. Assure the number one cylinder of the engine is set to top dead center. Torque the new bolts in the correct tightening sequence.
This is the head gakset torque specification for a 2011 and 2012 hyundai sonata 2.0 and 2.4L engine. Torque the head bolts in several passes. First torque to 23.9 to 26.8 foot pounds. Next, turn the bolts to 90 to 95 degree and again to 90 to 95 degree. Remember to use brand new head bolts and lubricate the new head bolts with fresh engine oil.
Where is the head gasket located in a car?
Regardless of the sequence, you will have to remove and separate most of the car parts near the top section of the engine. The head gasket sits beneath the cylinder head and above the engine block. Start replacing the head gasket when the engine is cold. Slide a clean drain pan under the radiator drain plug to allow the coolant to drain.