What is the code for anti lock brakes?

Anti-Lock Brakes (ABS) Codes C1214 Brake Control Relay Contact Circuit Open C1215 Brake Control Relay Contact Circuit Active C1216 Brake Control Relay Coil Circuit Open

What is the DTC code for Subaru ABS?

ABS (DIAGNOSTICS) 11.List of Diagnostic Trouble Code (DTC) ABS-23 ABS (DIAGNOSTICS) LIST OF DIAGNOSTIC TROUBLE CODE (DTC) 11.List of Diagnostic Trouble Code (DTC) A: LIST 1. WITHOUT SUBARU SELECT MONITOR

What are the ABS codes for a car?

Anti-Lock Brakes (ABS) Codes 1 C1214 2 C1215 3 C1216 4 C1217 5 C1218 6 C1221 7 C1222 8 C1223 9 C1224 10 C1225

What is the DTC code for abs-25?

ABS-25 ABS (DIAGNOSTICS) LIST OF DIAGNOSTIC TROUBLE CODE (DTC) 21 4A02 Open or short circuit in Front ABS wheel speed sensor RH cir-cuit Open or short circuit in Front ABS wheel speed sensor RH cir-cuit <Ref. to ABS-85, DTC 21 Ñ OPEN OR SHORT CIR-CUIT IN FRONT RIGHT ABS WHEEL SPEED SENSOR CIRCUIT Ñ , Diagnostics Procedure with Subaru Select

When to troubleshoot a GMC ABS brake system?

Instead, the ABS system will pump the brakes to provide better control over the vehicle for the driver. If you suspect you are having trouble with the GMC ABS brake system, you should troubleshoot the problem to verify whether there is a failure in the system. Open the fuse panel underneath the dash.

Why does my GMC ABS light keep coming on?

If the ABS dash light comes on and stays lit, and none of the ABS wires are damaged, it is likely that there is a partial failure in the ABS sensor. For specific information about GMC ABS braking systems, consult the particular vehicle’s manual (see Resources).

How to find the ABS code for the F150?

The last flash of the series is a long flash. Then it repeats over & over, until you turn the key off. Count all of the short flashes & the long one together (So 4 short & 1 long is code #5). If I remember right, it should be a number between 2 & 15 or so.

How to check for Bendix ABS fault codes?

Make sure trailer is stationary and wheels are properly chocked. Push the control knob to cycle the Brake Light Circuit for each desired Cycle in one second intervals. Count number of blinks on Trailer ABS Lamp, see chart below for specific fault info. faults detected.

Where can I find the ABS code on my Jeep?

Might not hurt to have a quick look at yours. The wheel speed sensors won’t throw an OBD code, so it won’t show up on a standard code reader. Go to AutoZone and ask for their loaner program code reader (NOT THE STORE READER). The loaner does ABS codes.

Can a Bosch 5.3 ABS lose its coding?

The loss of coding is normal on a Bosch 5.3 ABS/EDS/ASR/ESP -or- Bosch 5.7 (ESP also) vehicle when the slip ring / G85 sensor is disconnected. In this case you need to: 1) Build the Login specific to the equipment installed in the car and enter it.

Can a parking brake light be activated by ABS?

Usually, the brake fluid level sensor and the parking brake are the only two items that can activate the BRAKE light. But, not all vehicles are the same, and some of the earliest ABS systems would trigger both lights simultaneously for any ABS fault.

What is the fault code for Haldex ABS?

Haldex ABS Modal System Configuration Codes. In such circumstances the MODAL system may generate a fault code indicating slow wheel recovery group i.e. A fault code number such as, 41, 42, or 43. (see Fault Code List)

What does the ABS code c1214 and c1248 mean?

The system relay is commanded ON. The system voltage is less than 8?Volts for 0.23 seconds. The EBCM disables the DRP/ABS/TCS/VSES for the duration of the ignition cycle. The ABS indicator turns ON. The Traction Control indicator turns ON. The DIC displays the Service Stability System message. The EBCM will also set DTC?C1248.

What does the brake light on code c1214 mean?

The EBCM disables the DRP/ABS/TCS/VSES for the duration of the ignition cycle. The ABS indicator turns ON. The Traction Control indicator turns ON. The DIC displays the Service Stability System message. The EBCM will also set DTC?C1248. The red Brake warning indicator turns ON.

What does the brake light on ABS code mean?

The ABS indicator turns ON. The Traction Control indicator turns ON. The DIC displays the Service Stability System message. The EBCM will also set DTC?C1248. The red Brake warning indicator turns ON. The condition for the DTC is no longer present and the DTC is cleared with a scan tool.

Anti-Lock Brakes (ABS) Codes C1214 Brake Control Relay Contact Circuit Open C1215 Brake Control Relay Contact Circuit Active C1216 Brake Control Relay Coil Circuit Open

Navigation