What does OBD II fault code P1300 mean?
What Does Code P1300 Mean? OBD II fault code P1300 is a manufacturer specific code that is defined by carmaker Toyota, and Lexus in particular, as “Igniter Circuit Malfunction No.1”, or sometimes as “Igniter Circuit Malfunction (Bank 1), in cases where each bank of cylinders is fitted with a separate igniter.
When did they stop making the Saab 9-3?
In 2013-2014, an unsuccessful attempt was made to resume the production of 9-3 sedans, after which the company lost the rights to the Saab brand.
Where can I find the GM diagnostic trouble code?
Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s). Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions on all other GM diagnostic trouble codes. Manufacturer Specific Codes P1031HO2S Heater Current Monitor Control Circuit Sensors 1
What are the OBD2 codes for OBDII cars?
OBDII P Code Definitions. Be sure to double check the codes. Anything P1000 to P1999 or P3000 to P3400 will be Manufacturer specific and may not match the ones listed here. Check specific manufacturer pages on the site, as some of them, we list the OBD2 codes on those pages for those specific vehicles.
Where is the OBD plug on a Saab 9-5?
OBD connector location for Saab 9-5 (1997 – 2010) You will find below several pictures which will help you find your OBD connector in your car. The OBD2 plug is located under the steering wheel.
What are the different types of OBD2 error codes?
Heated oxygen sensor (H02S) 3, bank 1, heater control -circuit. high Intake air temperature (IAT) sensor 2 -circuit high input . Transmission Fluid Temperature Sensor Circuit Range/Performance
What are the error codes for the oxygen sensor?
Oxygen sensor signals swapped, bank 1 sensor 1/ bank 2 sensor 1 Oxygen sensor signals swapped, bank 1 sensor 2/ bank 2 sensor 2 Heated oxygen sensor (H02S) 3, bank 1, heater control -circuit malfunction Heated oxygen sensor (H02S) 3, bank 1, heater control -circuit low Heated oxygen sensor (H02S) 3, bank 1, heater control -circuit. high
How to find an OBD code for a car?
Trouble code scanner showed me three codes: ECM-P200A84 Inta… Car idling too fast at times and not at others… It’s Audi A4 1.8 2012 model.this car start then shutdown immediately. Stabilisation Control (ESC) Fault! See owner’s manual. i try to use OBD2 scan tool so there is the code found. ( P0642 )s… Check engine light came on.
What Does Code P1300 Mean? OBD II fault code P1300 is a manufacturer specific code that is defined by carmaker Toyota, and Lexus in particular, as “Igniter Circuit Malfunction No.1”, or sometimes as “Igniter Circuit Malfunction (Bank 1), in cases where each bank of cylinders is fitted with a separate igniter.
When is the P1300 Toyota engine code detected?
Most auto repairs shops charge between $75 and $150 per hour. When is the P1300 TOYOTA code detected? The P1300 code is for the ignition coil No.1 and is set when there is no IGF signal to the ECM during engine operation. Direct Ignition System (DIS) is a 1-cylinder ignition system that ignites one cylinder with one ignition coil.
What does P1300 stand for in igniter code?
NOTE #1: Code P1300 refers specifically to a malfunction in the igniter control/monitoring circuit, and NOT to a failure of or malfunction in any specific part or component within that circuit.
How much does it cost to repair a P1300 Toyota?
The cost of diagnosing the P1300 TOYOTA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
How much does it cost to diagnose P1300 Toyota code?
The cost of diagnosing the P1300 TOYOTA code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P1300 TOYOTA code detected?
When is the P1300 code detected in an ignition coil?
Most auto repair shops charge between $75 and $150 per hour. When is the code detected? The P1300 code is for the ignition coil No.1 and is set when there is no IGF signal to the ECM during engine operation.
What are the common causes of P1300 malfunctions?
Common causes of P1300 could include the following- Damaged, burnt, shorted, disconnected, and/or corroded wiring and connectors Defective ignition coils Defective igniter Defective PCM