What does OBD 2 fault code p1259 mean?
What Does Code P1259 Mean? OBD II fault code P1259 is a manufacturer specific code that is defined by carmaker Honda as “VTEC System Circuit Fault (Bank 1)”, and is set on these applications when the PCM (Powertrain Control Module) detects a defect, malfunction, or failure in the electrical control/monitoring system of the VTEC mechanism on Bank 1.
What causes a VTEC system error code p1259?
This error code can be caused by multiple of factors, such as: 1 Low oil pressure or low engine oil level 2 Defective VTEC solenoid 3 Open or shorted VTEC harness 4 Poor electrical connections in the VTEC circuit 5 Defective VTEC oil pressure switch More …
What are the possible causes of Honda p1259?
P1259 Honda Possible Causes. Low engine oil level or oil pressure. Faulty Variable Valve Timing and Lift Electronic Control (VTEC) solenoid. VTEC Solenoid harness is open or shorted. VTEC circuit poor electrical connection. Faulty VTEC oil pressure switch.
What causes a PCM signal error code p1259?
The most common cause of code P1259 is flat batteries in keys, with abnormal system voltages caused by faults and defects in the charging system that could damage control modules following close behind.
This error code can be caused by multiple of factors, such as: 1 Low oil pressure or low engine oil level 2 Defective VTEC solenoid 3 Open or shorted VTEC harness 4 Poor electrical connections in the VTEC circuit 5 Defective VTEC oil pressure switch More
What Does Code P1259 Mean? OBD II fault code P1259 is a manufacturer specific code that is defined by carmaker Honda as “VTEC System Circuit Fault (Bank 1)”, and is set on these applications when the PCM (Powertrain Control Module) detects a defect, malfunction, or failure in the electrical control/monitoring system of the VTEC mechanism on Bank 1.
P1259 Honda Possible Causes. Low engine oil level or oil pressure. Faulty Variable Valve Timing and Lift Electronic Control (VTEC) solenoid. VTEC Solenoid harness is open or shorted. VTEC circuit poor electrical connection. Faulty VTEC oil pressure switch.
The most common cause of code P1259 is flat batteries in keys, with abnormal system voltages caused by faults and defects in the charging system that could damage control modules following close behind.
What causes a Honda VTEC code p1259?
Nonetheless, some other common causes of code P1259 could include the following- Failed or failing PCM, but note that since this a rare event, the fault must be sought elsewhere before any control module is replaced
What causes a check engine light with a P0420 code?
In most cases, a P0420 code is caused by a bad catalytic converter. You will probably not have any symptoms except the check engine light with just the P0420 code stored. You may have other problems with your engine damaging the catalytic converter, which can cause symptoms like rough idle, rough acceleration, misfires, and hard shifting.
Where is the p1259 sensor located on a Honda Civic?
It should be noted though while that code P1259 specifically refers to a problem in the VTEC systems’ control/signal/monitoring circuit, some mechanical failure modes can contribute to this code being set and stored. Where is the P1259 sensor located? The image above shows the location of the VTEC oil control solenoid on a Honda Civic engine.
In most cases, a P0420 code is caused by a bad catalytic converter. You will probably not have any symptoms except the check engine light with just the P0420 code stored. You may have other problems with your engine damaging the catalytic converter, which can cause symptoms like rough idle, rough acceleration, misfires, and hard shifting.
It should be noted though while that code P1259 specifically refers to a problem in the VTEC systems’ control/signal/monitoring circuit, some mechanical failure modes can contribute to this code being set and stored. Where is the P1259 sensor located? The image above shows the location of the VTEC oil control solenoid on a Honda Civic engine.
What do you need to know about Honda p1259?
P1259 Honda Description. The PCM monitors oil pressure conditions in the hydraulic circuit of the VTEC mechanism according to the VTEC oil pressure switch downstream of the VTEC solenoid valve. If there is a disparity between oil pressure condition in the hydraulic circuit that is determined by the PCM command, and the oil pressure condition…
Where is the VTEC system malfunction code p1259?
Re: VTEC System Malfunction code P1259 has appeared. (… Check your variable valve timing oil pressure switch, it’s located on the passanger side just before the intake manifold, also the solenoid may be dirty or bad. some people say to clean the screen but that requires removing the entire assembly where these two units are… Good luck
What does p1259 stand for in immobilizer code?
There are no codes directly related to P1259. Any problem such as abnormal input or system voltages, intermittent faults, or high resistances in any part of the immobilizer control circuit will set code P1259. Below are some examples of definitions of code P1259 that do not relate to the anti-theft system.
When is the p1259 code detected in a powertrain?
When is the P1259 code detected? The Variable Valve Timing and Lift Electronic Control (VTEC) system activate the VTEC solenoid valve by the command from the Powertrain Control Module ( PCM ), and it charges/discharges the hydraulic circuit of the VTEC mechanism that is installed in the valve system to switch valve timing between Low and High.
P1259 Honda Description. The PCM monitors oil pressure conditions in the hydraulic circuit of the VTEC mechanism according to the VTEC oil pressure switch downstream of the VTEC solenoid valve. If there is a disparity between oil pressure condition in the hydraulic circuit that is determined by the PCM command, and the oil pressure condition…
Re: VTEC System Malfunction code P1259 has appeared. (… Check your variable valve timing oil pressure switch, it’s located on the passanger side just before the intake manifold, also the solenoid may be dirty or bad. some people say to clean the screen but that requires removing the entire assembly where these two units are… Good luck
How much does it cost to diagnose a p1259 code?
The cost to diagnose the P1259 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.