What does it mean when trouble code p0011 is set?
When trouble code P0011 is set, it means that the intake camshaft in Bank 1 is more advanced than the ECM has told it to be. What Are The Symptoms Of Code P0011?
What does the a stand for in a p0021 engine?
The “A” camshaft is either the intake, left, or front camshaft. A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1.
What are the symptoms of a p0021 DTC?
A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1. Most likely a P0021 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well.
What does the p0011 DTC on an Impala mean?
That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The “A” camshaft is either the intake, left, or front camshaft.
What do the p0011 and p0021 codes mean?
For the P0011 and P0021 codes to appear indicates that the OCV solenoid is mechanically open at all times and allowing engine oil to move the intake camshaft (s) without PCM intervention.
A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1. Most likely a P0021 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well.
What does DTC p0012 and p0022 mean?
DTC P0012 and P0022 indicate the timing is too retarded. When you consider what these codes are saying, it becomes obvious that these codes are more indicative of a mechanical failure or the results of poor maintenance. These four DTCs could be an electrically failed OCV but they would most likely be accompanied by a P0010 or P0020 code.
What to do if your check engine light says p0011?
Check to see if there are any other codes along with P0011 and clear your Check Engine Light with FIXD. Check the engine oil level and condition. If it’s low, adjust to spec and test drive to see if the concern is resolved. If it’s dirty, change the oil and filter and test drive to see if the concern is resolved.
What are the causes of a P0300 leak?
P0300 Causes 1 Faulty or worn spark plugs * 2 Faulty spark plug wires or coils * 3 Distributor failure * 4 Faulty fuel injector 5 Vacuum leak 6 Low fuel pressure 7 Camshaft sensor defective 8 Crankshaft sensor defective 9 Engine timing off 10 Leaking head gasket
What does the P0300 code on a spark plug mean?
The P0300 code means that a cylinder(s) is misfiring or is randomly misfiring. Start by checking for intake leaks, intake gaskets are common caused of multi-cylinder misfiring. If no leak are found the next step is to replace the spark plugs.
Check to see if there are any other codes along with P0011 and clear your Check Engine Light with FIXD. Check the engine oil level and condition. If it’s low, adjust to spec and test drive to see if the concern is resolved. If it’s dirty, change the oil and filter and test drive to see if the concern is resolved.
What does trouble code p0021 in Bank 2 mean?
The camshaft (s) is (are) adjusted by the ECM through the use of an oil control valve (s) (OCV) also called variable valve timing control solenoid valves. When trouble code P0021 is set, it means that the intake camshaft in Bank 2 is more advanced than the ECM has told it to be.
What does it mean when trouble code p0138 is set?
When trouble code P0138 is set, this indicates that there is a high voltage (steadily above .9 volts) for more than 10 seconds indicating a lack of oxygen in the exhaust stream and an abundance of fuel at sensor 2 on the bank 1 of the engine.
When did p0013 come up on my car?
I had P0013 (Exhaust Camshaft Position Actuator Solenoid Control Circuit) come up after finishing a 5 hour drive about a year ago. Basically I cleared the code, drove back to Toronto with no problems. Code hasnt come back and I’ve put about 10,000km more on it.
How to fix engine code p0010 on 2.4L?
Just remove the hold-down bolts & pull up on the actuators. Put engine oil on the new o-rings & don’t over-torque the hold-down bolts (torque spec is only 7 ft-lbs). The actuators are keyed differently (& have different part numbers) so you can’t interchange them.
The camshaft (s) is (are) adjusted by the ECM through the use of an oil control valve (s) (OCV) also called variable valve timing control solenoid valves. When trouble code P0021 is set, it means that the intake camshaft in Bank 2 is more advanced than the ECM has told it to be.
Where are the OBD and OBD2 codes stored?
The Electronic Control Unit (ECU) monitors several engine sensors and actuators. If a problem occurs the information is stored in the ECU’s memory for retrieval. The codes are displayed by the red diode on the ECU. The codes are interpreted by the number of times and duration the diode flashes.
When trouble code P0011 is set, it means that the intake camshaft in Bank 1 is more advanced than the ECM has told it to be. What Are The Symptoms Of Code P0011?
What does it mean when code p0014 is set?
The camshaft (s) is (are) adjusted by the ECM through the use of an oil control valve (s) (OCV) also called variable valve timing control solenoid valves. When trouble code P0014 is set, it means that the exhaust camshaft in Bank 1 is more advanced than the ECM has told it to be. What Are The Symptoms Of Code P0014? What Is The Cause Of Code P0014?
What causes a p0010 code on an engine?
P0010 Possible Causes. Dirty Oil. Low engine oil level. Faulty Intake Camshaft Position Actuator Solenoid. Intake Camshaft Position Actuator Solenoid harness is open or shorted. Intake Camshaft Position Actuator Solenoid circuit poor electrical connection.
When do I get a p0010 error on bank 1?
When the Engine Control Module tries to adjust the timing of the Bank 1 intake camshaft with one of these oil control valves, and it alerts an electrical issue with the solenoid windings in the valve or the circuit that goes into the valve, the code P0010 error is triggered.
What does DTC code p0010 stand for?
DTC P0010, P0016, P0335, P0336, P0340, or P0341 are not set. The system voltage is between 11-18 volts. The engine is running. The engine control module (ECM) has enabled the CMP actuator and commanded greater than 0 degrees. DTC P0011 runs continuously when the above conditions are met.
How much does it cost to diagnose a p0010 code?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P0010 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.