What does a p1326 code on a Kia mean?

P1326 is a knock sensor code. It’s designed to set when the engine is experiencing crank shaft damage due to oil starvation. These engines had issues where they would wear out prematurely so Kia programmed in a “limp mode” which wouldn’t let the vehicle go above 20 mph if the knock sensor detected that the crank was being damaged.

What does p1326 mean on a fuel pump?

No one seems to know what code P1326 is per say so where we go from here you think its a fuel pump problem or what ??? P1326 is a knock sensor code. It’s designed to set when the engine is experiencing crank shaft damage due to oil starvation.

What does the code p0014 on a check engine mean?

The check engine light is on and you’ve checked the code with an OBD-II scanner. The result was P0014. What now? What does the code P0014 mean? How do you fix it? What Does the Code P0014 Mean? P0014 is a diagnostic trouble code related to the variable timing of valves in the engine.

How much does it cost to diagnose p1326 Hyundai engine light?

The cost of diagnosing the P1326 HYUNDAI code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

Is there a p1326 fault code on my car?

The engine lost some power (struggled to accelerate) and I noticed it shuddered once during acceleration. Car was being driven in cold (~20 degrees) conditions. I used an OBDII scanner and saw that there is a pending P1326 fault code (no other codes).

How much does it cost to repair a Kia p1326?

The cost of diagnosing the P1326 KIA code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. The Knock Sensor Detection System (KSDS) detects vibrations indicating the onset of excessive connecting rod bearing wear.

What should I do if I have a p0011 code?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.

What are the trouble codes for Kia cars?

Kia Codes; Trouble Code Fault Location Probable Cause; P1000 – P1099 (Fuel and air metering and auxiliary emission control) P1000: System diagnosis incomplete: Drive cycle incomplete, ECM: P1100 – P1199 (Fuel and air metering) P1100: Manifold absolute pressure (MAP) sensor- for EGR system – circuit malfunction: Wiring, MAP sensor: P1102

How much does it cost to repair a Kia p0136?

The cost of diagnosing the P0136 KIA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

How much does it cost to fix a Kia p0136 code?

The cost of diagnosing the P0136 KIA code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0136 KIA code detected? It takes more time for the sensor to respond between rich and lean than the specified time.

What happens when you disconnect the battery on a Kia?

Disconnecting the battery on your Kia sometimes deprograms the keyless entry remote, the vehicle alarm and the internal computer in the vehicle. To reset each of these functions after reconnecting your Kia’s battery, you need to reprogram your keyless entry remote control, which will reset the rest of the vehicle.

Why was p1326 added to the PCM?

Fault P1326 was added the the PCM via a software update to detect engine bearing failure using the knock sensor. The system is flawed, electrical interference in the wiring can cause false alarms. An overlay wiring harness has been developed to correct the false alarms.

What does DTC code p1326 mean on Hyundai?

At that time, Diagnostic Trouble Code (DTC) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM.

What are the possible causes of a p1326 Kia?

P1326 KIA Possible Causes 1 Faulty Knock Sensor 2 Knock Sensor harness is open or shorted 3 Knock Sensor circuit poor electrical connection 4 Engine mechanical problem 5 Reprogram Engine Control Module (ECM)

How much does it cost to repair a p1326 Hyundai?

The cost of diagnosing the P1326 HYUNDAI code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. The Knock Sensor Detection System (KSDS) detects vibrations indicating the onset of excessive connecting rod bearing wear.

How much does it cost to diagnose a p1326 code?

The cost of diagnosing the P1326 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

The cost of diagnosing the P1326 HYUNDAI code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What kind of engine does a 2011 Kia Sportage have?

2011 Kia Sportage Engine TSB Details … 2011 Kia Sportage Engine and Engine Cooling TSB Details … 2011 Kia Sportage Equipment TSB Details … 2011 Kia Sportage Owner Manual and Service Manual TSB Details … 2012 Kia Optima Electrical System TSB Details …

What does the knock sensor on a Kia mean?

P1326 KIA Meaning The Knock Sensor Detection System (KSDS) detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure.

Where is the trouble code for limp mode?

Because of this, every time when the limp mode is active, there will be a stored trouble code in the trouble code memory. Therefore, the best solution to fix the limp mode without replacing the wrong parts is to find out which this trouble code is.

Why does my engine go into limp mode?

The reason for this is that limp mode could be caused by a lot of different engine components in your engine bay. Therefore, the solution for this is to read the trouble code memory with an OBD2 scanner to find the problem before you are replacing any engine parts! Here is a list of different possible causes of limp-mode.

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1326 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

What is the p1326 code on a Hyundai Santa Fe Sport?

15 people found this helpful. 1/29/2020 – P1326 code on 2015 Santa Fe Sport with 66,000 miles on it. We have owned it 3 months. Check engine light flashing. Won’t accelerate over 60mph and hesitates when you push on the gas quickly.

Navigation