What do I need to replace my water pump?
The drive belt or timing belt must also be removed, along with any other parts that obstruct access and the gasket that is affixed between the water pump gasket that is placed between the engine and water pump.
How long does it take to do a water pump at Mitchells?
Mitchell’s says 7.5 hours. Preparing correctly, it can be done in 4 hours. Dealer quote will most likely land in the $1100 parts and labor. Read all of the responses on the DIY ^^^^^.
How long does it take to install a water pump?
Alldata says 5.9 hours. Mitchell’s says 7.5 hours. Preparing correctly, it can be done in 4 hours. Dealer quote will most likely land in the $1100 parts and labor. Read all of the responses on the DIY ^^^^^. I’ve had them done at independent shops for $700 OTD.
The bolts are torqued in sequence using a calibrated inch pound torque wrench. For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner.
What to do with a 3.5L water pump?
Discard the nuts and the gasket. Remove the LH and RH catalytic converters. Refer to the Exhaust Manifold procedure for more information on catalytic converter removal. If equipped, remove the heat shield and disconnect the block heater electrical connector.
What do you need for real time labor guide?
While the labor guide and customer management from Real-Time Pro are great you need more advanced shop management software. You need features like accounts receivable, technician tracking, automatic parts markup, inventory, etc. You need Automotive Expert! Automotive Expert – Free Trial!
The bolts are torqued in sequence using a calibrated inch pound torque wrench. For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner.
What should I do when my Honda Accord water pump is replaced?
Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement. The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime. Real customer reviews from Honda owners like you.
How do you replace a water pump on an Audi A3?
A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench. For applications where the water pump is driven by the timing belt, the timing belt must be removed.
What happens to the water pump on a cold engine?
On a cold engine, the engine coolant is drained to a level below the water pump. Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump. The bolts holding the pump to the engine are removed and the pump is pulled out.
How long does it take to replace a Mazda water pump?
Just to replace the water pump the job involves removal of the timing chain, guides and cover, a job that can take 12 to 14 hours to complete. The plaintiffs claim Mazda tells technicians to remove the oil pan drain plug and line the cylinder block with plastic sheeting to prevent coolant from penetrating or accumulating in the oil pan.
How do you change the water pump on a Miata?
To replace the water pump, start with the Timing Belt instructions . Once you get to the point where it tells you to “change the water pump”, come back here. We’re not sure if it has to come off, but the job is a bit easier if you remove the cover plate marked with the E/I positions for the timing marks.
How do you replace a water pump on a Chevy Cruze?
The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench. For applications where the water pump is driven by the timing belt, the timing belt must be removed.
What kind of water pump does Mazda CX-9 have?
The Mazda CX-9 and Mazda6 vehicles are equipped with MZI Cyclone engines introduced by Mazda in 2007. According to the lawsuit, the Cyclone engine has an internal chain-driven water pump which means the timing chain is connected to the water pump and provides the power the water pump needs to circulate coolant through the engine.