What are the causes of a p1682 GMC ignition?

What are the causes of a p1682 GMC ignition?

P1682 GMC Possible Causes 1 Faulty ignition switch 2 Ignition Switch harness is open or shorted 3 Ignition Switch circuit poor electrical connection 4 Faulty Engine Control Module (ECM)

How much does it cost to diagnose a p1682 GMC code?

The cost of diagnosing the P1682 GMC code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P1682 GMC code detected? Engine Light ON (or Service Engine Soon Warning Light)

What does DTC p1682 stand for in ECM?

The second ignition 1 voltage circuit is supplied by the run/crank relay through a fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the 2 ignition 1 voltage circuits, DTC P1682 will set.

P1682 GMC Possible Causes 1 Faulty ignition switch 2 Ignition Switch harness is open or shorted 3 Ignition Switch circuit poor electrical connection 4 Faulty Engine Control Module (ECM)

The cost of diagnosing the P1682 GMC code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P1682 GMC code detected? Engine Light ON (or Service Engine Soon Warning Light)

The second ignition 1 voltage circuit is supplied by the run/crank relay through a fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the 2 ignition 1 voltage circuits, DTC P1682 will set.

Where does the second ignition switch go on a GMC Sierra?

The first one goes to the ECM through the throttle actuator control. The second ignition voltage circuit (the one in question) goes through the ignition switch. With P1682 you’ll experience a no start or intermittent start condition.

Are there any problems with the GMC Yukon?

GMC Yukon owners have reported 15 problems related to car will not start (under the electrical system category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of GMC Yukon based on all problems reported for the Yukon.

How much does it cost to diagnose p1682 GMC code?

The cost of diagnosing the P1682 GMC code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P1682 GMC code detected?

Why does my GMC Yukon Car not start?

While driving the vehicle, heard a clicking/cracking/popping noise, smelled a strong odor of smoke and burning smell from the front passenger side underneath the glove box area. At the same time the widows, mirror, and electric locks on the passenger side of the vehicle would not operate.

When is the code detected for DTC p1682?

The second ignition 1 voltage circuit is supplied by the run/crank relay through a fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the 2 ignition 1 voltage circuits, DTC P1682 will set. When is the code detected?

What does p0700 mean on a GMC ignition?

The P1682 it is not related on how the transmission shifts. The P0700 is an information code and just means that there is a problem with the transmission. You should focus more on the P0716 code. The most common problem for the P0716 code is the Transmission Input Shaft Speed Sensor and/or the transmission filter.

What does p1682 mean on a GM ignition switch?

P1682 GM: Ignition 1 Switch → Circuit 2 January 9, 2020 by Jason P1682 is a diagnostic trouble code that indicates that the ignition switch is having a voltage problem. It is typically caused by a faulty ignition switch.

The cost of diagnosing the P1682 GMC code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P1682 GMC code detected?

The P1682 it is not related on how the transmission shifts. The P0700 is an information code and just means that there is a problem with the transmission. You should focus more on the P0716 code. The most common problem for the P0716 code is the Transmission Input Shaft Speed Sensor and/or the transmission filter.