How to troubleshoot a Mercedes Benz transmission problem?
To properly troubleshoot the transmission problem on your Mercedes-Benz, you will need a diagnostic scanner that can retrieve the fault codes from the transmission control unit (TCU). The next step is to get a hold of such an advanced diagnostic scanner, read the TCU error codes which will help you narrow down the problem with your Mercedes-Benz.
Can you read the fault code on a Mercedes Benz?
Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS
What does it mean when your transmission says p0720?
You are experiencing transmission problems. You press the gas pedal, and the engine RPMs go up to 4000 or even higher and you are limited to a max speed of about 30 MPH. The check engine light (CEL) comes on. You scan the car using an OBD-II code reader, and you get fault codes such as P0715, P0720, P0700.
What is the error code for a Mercedes 5 speed transmission?
Here is a list of Mercedes 5-speed and 7-speed automatic transmission related error codes. P0700 – Transmission Control System Malfunction (Generic Code telling you there is a gearbox problem) P 0716 P0717 P0718 – Input / Turbine Speed Sensor Circuit Malfunction / Range Performance / No Signal / Intermittent
What kind of transmission problem does Mercedes C350 have?
The contact owns a 2009 mercedes c350. The contact stated that when the accelerator pedal was engaged, the transmission surged forward at a high rate. The failure occurred intermittently. The dealer was unable to duplicate or diagnose the failure. The failure mileage was 15 and the current mileage was 32000.
Are there any problems with the Mercedes C class?
Other Common Power Train related problems of Mercedes Benz C Class Problem Category Number of Problems Automatic Transmission problems 7 Power Train problems 3 Driveshaft problems 1 Automatic Transmission Torque Converter 1
What is the problem with the Mercedes C240 transmission?
P240C The CAN signal for the selector lever position from component N15/5 (electronic selector lever module control module) is implausible. P2067 Component N15/3 (ETC control module) memory is fault.
What happens when a Mercedes Benz goes into limp mode?
When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level. The transmission has a dipstick tube but with no dipstick in it.
What is the fault code on a Mercedes?
You press the gas pedal, and the engine RPMs go up to 4000 or even higher and you are limited to a max speed of about 30 MPH. The check engine light (CEL) comes on. You scan the car using an OBD-II code reader, and you get fault codes such as P0715, P0720, P0700.
What causes oil leak in Mercedes Benz transmission?
The first thing that you should check is the 13-pin connector plug. This is the electrical wire harness that plugs into the valve body which is inside the transmission. It leaks oil and causes communication problems between the transmission control unit and the sensors on the valve body.
To properly troubleshoot the transmission problem on your Mercedes-Benz, you will need a diagnostic scanner that can retrieve the fault codes from the transmission control unit (TCU). The next step is to get a hold of such an advanced diagnostic scanner, read the TCU error codes which will help you narrow down the problem with your Mercedes-Benz.
What causes a Mercedes P2004 code to break?
Mercedes P2004 Cause. Weak material used in construction of the intake manifold air lever is the main common cause of Mercedes P2004 codes. If you have a broken manifold air lever you may want to consider replacing your old lever with a high strength aluminum design.
What causes a Mercedes Benz to not start?
In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems
You press the gas pedal, and the engine RPMs go up to 4000 or even higher and you are limited to a max speed of about 30 MPH. The check engine light (CEL) comes on. You scan the car using an OBD-II code reader, and you get fault codes such as P0715, P0720, P0700.