How to replace the ignition switch on a 1989 Jeep?
How to Replace the Ignition Switch in a 1989 Jeep. Insert the ignition key into the cylinder lock and turn it to the “Start” position. Locate the cylinder lock pin on the side of the switch and press the pin in with a flat-head screwdriver. Pull the lock cylinder out of the switch about 1/2 an inch.
How do you install a replacement ignition switch?
Position your replacement ignition switch at the edge of your steering column so it is prepared to install. Change the switch’s slider so that it is set on “Accessory.”. Attach the slider hole and actuating rod. Connect the switch.
What to do if your ignition switch is broken?
If the lock cylinder is broken (as illustrated) make sure you locate and remove the broken piece from inside the switch to avoid an electrical short. If you cannot accomplish this repair on the car, continue with these instructions to remove the switch assembly with the lock from the column.
Where is the release pin on an ignition switch?
The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.
How do you change ignition switch on Jeep Cherokee?
Position your replacement ignition switch at the edge of your steering column so it is prepared to install. Change the switch’s slider so that it is set on “Accessory.” Attach the slider hole and actuating rod. Connect the switch. Use your fingers to get the pair of retaining screws tight but not stuck.
Position your replacement ignition switch at the edge of your steering column so it is prepared to install. Change the switch’s slider so that it is set on “Accessory.”. Attach the slider hole and actuating rod. Connect the switch.
What happens if your ignition switch malfunctions?
If the switch ever begins to malfunction, you could end up stuck somewhere with the car stalled. You might not even be able to start it. You will get the first hint that this problem has arisen when you have difficulty starting the vehicle, perhaps having to retry a couple times.
How do you get the ignition key out of a jeep?
Access the solenoid: Lift the rubber mat off the tray and remove the two tray screws. You will see the solenoid. It’s a white cylinder with a metal bar protruding rearward toward the shifter. You might opt to remove the center console too. Quick Fix: If you’re in a jam and need to remove the key without disassembling things read on.
Why is the ignition key stuck in my Grand Cherokee?
Brilliant post, Milo, very useful. I have a 2003 Grand Cherokee Overland 2.7 CRD, which I love, and earlier today the ignition key would not come out of the ignition. My first thought was the ignition lock itself, so I spent some time jiggling the key in the lock without success.
How to remove the ignition switch without a key?
How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.
Can you replace the ignition switch on a 1998 Jeep Wrangler?
Replacing the ignition switch on a 1998 Jeep Wrangler entails removing the ignition switch tumbler, as well. A point many times confused is the separation of the two related parts. The key, also called the tumbler, has no electrical function; its function is strictly related to vehicle security.
What to do if your ignition key goes bad on a Jeep Wrangler?
If you have a key that’s in better shape, you’d want to use that one to make a duplicate. If you have no key to duplicate, many manufacturers can use the VIN number to cut you a brand new OEM key. Just be prepared to prove ownership to Jeep in some way. The Wrangler’s ignition lock cylinder itself can go bad over time.
What to do when your key is stuck in the ignition?
Give the wheel a wiggle while lightly trying to turn the key out of the ignition. If the steering lock is causing a bind, this will relieve the pressure and get the key out.
Where are the Torx screws on a jeep?
Allow 15 minutes for the circuits to rid themselves of any residual voltage before continuing. Tilt the steering column all the way up and remove the three Number 20 Torx screws located at the bottom of the steering column cover — two of them hold the cover together and the third holds the cover to the column.