How to replace the brake light switch on a Mercedes Benz ML Class?
How to remove and replace the stop / brake light switch on Mercedes Benz ML Class. Step by step instructions on how to replace the brake light switch on a ML320, ML430, ML500 W163. Remove the panel under the dashboard. Unplus the OBD II cable from the port if neccessary. This will give you more room but is not neccessary.
What do I need to change the brake light switch?
Checking the brake light operation is not a good test.) ESP, BAS, ABS lights turn on. Car won’t shift properly. Stuck in gear. To change the brake light switch on your Mercedes-Benz you will need a star torx bit set. You can buy a set on Amazon for under $20. One of our favorite sets is the Neiko 10071A 13-Piece Torx Bit Cr-V T-Socket Set.
Where is the brake light stop switch located?
Locate brake light stop switch The brake light switch is located right above the brake pedal. To access it, remove the underside panel cover. Usually, the panel is held in place with 3 to 5 screws.
Where is the brake light switch on a medic?
Unplus the OBD II cable from the port if neccessary. This will give you more room but is not neccessary. Unplug the electrical connector from the brake light swtich. The brake light switch is located right above the brake pedal. Remove the brake light switch by pressing on the lock tab and rotating.
Are there brake light switch problems in Mercedes?
This is a common problem on Mercedes-Benz models E-Class, C-Class, S-Class, CLS-Class, ML-Class, CLK-Class and other. Too many to list here but the most frequently defective brake light switch problems are seen with E 320 C 240 CLK 500 ML 320 ML 350 S 430 to name a few.
How do you remove a brake light switch?
To remove a newer style of switch, you have to rotate it in the counterclockwise direction and remove it from the socket. You will not need to use too much force to do this. Step 4b: Remove an older style switch. With the older style of switches, you will need to use a wrench to remove one of the nuts.
What to do if your brake light does not work?
Press down on the brake pedal and see if the lights illuminate. Note: On the newer style switch, you will not need to adjust anything and the lights should work after installation. If the lights do not work even after adjustment, a certified technician would be able to inspect the switch and diagnose the problem.
What is the part number for the brake light switch?
Here are some part numbers related to the brake light switch. 001 545 95 09 05, 001 545 9509, 0015459509 This part will fit models.
Why is my brake light not working on my Mercedes?
Yes it could be the brake light switch. It could be other problems such as low brake fluid level or failed ABS wheel speed sensor. There is no certain way to know without first doing some troubleshooting. Where is the brake light swtich located on a Mercedes-Benz? Right above the brake pedal.
Checking the brake light operation is not a good test.) ESP, BAS, ABS lights turn on. Car won’t shift properly. Stuck in gear. To change the brake light switch on your Mercedes-Benz you will need a star torx bit set. You can buy a set on Amazon for under $20. One of our favorite sets is the Neiko 10071A 13-Piece Torx Bit Cr-V T-Socket Set.
Locate brake light stop switch The brake light switch is located right above the brake pedal. To access it, remove the underside panel cover. Usually, the panel is held in place with 3 to 5 screws.
Can a defective brake light switch cause an accident?
Learn how easy it is to change the brake light switch on your Mercedes Benz. Brake light switch issues with Mercedes-Benz cars are the #1 problem that most owners face. Defective brake light switch can cause the lights not to turn on, therefore causing accidents and possibly get you in a middle of a lawsuit you could have avoided.
Where is the light switch on a Mercedes Benz?
You will need to open the driver side door to give you access to the T20 screw located under the parking brake handle as well as remove the access panel on the end of the dash. Begin by pulling the brake handle out. This will give you access to a single T20 Torx screw located under the handle.
How long does it take to change a brake light switch?
Changing the brake light switch is easy. Follow the directions on this page and you can replace the brake light switch in less than 20 min. How much does a Mercedes-Benz brake light switch cost? You can find a replacement brake light switch for very little.
How do you replace the brake light switch on a ML320?
Step by step instructions on how to replace the brake light switch on a ML320, ML430, ML500 W163. Remove the panel under the dashboard. Unplus the OBD II cable from the port if neccessary. Unplug the electrical connector from the brake light swtich. Remove the brake light switch by pressing on the lock tab and rotating.
Where is the brake light switch on a Mercedes Benz?
The brake light switch is located right above the brake pedal. To access it, remove the underside panel cover. Usually, the panel is held in place with 3 to 5 screws. Mercedes-Benz uses Torx head screws.
How much does it cost to replace a brake light switch?
You can find a replacement brake light switch for very little. Click on the Amazon link to find some of the best prices on Mercedes-Benz Brake Stop Light Switches. How much does it cost to change the stop light switch? At a mechanic repair shop it can cost between $120-$250. If you do it yourself, it can cost less than $20.
Are there any brake light switches that are defective?
This is a common problem on Mercedes-Benz models E-Class, C-Class, S-Class, CLS-Class, ML-Class, CLK-Class and other. Too many to list here but the most frequently defective brake light switch problems are seen with E 320 C 240 CLK 500 ML 320 ML 350 S 430 to name a few. Starting back in 1996 model years all the way up to the current models.
How do I replace the brake light switch?
Remove the brake light switch by pressing on the lock tab and rotating. Install the new brake light switch in revers order. Plug the electrical connector back in and install the under dash panel. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.
Where is the brake light switch on a Mercedes W210?
In the older W210 E-Class, it is located in the back on the back of the pedal. You may need to lay on your back to access the switch. To remove the switch, press on the locking tab and then rotate it clockwise. Step 4. Install new switch Once you remove the old brake light switch, unplug the electrical wires from it.
How do you change the brake light switch on a Mercedes?
Once you remove the old brake light switch, unplug the electrical wires from it. Plug the wires in the new switch and install the new switch by twisting it counter-clockwise. Watch the following video on how to install brake stop light switch on an Mercedes-Benz E-Class . I replaced the brake light switch but the lights are still on.
Is there a problem with the brake light switch?
Too many to list here but the most frequently defective brake light switch problems are seen with E 320 C 240 CLK 500 ML 320 ML 350 S 430 to name a few. Starting back in 1996 model years all the way up to the current models. Can’t get car out of park, is it the brake light switch?