How to repair front wheel on Kia Sportage?

1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire (A) from front hub. Be careful not to damage to the hub bolts when removing the front wheel and tire (A). 3. Remove the brake caliper mounting bolts, and then hold the brake caliper assembly (B) with wire. 4.

Can you replace lug studs on Kia Forte?

3 of my lug bolts snapped in half, long story, took off wheel, to see there wasn’t enough clearance to replace the bolts so I’m trying to take the hub off. I got the big nut in the middle off, removed caliper and brake rotor and still don’t see how I can get the hub off.

How do you replace studs on Honda Odyssey?

If it is like the Hondas, the only way to get to the bolts is to remove the hub/bearing. Probably need to remove the knuckle and hammer out the bearing/hub. I tried unsuccessfully with a slide hammer on the Honda Odyssey.

How do you replace a lower ball joint on a Kia?

Park the vehicle and place it in (P) park. Set the parking brakes. Jack up your vehicle and place jack stands under the car. Next, remove the front wheel. Remove ball joint bolts. Remove the bolts that hold the lower ball joint in place. Remove the bolt by the knuckle. This will allow you to lower the ball joint. Remove the old ball joint.

How to adjust the camber on a Kia Sportage?

Adjust the camber by turning the cambolt of the rear lower arm. Hub nut tightening sequence Tighten the hub nuts as follows. Tightening torque : 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft) When using an impact gun, fi

What do I need to replace CV axle on Kia?

If no powered impact tool is available, brace the wheel hub from moving by taking a long and strong metal bar (such as a crowbar) and bracing the bar on the ground and on two wheel hub lugs. Either a breaker bar or cheater bar will be needed to generate enough torque to remove the axle nut.

How do you replace a brake line on a Kia?

Remove the brake line clip that holds the brake line to the suspension strut. A pair of pliers can help pull the clip off. Remove the two nuts that hold the brake caliper assembly to the steering knuckle. Pull the caliper away from the brake rotor. Support the caliper so that the brake line is not stretched and potentially damaged.

How do you replace a CV axle on a Kia Sportage?

This video and discussion show you how to remove and replace the right (passenger side) CV axle on a Kia Sportage. A nylon strap or rope can be used to “snap out” the axle from the transmission. This repair can also be performed on a Hyundai Tuscon (2005-2007).

How to replace the CV axle on a Kia Tuscon?

A nylon strap or rope can be used to “snap out” the axle from the transmission. This repair can also be performed on a Hyundai Tuscon (2005-2007). This five-minute video will provide you with visual step-by-step help for completing the removal and replacement of Kia Sportage passenger side CV axle.

How do you remove a front drive support bearing?

The front driveshaft is going to be attached solid inside the output shaft supports. In order to remove the driveshaft, you’ll need a rubber or plastic tipped hammer. On the front of the driveshaft is a welding mark that is solid and is the best place to hit with the hammer to loosen the driveshaft.

How is a center support bearing attached to a rear wheel drive car?

On some rear wheel drive vehicles, the bearing block bolts thread into nuts that are solidly mounted or welded onto the frame. On some vehicles, two part nuts and bolts are used to attach the rear of the front driveshaft to the center support bearing.

What happens when a center support bearing fails?

Another warning indicator is when you feel a shudder on the floor board, the accelerator pedal or the brake pedal as you accelerate or brake. A failed bearing is unable to support the driveshaft, and as a result the driveshaft will flex, causing a vibration and shuttering sensation that can be felt throughout the vehicle when it’s broken.

What kind of side step rails do Kia Sportage use?

At AutoAnything, we stock only the best products, produced by industry leaders like Westin, Lund, Aries and BAK. Each set of Sportage side steps is custom-tailored to your make, model and year for the perfect fit and to provide an easy, no-drill install that attaches directly to the pre-existing mounting slots already on your vehicle.

How to remove and replace a front wheel bearing?

How to remove and replace a front wheel bearing without a press. All stages of removal and refitting step by step : hub removing, wheel bearing extraction, bearing refit, hub refit. Front hub carrier bearing replacement

What kind of running board does Kia Sportage use?

Consider Kia Sportage nerf bars & running boards from AutoAnything. They add comfort, convenience and safety to the side of your vehicle by providing an all-weather tread on either the 3″ metal tubing of a nerf bar or the more refined elegance of a running board.

Are there round step nerf bars for Kia Sportage?

Check out this recent Kia Sportage Steelcraft 3″ Round Step Nerf Bars customer review: ,Bernard , from Lumberton, TX says “The overall look was a feeling of how amazing that looks on my vehicle. the bars give my vehicle a look of its own.the installtion was easy and the finish was excellent.I would highly tell anyone to add them.”

How do you remove a CV axle from a Kia?

Wiggle the knuckle off, or place a pry bar between the strut and the knuckle until they are separated. Push or tap the CV axle shaft through the wheel hub until the two are separated. III. Removing the CV Axle From the Transmission Remove the splash guard that covers the crank shaft and harmonic balancer.

How do you remove the CV axle nut?

Remove the CV axle nut cotter pin. Using a 32-mm socket attached to a powered impact driver, torque the CV axle nut off of the CV axle. If no powered impact tool is available, brace the wheel hub from moving by taking a long and strong metal bar (such as a crowbar) and bracing the bar on the ground and on two wheel hub lugs.

How to repair front knuckle on Kia Sportage?

Remove the front lower arm from the front knuckle using the SST (0K545-A9100). After removing bolts from the front knuckle, install and tighten the sub body bolt (A) . Input the sub body (A) between the front knuckle and the sub body bolt. Tighten bolt (B) of the sub body bolt to broaden the gap of the front knuckle. Install the safe wire (A).

What are the best front brake pads for Kia Sportage?

A few compatible replacement sets of new front brake pads with their part numbers include the following: Power Stop Z23-1847, Raybestos MGD1847CH, Bendix CFC1847 , Maxim PC1847 and Wagner QC1847.

Where is the wear indicator on Kia Sportage?

On this 2018 Sportage, the wear indicator bar was situated at the top of the old inner pad. If your new set of front brake pads includes a bag of replacement hardware, pull the old metal pad abutment or “anti-rattle” clips out of the top and bottom of the bracket.

Navigation