How to repair a Hyundai Santa Fe rear hub carrier?
Repair procedures Hyundai Santa Fe DM 2013-2018 Service Manual / Driveshaft and axle / Rear Axle Assembly / Rear Hub – Carrier. Repair procedures 1. Remove the front wheel and tire (A) from front hub. Be careful not to damage to the hub bolts when removing the front wheel and tire (A). 2. Remove the rear brake caliper. 3.
Is it necessary to replace wheel bearings on a Hyundai?
When it comes to the nuts and bolts of bearing replacement, Hyundais offer no special challenges and an experienced tech should have no problem handling the job. As always, it never hurts to go over the basics. We’ll take a look at the recommended procedure as outlined on the Hyundai service information website, www.hmaservice.com.
When to remove the hub from a wheel bearing?
It’s easier to clean up the threads on a tie rod end before it’s removed from its taper, than it is later; a couple of extra minutes during disassembly can pay dividends on the other end. With the bearing carrier on the bench, the first step is to remove the hub from the bearing.
How do you remove wheel bearing from bench?
With the bearing carrier on the bench, the first step is to remove the hub from the bearing. Whether you use a press or hub tool to accomplish this step, you’ll likely end up with the outer inner bearing race on the hub. A.
How much does it cost to replace wheel bearings on a Hyundai Santa Fe?
Hyundai Santa Fe Wheel Bearings Replacement at your home or office. Hyundai Santa Fe Wheel Bearings Replacement costs $273 on average. Following is a breakdown of the labor and parts estimates. What are wheel bearings and how do they work?
How to replace a rear wheel bearing on a 2001 Hyundai?
An error occurred. Please try again later. (Playback ID: 1LKyv0ghz1WsZrEj) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.
When do you replace wheel bearings on a car?
The complexity of wheel bearing replacement varies greatly depending on the vehicle make, model, year, the wheel position (front versus rear), and the drive type (AWD versus FWD): On vehicles with unitized wheel bearing/hub assemblies, the brake rotor and caliper are removed.
How do you change wheel bearings on a Toyota Tundra?
On vehicles where the wheel bearing is pressed into a cavity within the steering knuckle, the steering knuckle must be removed from the vehicle in order to press out the old bearing and press in the new bearing. On some vehicles, the wheel bearing is pressed onto an axle shaft and thus the axle must be extracted from the axle carrier.
How to repair a Santa Fe rear driveshaft?
Plug the hole of the transaxle case with the oil seal cap to prevent contamination. Support the driveshaft properly. Replace the retainer ring whenever the driveshaft is removed from the transaxle case. 10. Install in the reverse order of removal. 11. Check the rear alignment. 1. Check the driveshaft boots for damage and deterioration. 2.
Do you have to match mark on Hyundai Santa Fe?
If you are only removing the 2 bolts holding the carrier bearing to the frame and not separating the carrier bearing itself, you do not need to match mark. There is no adjustment on the bracket and only goes back one way in one position If you are separating the carrier bearing(front shaft from rear shaft), then you do need to match mark.
Do you have to drop rear drive shaft carrier?
There is no adjustment on the bracket and only goes back one way in one positionIf you are separating the carrier bearing(front shaft from rear shaft), then you do need to match mark. If you drop the front or rear shaft from their differentials, then you match mark them.
There is no adjustment on the bracket and only goes back one way in one positionIf you are separating the carrier bearing(front shaft from rear shaft), then you do need to match mark. If you drop the front or rear shaft from their differentials, then you match mark them.
If you are only removing the 2 bolts holding the carrier bearing to the frame and not separating the carrier bearing itself, you do not need to match mark. There is no adjustment on the bracket and only goes back one way in one position If you are separating the carrier bearing(front shaft from rear shaft), then you do need to match mark.
How to remove and replace the drive shaft carrier bearing?
After marking the companion flange and flange yoke, and the differential companion flange and rubber coupling with a line, remove the propeller shaft. When removing the propeller shaft, be careful not to damage the boot. Insert a piece of cloth into the boot to prevent it from being damaged. 1.