How to remove front disc brake on Hyundai Sonata?
Loosen the hose eyebolt (B) and caliper mounting bolts (C), then remove the front caliper assembly (A). Do not loosen the bolts (E) instead of guide rod bolt. 3. Remove the front brake disc by loosening the screws (A). 1. Remove the brake hose mounting bracket bolt (A). 2. Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.
How do you remove a rotor from a parking brake?
You may have to adjust the parking brake and back it off the rotor in order to remove the rear rotor. Tech Tip: Removing A Rear Rotor Stuck On The Parking Brake If you are having trouble removing a drum-in-hat rotor, don’t just take a hammer to it.
How do you remove a drum in hat rotor?
You may have to adjust the parking brake and back it off the rotor in order to remove the rear rotor. If you are having trouble removing a drum-in-hat rotor, don’t just take a hammer to it. You may have to adjust the parking brake and back it off the rotor in order to remove the rear rotor.
How can I repair my rear disc brake?
Replace pad shim (D), pad retainers (C) and brake pads (B) in the caliper bracket (A). 1. Check the brake pads for wear and fade. 2. Check the brake disc for damage and cracks. 3. Remove all rust and contamination from the surface, and measure the disc thickness at 8 points, at least, of same distance (5mm) from the brake disc outer circle.
Can you replace the brake pads on a Hyundai Sonata?
Hyundai is finally getting the respect it has long deserved as automaker, and their Sonata mainstream sedan is more popular than ever before. In this video you’ll learn how to replace the rear brake pads and rotors on a Hyundai Sonata quickly and easily.
How to replace rear brake pads and rotors?
Step 5 – Using a pair of dikes remove the rotor retainer clip which is used in initial assembly and will not be reinstalled. Step 6 – Next, use a socket to remove both upper and lower caliper mounting bolts. Use a wrench if necessary to secure the slide.
How do you reset a parking brake rotor?
If a brake caliper utilizes a parking brake mechanism, a caliper reset tool is needed. Step 16 – Once the caliper has been retracted, insert the caliper mounting bracket over the rotor. Step 17 – After fitting the caliper bracket into place, insert the mounting bolts and tighten.
How do you reset a rear brake caliper?
A rear caliper reset tool is necessary for parking brake integrated systems. The reset tool screws the piston back into the caliper. These calipers cannot be compressed with a clamping tool, it can only be reset with the reset tool. A locator slot is used on the inboard piston, which is fitted into a peg located on the backing plate of the pad.
How do you replace a front fender on a Hyundai?
So it appears that there is a tab from the fender, a bracket welded to the unibody, a very thin piece of the insulation and this clip all riveted together. Click to expand… The clip is slipped over a bolt, just pull it off to reveal a bolt with a 10mm nut.
How to repair front disc brake on Hyundai Santa Fe?
1. Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc. 2. If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again. 3.
How do you change the brake pads on a Hyundai?
Set the parking brakes and place the transmission in Park. Open Brake Fluid Reservoir. Start by opening the hood and remove the brake fluid reservoir cap. This is necessary and will make it possible for you to press the caliper pistons in. You will need to do this to fit the new thicker brake pads in the brake caliper.
How do you remove a brake caliper from a car?
Lift the caliper off the brake pads and tie it with a rope to the strut to keep it from falling and void, putting tension on the brake line. Remove Brake Pads Once you remove the two bolts, you will pull out the caliper and remove the brake pads. Loosen the two rotor retaining bolts using a Phillips screwdriver.