How to install a camshaft on a Toyota Camry?
INSTALL No.2 CAMSHAFT a. Put the camshaft on the cylinder head with the painted mark of the link of chain aligned with the timing mark of the camshaft timing sprocket. b. Raising the camshaft, temporarily tighten the sprocket bolt. c. Examine the front marks and unmbers of the 5 bearing caps and install them.
How to install timing chain on Toyota Camry?
Install the timing chain on the camshaft timing gear, with the painted mark of the link aligned with the timing marks of the camshaft timing sprocket. b. Examine the front marks and unmbers of the 5 bearing caps and install them. Then install the 10 bearing cap bolts.
How do you remove camshaft cap on Toyota Camry?
Uniformly loosen and remove the No. 2 camshaft’s 10 bearing cap bolts in the sequence shown in the illustration. Then remove the 5 bearing caps. Raise the No. 2 camahaft and remove it.
Where is timing mark 0 on Toyota Camry?
SET No. 1 CYLINDER TO TDC/COMPRESSION Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover. Check that the timing marks of the camshaft timing gear and camshaft timing sprocket are aligned with the timing marks of the bearing cap as shown in the illustration.
What are the timing marks on a Camry?
Ok The best way I can describe it is after I get the timing belt installed, the tension set, then turn the crank the 2 revolutions clockwise the camshaft timing mark does not line up again, it is about a 1/4″ from making the full revolution and lining back up. This is a 1999 camry with 2.2I4.
What’s the best way to turn a cam and Mark?
Rotate the cam and mark Top Dead Center (TDC). Turn the camshaft wheel until you see the V-shaped timing mark at the top. If these timing marks are not aligned properly during assembly, the camshaft will be out of phase with the crankshaft and the valves may be damaged if they strike the pistons.
How much torque does a Toyota Camry have?
Torque: 30 N·m (301 kgf·cm, 22 ft·lbf) for bearing cap No. 1 9.0 N·m (92 kgf·cm, 80 in.·lbf) for bearing cap No. 3 16. INSTALL No.2 CAMSHAFT a. Put the camshaft on the cylinder head with the painted mark of the link of chain aligned with the timing mark of the camshaft timing sprocket. b. Raising the camshaft, temporarily tighten the sprocket bolt.
How to replace head gasket on Toyota 2.2L?
Thoroughly detailed video on replacing your head gasket on any vehicle- though a Toyota 2.2L is used in the example. Includes measuring warpage specifications, special tools needed, proper techniques, and options to consider such as machine shop services, used vs new cylinder heads, and more!
Is the timing chain on a Toyota Camry non interference?
I have a 2002 Camry. Only 40,000 Miles. 4 Cyl. The 2AZ-FE Engine. It’s my understanding that this engine has a timing chain (not a belt), and is a NON-Interference engine. With that said, The only maintenance I’m planning for this timing chain is to keep up on the oil changes.
Is there a timing chain on the 2AZ-FE engine?
The 2AZ-FE Engine. It’s my understanding that this engine has a timing chain (not a belt), and is a NON-Interference engine. With that said, The only maintenance I’m planning for this timing chain is to keep up on the oil changes. If the chain breaks (highly unlikely) , or some type of guide or tensioner should fail, I’ll just fix it at that time.
What causes an engine failure on a Toyota Camry?
There is an oil baffle under the valve cover that protrudes under the oil fill cap in the valve cover. The baffle can break off under the valve cover and become lodged between the camshaft gear and the timing chain, causing the motor timing to fail. As this is a zero tolerance interference motor, engine failure can result.
https://www.youtube.com/watch?v=8GoQDZztgzs