How to get the ECM code on a Harley Davidson?

The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run. 2- Push odometer resetbutton in & hold. 3- Turnignition switchto Ignition and release the odometer reset button.

What did the battery light come on on my Harley Davidson?

Rode about 70 miles yesterday. Everything was fine as usual. Stopped for gas. She fired right up. As soon as we hit the road the battery and engine light came on. Pulled into the next gas station and shut her down. Waited a few minutes and she started right back up but lights still on. Headed home.

How to get a diagnostic code for a Harley Davidson?

How do you reset the ECM on a Honda Accord?

Turn your starter switch to the “Run” or “On” position. Insert your key into the ignition and turn it on as well as off four times, relatively quickly, with a second or so pause in each position. Turn the key on, pause, off, pause, on, pause, off, pause, on, pause, off, pause, on, pause, off. Your ECM is now reset. Figure 3.

How to check ECM code on fuel Moto?

Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.

How to reset check engine light on Harley Davidson touring?

You may think you need an expensive code scanner or computer to check and reset CEL codes on your Harley, but the Motor Company designed a diagnostic mode into the computer. All you need are your ignition keys and a finger, and a pen to write down the stored codes before resetting. This article applies to the Harley Davidson Touring (2005-2016).

How to get the trouble codes on a Harley Davidson?

The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.

Where are the fault codes on Elm config?

This is the main screen of ELMConfig – Along the left hand side is the main module navigation, with the Low CAN & High CAN modules. Below this, you can read the fault codes within each module, and also clear the codes to prevent the warning lights showing.

Can you remove the OBD plug from an elm?

Now the ELM is open, you can remove both white plugs pictured below – this will allow us some space to work with. You can also remove the OBD plug by pulling the plug out of the housing, this will allow us to cut the required wires. We will be re-wiring the plug as per the wiring diagram below:

What happens when your ECM goes into limp mode?

If there are any trouble codes, the ECM may enter into “limp mode” or “limp home mode.” This causes the motorcycle to run slow, and not make anywhere near its normal power. In order to clear the codes, you must enter into Diagnostic Mode.

How does the ECM work on a twin cam?

This applies to all Twin Cam and V-Rod models with factory security but may also apply to Twin Cam’s with EFI. The TSM/TSSM and ECM have “learned” passwords that synchronize the control module with several other components. Once you remove a component from this chain the module shuts down and won’t start.

How does smart tune live work on a Harley Davidson?

• Smart Tune Live, a dynamic method to track engine data by running vehicle through a range of RPM and throttle positions, reduces time to modify existing Volumetric Efficiency tables (works on models with factory-installed O2 sensors only)

Is the 2009 Harley Davidson Night Train for sale?

Up for sale is a 2009 Harley Davidson Night Train FXSTB with 5,244 miles. This is the last year the Night Train was made and may be the last chance you have to own one as close to new as this one. The reason I am selling is that I just do not have the time to ride it since my daughter was born.

What kind of tires does a Harley Night Train have?

Samson ripsaw exhaust, Vance&Hines Fuel Pak, New Tires, Rear wheel powder coated, All Lights are LED, Tribal theme pegs, grips and mirrors, Screaming Eagle forward facing air filter, mounted tachometer, mounted oil pressure gauge. Local pickup only.

Navigation