How to fix p1391 code on Jeep Wrangler?

Fix & Repair a P1391 Code on a Jeep Wrangler, Cherokee or Similar – YouTube P1391 CHRYSLER – Intermittent Loss of CMP or CKP Usually paired with a check engine light on. Crank Position Sensor or Cam Position Sensor intermittent failu… P1391 CHRYSLER – Intermittent Loss of CMP or CKP Usually paired with a check engine light on.

What causes a bad CKP signal on a p1391 Jeep?

P1391 JEEP Possible Causes Faulty Crankshaft Position Sensor (CKP) Crankshaft Position Sensor (CKP) harness is open or shorted Crankshaft Position Sensor (CKP) circuit poor electrical connection Timing belt or chain stretched or jumped Faulty Camshaft Position (CMP) Sensor

What causes an OBDII code on a jeep?

When does the diagnostic trouble code ( DTC ) set?

The Diagnostic Trouble Code (DTC) will set when the PCM detects the actual Camshaft Position Sensor position disagreed with the expected Camshaft Position Sensor level. Need more information on how to fix the P1391 JEEP code?

What are the symptoms of a p0351 DTC?

Symptoms of a P0351 DTC may include: MIL (Malfunction indicator lamp) illumination Engine misfire may be present or intermittent Potential causes of a P0351 code include: Short to voltage or ground on COP driver circuit Loose connection at coil or broken connector locks

What causes a p0351 code on a cop?

Potential causes of a P0351 code include: Short to voltage or ground on COP driver circuit Loose connection at coil or broken connector locks Is the engine misfiring presently? If not, the problem is likely intermittent. Try wiggle testing the wiring at the #1 coil and along the wiring harness to the PCM.

What causes a DTC p0351 ignition coil to set?

If an open or a short is detected in the driver circuit for coil number 1, a P0351 may set. Also, depending on the vehicle, the PCM may also shut down the fuel injector to the cylinder also. Symptoms of a P0351 DTC may include: Potential causes of a P0351 code include: Short to voltage or ground on COP driver circuit

How much does it cost to diagnose p1494 Jeep code?

The cost of diagnosing the P1494 JEEP code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P1494 JEEP code detected? Engine Light ON (or Service Engine Soon Warning Light)

What causes a leak in a p1494 Jeep?

P1494 JEEP Possible Causes 1 Faulty Leak Detection Pump (LDP) 2 Leak Detection Pump (LDP) harness is open or shorted 3 Leak Detection Pump (LDP) poor electrical connection

How to diagnose a jeep EVAP pump leak?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P1494 JEEP code is 1.0 hour of labor.

Where was the 2002 Jeep Grand Cherokee last serviced?

1st owner drove an estimated 0 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 0 miles/year • 4th owner drove an estimated 0 miles/year • 5th owner drove an estimated 0 miles/year. Last serviced at 105,496 miles in Doral, FL on 01/12/17 • Vehicle serviced • Airbag computer/module reprogrammed.

What is the meaning of the error code p1391?

Definition. Error Code P1391 happens when the PCM (powertrain control module, also known as ECM or engine control module in other vehicle makes) has detected that the actual position of the CMP disagrees with its expected level as set by the manufacturer.

Why is my PCM getting a weak CKP signal?

Open or shorted CKP sensor harness Poor electrical connection in the CKP sensor Stretched or jumped timing belt or chain Open or shorted CMP sensor harness Poor electrical connection in the CMP sensor This could also happen if the coils and injectors are getting fired intermittently. Something you would expect if the PCM is getting a weak signal.

Navigation