How to check the codes of the ECU in a 90-95 Nissan 300ZX?
This write-up explains how to check the codes of the ECU in a ’90-’95 300ZX. You guys with the ’96 300ZX have the OBDII system. 1. Pull back the floor mat. 2. Pull back the carpet. It is held down with three Velcro strips. 3. Remove the wood floorboard, it is held on by 4 10mm bolts (red circles). 4. Now you will see the ECU.
How to check Nissan 300ZX diagnostics on computer?
3. Consult Diagnostics (computers!): The easiest way of checking codes is using the Consult system. You can do this with a computer and a BlaZt Cable, for example. Software includes Conzult, Nissan Datascan, and several others.
How to check the codes of the ECU?
The ECU is now checking the left O2 sensor. Run the engine at 2000rpms for 2 minutes and watch the “Check Engine” light. The light should be blinking constantly. 3. To check the right O2 sensor, turn the screw on the ECU fully clockwise, wait 2 seconds, and then turn back fully counter-clockwise, the ECU will now be checking the right O2 sensor.
What does code 34 read on Nissan 300ZX?
For example, Code 34 (Detonation Sensor Circuit) would read like this: If you’re reading off the CEL, it would blink the same way. 54: Signal Circuit from A/T to Transmission Controller Unit. 55: No malfunction.
This write-up explains how to check the codes of the ECU in a ’90-’95 300ZX. You guys with the ’96 300ZX have the OBDII system. 1. Pull back the floor mat. 2. Pull back the carpet. It is held down with three Velcro strips. 3. Remove the wood floorboard, it is held on by 4 10mm bolts (red circles). 4. Now you will see the ECU.
What kind of port does Nissan consult use?
*NOTE: Some vehicles up to year 2004 use OBDII (K-Line) for communicating with the ECU, BUT still use the Consult I (14pin) port for diagnostics. CalumSult 0.08h, WinXP, ROM dumping/real time graph.
Is the Nissan consult 14 pin diagnostic interface compatible?
The Nissan Consult 14 pin diagnostic interface that pairs with your PC using a high-speed USB connection and is compatible with a wide range of available third party software. This version is fitted with a mini USB port that’s more compact than the older RS232 connection version.
What kind of software does Nissan 300ZX Z32 use?
ConZult for Nissan 300ZX Z32, WinXP, base idle mode, simple bar graph. ScanTechNissan 1.38, Win 2000/XP, ISO 9141, KWP2000, active tests. nProbe hardware stopped 2005.12.31, software by TwinTurbo.NET. PalmZ for Palm PDA by Ztechz forum member MezafitsII.
Where are the diagnostic connectors in a Nissan?
Locations: In the center console. Locations: In or next to the fusebox under the dash panel. In the center console. Locations: Under the drivers seat. Under the passengers seat. Above the passengers side kick panel. In the center console.
How does the voice warning system work on a Nissan 300ZX?
The Voice Warning System used the vehicle’s radio and driver’s door speaker to mute the radio and provide a vocal warning whenever a door was ajar, the exterior lights were left on after the vehicle was turned off, the key was left in the vehicle’s ignition when the driver’s door was opened, or the fuel level was low.
Where is the consult port on a Nissan?
It’s compatible with most Nissan vehicles from 1989-2000 equipped with the 14 pin Gray Consult I connector that’s normally found near the driver’s side fuse box. *NOTE: Some vehicles up to year 2004 use OBDII (K-Line) for communicating with the ECU, BUT still use the Consult I (14pin) port for diagnostics.