How to change the water pump on a Jeep Liberty?
How to Change a Jeep Liberty Water Pump 1 Place a drain pan underneath your Jeep’s radiator. 2 Drain the cooling system from underneath the vehicle by twisting the radiator drain plug counterclockwise with a wrench. 3 Open the hood and disconnect the battery negative terminal with a wrench.
How do you replace a water pump in a car?
Lift the fan shroud and fan assembly together and carefully slide them back into the engine bay. Replace the bolts in the fan shroud and the nut holding the fan assembly to the water pump. Replace the negative battery terminal. Remove the radiator and replenish the cooling system with a 50/50 mixture of water and coolant.
How do you replace a water pump gasket?
Use gasket sealer to hold a new water pump gasket to the engine block. Reattach the water pump to the engine block with the original bolts. Replace the lower radiator hose using new hose clamps. Relieve the tension on the belt tensioner and replace the fan belt.
How do you reattach a water pump to an engine block?
Use gasket sealer to hold a new water pump gasket to the engine block. Reattach the water pump to the engine block with the original bolts. Replace the lower radiator hose using new hose clamps. Relieve the tension on the belt tensioner and replace the fan belt. Restore the belt tension by removing the ratchet wrench.
Lift the fan shroud and fan assembly together and carefully slide them back into the engine bay. Replace the bolts in the fan shroud and the nut holding the fan assembly to the water pump. Replace the negative battery terminal. Remove the radiator and replenish the cooling system with a 50/50 mixture of water and coolant.
Use gasket sealer to hold a new water pump gasket to the engine block. Reattach the water pump to the engine block with the original bolts. Replace the lower radiator hose using new hose clamps. Relieve the tension on the belt tensioner and replace the fan belt.
How does the cooling system on a Jeep Liberty work?
Your Liberty’s cooling system works by cycling the engine coolant from the engine through the radiator. The water pump pushes the water through the entire system. The thermostat opens up once the engine reaches operating temperature and allows coolant in.
How do you remove a water pump from an engine block?
Remove the bolts on the water pump with a wrench. Carefully remove the water pump from the engine block. Do not use sharp tools to pry the pump off as you can damage the mating surfaces. Discard the old water pump gasket. Use gasket sealer to hold a new water pump gasket to the engine block.
Can a Jeep Liberty be swapped for a Chrysler 3.7?
Any Chrysler 3.7 from just about anything 2005-2012 (2004? Not sure when they changed reluctors) We put a 2012 liberty motor in our 2006 commander, swapped the oil pan ( liberty should be the same) , intake, throttle body the temp sensor and cam sensor. The rest was bolt up.
Can you change the engine on a Jeep Liberty?
Two of the tricks is the power steering and ac compressor can be left attached and just pushed aside. Probably the same trick for a lot of jeeps. Just about any vehicle needing a engine is going to be costly unless it’s ubiquitous like a 4.0 . I found the 3.7 a hard engine to find a good cheap one.
When to change spark plugs on Jeep Liberty?
Something to keep in mind is most used warranties and rebuilt for that matter require certain things be changed for a 90 day guarantee to be honored. Stuff like water pump, spark plugs, oil seals replaced.
Can a 2012 Jeep Liberty be swapped to a 06?
When i swapped the 2012 in to the 06, it was very straight forward and a low mileage engine to, skipped a ton of steps like the rear main seal and crank seal because they were still perfect at 30k mikes and three years old at the time I bought it.
How do you recharge a 2005 Jeep Liberty?
Open the 2005 Jeep Liberty’s hood and locate the A/C system. You are looking for aluminum tubing with a high- and low-side port. Remove the cover from the low-side port and place the cover in a safe spot for later. Fit the recharging hose snugly and securely onto the low-side port.
Remove the bolts on the water pump with a wrench. Carefully remove the water pump from the engine block. Do not use sharp tools to pry the pump off as you can damage the mating surfaces. Discard the old water pump gasket. Use gasket sealer to hold a new water pump gasket to the engine block.
How can I tell if my water pump is bad?
The two most common signs of a bad pump are leaks and noises. Leaking water pumps can result in damage to the drive and timing belts, and cause the engine to overheat. A failed water pump can be caused by other problems in the cooling system, such as a bad thermostat, radiator or head gasket.