How to change serpentine belt on Camaro Firebird?
Remove the bolts holding the lid to the front core support, and remove the bolts holding the intake tube to the throttle body. Cold air intakes and other aftermarket solutions may be different in this regard. Figure 1. SLP lid on LS1. Before doing anything, check to see if your belt routing diagram is still there in your engine bay.
How is the serpentine belt in a Chev?
Pictures, diagrams of serpentine belt routing. 2.4L. Belt Diagram 3.4 DOHC Cam Engine Drive Belt Diag… 3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro…
How do you remove a serpentine belt from a HHR?
Maneuver the pulley so that the tensioner releases the tension from the serpentine belt. Use a tube over the handle of the ratchet if you need further extension to depress the tensioner. Remove the serpentine belt completely from the HHR. Install the new serpentine belt by hand, using the “Belt Routing Diagram” over the radiator as a visual guide.
How often should a serpentine belt be replaced?
Under ideal circumstances, your car’s serpentine belt should last 60,000–100,000 miles. It’s important to replace this belt as part of your vehicle’s scheduled maintenance (even if it looks okay) to avoid it breaking while you’re on the road. Not sure when your serpentine belt was last replaced?
Remove the bolts holding the lid to the front core support, and remove the bolts holding the intake tube to the throttle body. Cold air intakes and other aftermarket solutions may be different in this regard. Figure 1. SLP lid on LS1. Before doing anything, check to see if your belt routing diagram is still there in your engine bay.
How often should I Change my serpentine belt?
It is best to replace your belt every five years or 50,000 miles. Check out how to below! Depending on the air intake that you have fitted to your LS1, you may find this easier to remove the lid before beginning. Remove the bolts holding the lid to the front core support, and remove the bolts holding the intake tube to the throttle body.
Can you remove the lid on a Camaro Firebird?
Depending on the air intake that you have fitted to your LS1, you may find this easier to remove the lid before beginning. Remove the bolts holding the lid to the front core support, and remove the bolts holding the intake tube to the throttle body.
How do you change the belt on a LS1?
SLP lid on LS1. Before doing anything, check to see if your belt routing diagram is still there in your engine bay. If not, take a picture of the belt routing so you have an idea of how to put it back on. Then, place your 15mm wrench on the tensioner pulley bolt and turn it clockwise as far as you can go.
What kind of belt is on a Vortec truck?
4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro… Supercharged 3.8L V6 Drive Belt rou… Vortec 5.3 and 4.8L V8 Truck Belt R…
It is best to replace your belt every five years or 50,000 miles. Check out how to below! Depending on the air intake that you have fitted to your LS1, you may find this easier to remove the lid before beginning. Remove the bolts holding the lid to the front core support, and remove the bolts holding the intake tube to the throttle body.
How do you replace the serpentine belt on a car?
Lift the car and set it on jack stands. Loosen the tensioner pulley near the top of the engine. Then get underneath the engine and slip off the serpentine belt from around the alternator pulley. If you can’t remember the last time you replaced your serpentine belt, consider now a good time to do so. Figure 2. Loosen the tensioner bolt. Figure 3.
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
Lift the car and set it on jack stands. Loosen the tensioner pulley near the top of the engine. Then get underneath the engine and slip off the serpentine belt from around the alternator pulley. If you can’t remember the last time you replaced your serpentine belt, consider now a good time to do so. Figure 2. Loosen the tensioner bolt. Figure 3.