How to bleed a Honda V45 Magna 750C clutch?

1983 Honda V45 Magna 750C Clutch Bleed Solution – YouTube I rebuilt the clutch master cylinder & slave cylinder and found out the best way to bleed the clutch.Clutch Master Cylinder & Slave Cylinder Rebuild

Where is clutch master cylinder on Honda Magna?

Lift the Magna onto its center stand. Turn the handlebars to the right until the clutch master cylinder, located on the left handlebar, is completely level. Remove the fluid reservoir lid from the clutch master cylinder, using a Phillips screwdriver.

Is there a way to bleed the clutch?

I rebuilt the clutch master cylinder & slave cylinder and found out the best way to bleed the clutch.Clutch Master Cylinder & Slave Cylinder Rebuild AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features

Where is the bleed valve on a Honda?

Follow the clutch hose from the clutch master cylinder to the clutch slave cylinder, located on the left side of the engine crankcase. Pull the rubber dust cover off the bleed valve, located on the top of the clutch slave cylinder.

How do you Bleed a clutch master cylinder?

Check out this video to see where the air bubble is, where it comes from and how to easily get it out. It takes about 3 1/2 ounces of brake fluid to get the air bubble out or the clutch master cylinder using this method. Once the system has been bled and re-installed in the vehicle, a gravity bleed of the clutch slave cylinder will finish the job.

Where is the bleed valve on a Honda clutch?

Pull the rubber dust cover off the bleed valve, located on the top of the clutch slave cylinder. Place an 8 mm box wrench over the bleed valve, then push a 3-foot length of clear plastic tubing over the bleed valve outlet.

When did the Honda V45 Magna come out?

The bike ended up being very comfortable, powerful and stylish and it gave birth to an entire new concept of motorcycle, the power cruiser. In 1982 Honda launched a 750cc power cruiser called V45 Magna.

What was the displacement of a 1983 Honda Magna?

The 1983 V65 Magna was competing with the new released Yamaha V-max powerful motorcycle and later with Suzuki’s response to Magna, the Madura. This model offered also a smaller engine displacement of 700cc, but while the Magna displaced 1100cc, the big Madura, as well as the V-max, displaced 1200cc.

What was the color of the 1987 Honda Magna?

The 1987 V45 Magna was either Candy Wave Blue or Candy Bourgogne Red painted and 1988 brought black paint instead of blue. The air cleaner war wrinkle black with a “V45” emblem, and the “Magna” tank decal was silver.

Are there any problems with a hydraulic clutch?

This is my first bike, and first time with a hydraulic clutch, but I had no problems bleeding the front brakes when they were dry. You have fluid flowing through the system, so you have a large amount of air trapped at the master cylinder, inside the banjo fitting which attaches the line.

What happens if the hole in the clutch is blocked?

If the hole (s) are blocked, you will not get much pressure. You wouldn’t get a free flow of fluid through the bleeder, either, but a vacuum pump would still get some. You’ve clearly still got a lot of air in the system.

What kind of engine does a Honda VF500C have?

The Honda VF500C was a motorcycle produced by Honda from 1984 to 1985 and more commonly known as the V30 Magna. It could reach a top speed of 196.4 km/h. The engine was a Liquid cooled cooled Four stroke, 90°V-four cylinder, DOHC, 4 valve per cylinder. The engine featured a 11.0:1 compression ratio.

What’s the redline on a Honda VF500C?

Both primary and final drive ratios are the same, but the internal transmission ratios have been stirred around. The Magna’s redline sits at 11,500 rpm, which is 500 rpm lower than the Interceptor’s. The Magna’s reduced intake and exhaust breathing ability makes the extra revving unnecessary.

Where is the fuel tank on a Honda VF500C?

Honda engineers ran into a few problems when it came time to mate the V-4 engine to the required custom-styled bodywork. With all four carburetors set in the engine’s V and a large airbox sitting on top of them, little space is left for the fuel tank.

Where is the bleeder screw on a Honda bike?

Follow the clutch line from the clutch master cylinder to the clutch slave cylinder on the motor’s clutch cover. Locate the bleeder screw on the top left side of the clutch slave cylinder. Slip one end of a piece of clear plastic tubing over the bleeder screw and place the opposite end into a container.

Where is the bleed valve on a clutch slave?

Navigation