How much does it cost to replace serpentine belt Subaru?
Subaru Outback Serpentine/Drive Belt Replacement costs $164 on average.
| Car | Service | Shop/Dealer Price |
|---|---|---|
| 2004 Subaru OutbackH6-3.0L | Service typeSerpentine/Drive Belt Replacement | Shop/Dealer Price$230.47 – $310.24 |
| 2012 Subaru OutbackH6-3.6L | Service typeSerpentine/Drive Belt Replacement | Shop/Dealer Price$215.87 – $286.94 |
How much does a mechanic charge to replace a serpentine belt?
Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more. This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour. The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.
Is it hard to replace a serpentine belt?
Serpentine belt replacement is easy because today’s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
What happens if I don’t change my serpentine belt?
If the serpentine belt completely fails and breaks, then your car will break down. In addition, you will notice a loss of power steering, the air conditioning will not work, and the engine will no longer be able to be cooled like it should be.
How long can you drive with a bad serpentine belt?
How long will my car run with a broken serpentine belt? There are a few variables involved in the answer, but it should be able to run between 20 to 90 minutes. If it is a hot summer day, your engine can overheat very quickly without the coolant being pumped through the radiator.
When should I replace my serpentine belt Subaru?
As a precaution, Subaru recommends changing a timing belt many thousands of miles before the part reaches any risk of failure. Generally, this replacement interval is between 50,000 and 100,000 miles.
Can I drive with a bad serpentine belt?
The short answer is yes, your car will start even if the serpentine belt is broken or missing. To get the car going, the battery sends power to your starter motor. The starter motor provides enough power to get your engine moving and the combustion process started.
Can you drive without a serpentine belt?
Under no circumstances can you drive a vehicle without a serpentine belt because the serpentine belt serves the important function of delivering antifreeze to important parts of the engine. The serpentine belt drives the water pump, and without it, there is insufficient coolant flow to maintain the engine temperature.
How far can you drive without a serpentine belt?
Can you drive with a broken serpentine belt?
Will a new serpentine belt improve performance?
Not really. All of your accessories(power steering, air-conditioning, etc.) put drag on the engine; which is why reducing the load from accessories (via under-drive pulleys or simply disabling the accessories) can help with performance.
Can you drive with damaged serpentine belt?
How do you replace a serpentine belt pulley?
Using the breaker bar or serpentine belt tool, move the tensioner arm against the spring as far as it will move, to its stop. The tensioner arm should move smoothly throughout its range of travel, with firm spring pressure and without binding. Most tensioner pulleys can be replaced independently of the tensioner itself.
What kind of car has serpentine belt problems?
If a belt problem still isn’t solved after doing all of the above, your car may have a specific problem unique to that make and model. Certain vehicles have known serpentine belt problems, such as 1996–2000 Chrysler-built minivans with the 3.0-, 3.3-, and 3.8-liter engines.
How can I tell if my serpentine belt is out of alignment?
Belt tension on the pulley pulls the shaft off center, which puts that pulley out of alignment with the other pulleys. Pulley alignment can be checked with a straightedge. Place the straightedge across two pulley faces. The straightedge should lie flat across them. If it doesn’t, one of the pulleys is misaligned.
What happens when you apply dressing to a serpentine belt?
But, when applied to a serpentine belt, the dressing will be spread into the pulley grooves. Once there, it will attract and hold dirt and grit. The dirt will start the belt slipping again and all of the dirt and belt dressing will have to be cleaned out of the pulley grooves before a new belt is installed.