How long does it take to remove an engine from a Pontiac Bonneville?
Removing the engine in your Pontiac Bonneville, with the right tools and correct knowledge, should take part of a day. Whether your engine locked up, burned out, or you want to replace it with something with more power or better gas mileage, removing an engine can be hard work, so you might want to have a friend help you.
How do you remove exhaust manifold from Bonneville?
Remove the bolts from the exhaust manifold and remove the exhaust manifold with the wrench. Remove the bolts that connect the engine to the transmission. Slide underneath the Bonneville and remove the starter and exhaust pipes with the wrench and ratchet set. Remove the bolts from the transmission that connect to the engine with a wrench.
How do you remove the hood from a Bonneville?
Open the hood and, using a wrench, remove the bolts from the support arms on the inside of the hood and remove the hood. Disconnect the negative cable off the battery. Raise the front end up off of the ground with the jack and rest the Bonneville on jack stands.
How do you remove the starter from a Bonneville?
Slide underneath the Bonneville and remove the starter and exhaust pipes with the wrench and ratchet set. Remove the bolts from the transmission that connect to the engine with a wrench. Use a ratchet set to remove the bolts from the motor mounts. Remove the jack stands for underneath the Bonneville and return the front end to the ground.
Why do you need a timing cover on a Pontiac?
Keeping a Pontiac engine cool is vital to it lasting. We get a lot of questions regarding timing covers and water pumps. We have taken the time to show each timing cover and address the ways to identify them.
How do you change the timing cover on a car?
Drive out the crankshaft seal with a hammer and punch. This is the rubber seal around the crankshaft and the timing cover. Tap the new crankshaft seal into the timing cover. The seal should be seated into the correct place on the timing cover. It will seal when the cover is bolted onto the engine. Coat the seal with oil.
What was the timing cover for a 1964 Pontiac?
Early 8 bolt designs are notorious for cooling issues. The 2pc plate we sell without the notch works in all 1964-68 models regardless of timing cover. These 2pc water pump plates take a single water pump gasket. In 1969 the 11 bolt timing cover and water pumps were introduced with much more efficient cooling.
What’s the best way to remove a timing chain?
Put the bolt partially back in the bolt hole and use a harmonic balancer removal tool. The tool should not be a jaw type tool, but instead should apply all of the removal force to the center of the assembly. This protects the rubber ring in the harmonic balancer. Remove the timing chain cover.
What kind of features does the Pontiac Bonneville have?
The Pontiac Bonneville comes in a four-door sedan with three trims – the SE, the SLE and the SSEi. All of Bonneville’s trim levels feature power steering, air conditioning, power locks, power mirrors, cruise control, fog lamps and new stereo sound system.
Why does the idler arm separate on a Pontiac Bonneville?
GENERAL MOTORS CORP. POSSIBILITY THAT, AFTER EXTENDED MILEAGE, THE IDLER ARM ASSEMBLY COULD SEPARATE DURING VEHICLE OPERATION AND RESULT IN A SEVERE PULL TO THE RIGHT AS BRAKES ARE APPLIED AT LOW TO MODERATE SPEED. (INSPECT AND RE- PLACE IDLER ARM ASSEMBLY AS REQUIRED.) GENERAL MOTORS CORP.
What is the control arm on a Bonneville?
Control Arm with Ball Joint Assembly, Front Upper Passenger… Control Arm with Ball Joint Assembly, Front Upper Driver and… Control Arm with Ball Joint Assembly and Tie Rod End Kit,… Control Arm with Ball Joint Assembly, Front Upper Driver Side… Control Arm with Ball Joint Assembly, Front Upper Passenger…
What was the name of the Pontiac Bonneville in 1982?
The 1982-1986 models were officially known as the Pontiac Bonneville Model G (built on the GM “G” platform ), although later models were not badged as such. Styling was revised to bear a closer resemblance to the departed B-body Bonneville and coupes were dropped.
What kind of suspension does a Pontiac Bonneville have?
A proven Strato-Flight Hydra-Matic 4-speed spins a correct GM axle that literally sails the engine through its broad power band. Under that capable drivetrain, a factory-spec suspension is equipped with factory power steering. Power-assisted drum brakes provide adequate stopping prowess.
Removing the engine in your Pontiac Bonneville, with the right tools and correct knowledge, should take part of a day. Whether your engine locked up, burned out, or you want to replace it with something with more power or better gas mileage, removing an engine can be hard work, so you might want to have a friend help you.
What kind of carburetor does a Pontiac Bonneville use?
The 389 cubic inch plant was replaced with 400 cu in (6.6 L) one, and the 421 cubic inch plant was replaced with a 428 cu in (7.0 L) one. As per GM’s internal edict, the multi-carburation setups found on earlier cars were replaced with the new Quadra Jet “spread bore” carburetor.