How does the knock sensor on a Chevy truck work?
The knock sensor sends a signal to the PCM (the truck engine’s computer) to tell the computer about ignition timing. The knock sensor uses two flat-response two-wire sensors. They produce voltage based on engine vibration and noise level.
What are the symptoms of a bad knock sensor?
Bad knock sensor symptoms 1 A failed knock sensor will register a trouble code and illuminate the Check Engine lamp (CEL), although some engines… 2 Misfire 3 Vibration, especially at highway speed 4 Thumping or knocking noise from the engine 5 Poor fuel economy and acceleration More …
Is there a knock sensor problem on my Hummer?
In fact, if you have a 4.8 L 5.3 L or 6.0 L in any General Motors vehicle, including a Hummer or Pontiac, you will probably run into a check engine light indicating a defective knock sensor at some point.The check engine light registering a code P0332 or a P0327 is often the first sign you have this common problem.
Where are the knock and Ping sensors located?
It’s a piezoelectric automotive sensor that produces a small voltage signal when it hears internal engine noise that we often call knock and ping. This is why the location of the two sensors is a problem. In order to hear the engine noise reliably the sensors are buried under the intake manifold.
Bad knock sensor symptoms 1 A failed knock sensor will register a trouble code and illuminate the Check Engine lamp (CEL), although some engines… 2 Misfire 3 Vibration, especially at highway speed 4 Thumping or knocking noise from the engine 5 Poor fuel economy and acceleration More
Where are the knock sensors on a GM car?
If the computer does not pull back on the ignition timing and allows the detonation to continue, the heat generated from the process can cause major damage to the delicate aluminum engine parts. The first thing that’s wrong with the GM knock sensors is they’re located in a tunnel underneath the intake manifold.
In fact, if you have a 4.8 L 5.3 L or 6.0 L in any General Motors vehicle, including a Hummer or Pontiac, you will probably run into a check engine light indicating a defective knock sensor at some point.The check engine light registering a code P0332 or a P0327 is often the first sign you have this common problem.
How much does it cost to replace a knock sensor?
The good news is that it won’t cost you an arm and a leg to replace a bad knock sensor. If you have a standard economy vehicle, you can expect to pay anywhere from $120 to $500 for replacing your knock sensor.
What are the codes for the knock sensor?
Eventually this turns on the check engine light and sets the codes P0332 and P0327. Note that often either one or the other code will set. Regardless if one or both codes are set, not only should the two original knock sensors be replaced, but you should also replace the harness.
Can you test the O2 sensor on a GM 4.3L?
Testing the oxygen sensor (commonly referred to as O2 sensors) on your 4.3L, 5.0L, or 5.7L GM vehicle is not that hard to do. Since oxygen sensors are not cheap and sometimes the PCM (Powertrain Control Module = Fuel Injection Computer) accuses them of being bad, when they aren’t, testing them is a good idea and this article will help you.
Are there any knock sensor problems on GM trucks?
Knock Sensor Problems on GM Vehicles. Knock sensor problems are common on 1999-2007 Chevy Silverado, Express Van, Tahoe and Suburban trucks. Of course, this means that the GMC Sierra and Yukon of the same years have the same issues.
Eventually this turns on the check engine light and sets the codes P0332 and P0327. Note that often either one or the other code will set. Regardless if one or both codes are set, not only should the two original knock sensors be replaced, but you should also replace the harness.
It’s a piezoelectric automotive sensor that produces a small voltage signal when it hears internal engine noise that we often call knock and ping. This is why the location of the two sensors is a problem. In order to hear the engine noise reliably the sensors are buried under the intake manifold.
Are there any aftermarket sensors for GM cars?
After doing the job a few times I’ve learned I can save by using the Dorman aftermarket harness. It works well and carries a reasonable price tag. However, I would recommend going with the delco sensors as I had problems with the cheaper ones being defective right out of the box. The job is time-consuming, but straightforward.
The knock sensor sends a signal to the PCM (the truck engine’s computer) to tell the computer about ignition timing. The knock sensor uses two flat-response two-wire sensors. They produce voltage based on engine vibration and noise level.
What is the code for the knock sensor?
Check engine light is on with code P0327 (knock sensor 1 circuit low). Before I take off the intake and replace it, I was wondering if someone could tell me what steps to do to verify it’s the actual sensor itself and not something else. I’ve read several forums where people replaced both sensors and wiring harness and that not fixing the issue.
Can a bad knock sensor cause engine damage?
A bad knock sensor can cause some serious engine damage. Before that happens, check out this handy guide on replacing knock sensors in your Silverado. This article applies to the Chevrolet Silverado GMT800 (1999-2006).