How do you replace the pulley on a Honda Civic?
Attach a long breaker bar to the “handle” end of the tool. It should be angled downward against the ground as a brace. Next, attach a 17mm socket to a long extension, and attach it to the crank pulley bolt through the center of the tool. Then, using another large breaker bar, crank on the pulley bolt counterclockwise.
Do you have to change struts on Honda Civic?
It has one of the largest pools of aftermarket parts available for any production vehicle. Whether you need to change your Civic’s struts because they are going bad or because you have installed a new lower set of performance coil springs, you can save yourself money by doing the work yourself.
How do you replace the crankshaft on a Honda Civic?
The first step is to lift the front end of the car. You’ll want to get it as high as possible. Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel.
How do you jack up a Honda Civic?
Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel. The crankshaft pulley is the single, large pulley at the bottom of the engine. Figure 1. Diagram of the jacking points. (Related Article: How to Jack Up Your Civic – Honda-Tech.com)
What kind of strut assembly does Honda Civic use?
Honda Civic 2002, RoadMatic™ Complete Strut Assembly by Monroe®. This ready-to-install complete strut assembly includes everything needed for strut replacement in an affordable, fully-assembled unit. You save time because spring… Honda Civic 2002, Complete Strut Assembly by FCS®.
What kind of suspension does Honda Civic 2002 have?
Honda Civic 2002, Bare Strut by FCS®. FCS bare shocks and struts are engineered to restore your vehicle’s handling and control. Shocks, struts, and cartridges are a great option to restore OE performance and normal driving conditions. Honda Civic 2002, Complete Strut Assembly by FCS®.
How do you replace shocks on a Honda Civic?
Remove the 14mm pinch bolt from the damper. Locate the two damper fork bolts that connect the damper fork to the lower control arm. With your socket and ratchet, remove the two 17mm damper fork bolts. Pull down on the damper fork, and away from the bottom strut. Repeat this step on the other side.
What are the ball joints on a Honda Civic?
This article applies to the Honda Civic (1992-2000). Ball joints are the smallest components that play a big role in making sure you arrive safely to your destination. Think of them as pivots that allow the suspension to flex as your wheel moves. You can tell if they need a replacement just by looking at them.
Where do you put the belt in a Honda Civic?
Route the new belt through the pulleys in the Honda Civic. Start with the crankshaft pulley and work your way through the other pulleys in the engine. Refer to the belt configuration chart for proper routing. Ensure that the grooves on the inside of the new belt match up with the grooves on the pulley.
How to get a 1995 Honda Civic hatchback?
Follow three simple steps to get to your desired version of the Honda Civic Hatchback 1995. First, select the trim that you’re looking for in the drop-down below. Next, select the engine you’re looking for from the second drop-down. Finally, Select the exact version you’re looking for.
Can you remove the pulley on a Honda Civic?
With the bolt removed, you should be able to just pull off the crankshaft pulley. If your Civic has the drive belt still attached, you’ll need to remove it before pulling off the crankshaft pulley. You’ll need to loosen the alternator retaining bolt in order to relieve tension on the belt.
Route the new belt through the pulleys in the Honda Civic. Start with the crankshaft pulley and work your way through the other pulleys in the engine. Refer to the belt configuration chart for proper routing. Ensure that the grooves on the inside of the new belt match up with the grooves on the pulley.
Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel. The crankshaft pulley is the single, large pulley at the bottom of the engine. Figure 1. Diagram of the jacking points. (Related Article: How to Jack Up Your Civic – Honda-Tech.com)
Can a crankshaft seal be replaced on a Honda Civic?
Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.